Floe Cargo Max 9.5-73 User manual

650-72000-00 All material copyright ©2017 FLOE International, Inc. Unauthorized reproduction is strictly Prohibited. Specifications subject to change without notice. 8/7/17
1
Cargo Max Assembly Instructions
9.5-73
11-73
13-73
TOOLS REQUIRED
1. ¾” Socket / Wrench (2) 5. ½ Drive Extension
2. 7/8” Wrench (Tongue Nut) 6. Torque Wrench
3. 13/16” ½ Deep Socket (Lug Nuts) 7. Cordless Drill
4. #2 Phillips Bit (License Plate Bracket)

650-72000-00 All material copyright ©2017 FLOE International, Inc. Unauthorized reproduction is strictly Prohibited. Specifications subject to change without notice. 8/7/17
2
Cargo Max Assembly Components
Sub-assembly
Components
1. Bed & Frame
(Wired w/ side, clearance, tail
lights) ASSEMBLED
2. Axle, Hubs, Tires ASSEMBLED
3. Tailgate Ramp ASSEMBLED
4. Tongue & Tongue Jack ASSEMBLED
5. Wheels & Tires ASSEMBLED

650-72000-00 All material copyright ©2017 FLOE International, Inc. Unauthorized reproduction is strictly Prohibited. Specifications subject to change without notice. 8/7/17
3
Cargo Max Assembly –Step 1
ATTACHING THE AXLE
Fig. 1A
1. Locate the axle isolation strips packed in the
assembly components kit.
2. Place an isolation strip on the two inside
surfaces of the axle mount as shown in Fig.
1A.
3. Place the trailer frame on the axle mounts,
aligning the holes in the axle mount with
the front two holes in the frame. Note the
orientation of the torsion arms in Fig. 1B.
4. Insert (2) ½-13 x 3-1/4” bolts through the
two washers and through the bottom holes
on the axle beam brackets as shown in
Fig.1B.
5. Fasten with (2) flat washers and (2) nylock
nuts. Make sure that the axle mount and
axle beam are tight together with no gap
before tightening. Torque to 40 FT/LBS.

650-72000-00 All material copyright ©2017 FLOE International, Inc. Unauthorized reproduction is strictly Prohibited. Specifications subject to change without notice. 8/7/17
4
Cargo Max Assembly –Step 2
ATTACHING THE TIRES
1. Attach (1) tire w/rim to each axle hub w/
valve stem toward the outside of the trailer
frame (see Fig 2A).
2. Secure with (5) ½-20 lug nuts per rim.
3. Start all lug nuts by hand to prevent cross
threading with the beveled side of the nut
toward the wheel –and to ensure proper nut
to rim contact.
4. Tighten the lug nuts in sequence (see Fig.
2B) in stages.
First tighten to 25 FT/LBS, then to 60
FT/LBs, then finally to 80 FT/LBS.
Inflate the tires to 80 PSI maximum.
New wheels should be re-torque after the first
50 to 100 driving miles.

650-72000-00 All material copyright ©2017 FLOE International, Inc. Unauthorized reproduction is strictly Prohibited. Specifications subject to change without notice. 8/7/17
5
Cargo Max Assembly –Step 3
TILT CLAMP & LIMITER STAP Assembly,
TONGUE Assembly
Tilt Clamp & Limiter Strap Assembly Instructions Attaching the Tongue to the Frame
Slide the Tilt Clamp (1) and Limiter Strap (2)
onto the Tongue (3) as shown in Fig. 3A.
Install so curled cable unwraps as shown when tilted.
Connect tongue harness to trailer harness and pull into tongue until there is 40” hanging out of grommet at the front of the
tongue. Note: Pull trailer harness out of cross member through grommet as needed.
Attach the tongue to the trailer frame using (1)
1/2 x 5” bolt, (1) ½” flat washer, (1) 1” round x
¾” tongue spacer, and (1) ½” heavy nylock nut
as shown in Fig. 3B. Torque to 60 Ft/Lbs.

650-72000-00 All material copyright ©2017 FLOE International, Inc. Unauthorized reproduction is strictly Prohibited. Specifications subject to change without notice. 8/7/17
6
Cargo Max Assembly –Step 4
TAILGATE RAMP INSTALLATION
Insert the Tailgate Ramp into the Hinge Clamps on the bed at an approximately 30-degree angle. See figures
4A & 4B.
NOTE: There are four hinge clamps on the bed. The Tailgate Ramp needs to be aligned to fit within each hinge.
IF the ramp does not align, loosen hinge bolts install ramp and re-tighten hinge bolts.

650-72000-00 All material copyright ©2017 FLOE International, Inc. Unauthorized reproduction is strictly Prohibited. Specifications subject to change without notice. 8/7/17
7
Cargo Max Assembly –Step 5
License Plate Installation
1. Attach the license plate bracket to the trailer frame using the (2) #10 x 3/4”SS Phillips self-drilling, self-
tapping Phillips screws & (2) fender washers located in the components kit.
2. Locate the bracket 5-1/8” from the inside of the driver’s side axle beam on the first cross member in from
the rear (see FIG. 5A & 5B).
*May not be needed in states that do not require a license plate on a utility trailer.

650-72000-00 All material copyright ©2017 FLOE International, Inc. Unauthorized reproduction is strictly Prohibited. Specifications subject to change without notice. 8/7/17
8
Cargo Max Assembly
Assembly Parts Lists

650-72000-00 All material copyright ©2017 FLOE International, Inc. Unauthorized reproduction is strictly Prohibited. Specifications subject to change without notice. 8/7/17
9