American Standard Countertop Bathroom Sink User manual

2
3
730236-100 Rev. D
1
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
!
NOTE: Pictures may not exactly define contour of china and components.
INSTALLATION INSTRUCTIONS
Countertop Bathroom Sink
Introduction: Thank you for selecting our products...products which have been the benchmarks of fine quality for
years. To help insure that the installation process will proceed smoothly, please read these instructions carefully
before you begin. Also, review the recommended tools and materials list; carefully unpack and examine your new
plumbing fixture.
Adjustable Wrench
Channel Lock Pliers Regular Screwdriver
Recommended Tools & Materials
Phillips Screwdriver
Pipe Wrench
Putty Kinfe
Drill Saber Saw
Basin Wrench
Plumbers' Putty or
Caulking
Tubing Cutter
Tape
Measure
Hacksaw
© American Standard Inc. 2003
Using the template provided,locate the position of
thesink. Provide proper clearance under the
countertop for the faucet supply lines, drain assembly
and the structural parts of the cabinet.
NOTE: If replacing an existing sink be certain to shut
off water supply before removing old sink.
Perimeter
of template
Perimeter
of template
A
Drill a clearance hole
inside the perimeter
line of the template.
Cut opening around the
perimeter of the
template.
Mount the faucet and drain assembly (not included)
on the sink following faucet manufacturer's
instructions. Be certain to apply a bead of sealing
putty on the underside of the drain (Part "A") in order
to ensure a watertight seal between the sink and
drain. Remove excess putty after installing drain on
sink.

4
5
6
7
730236-100 Rev. D
AMERICAN STANDARD ONE-YEAR LIMITED WARRANTY
If inspection of this American Standard plumbing product, within one year after its initial installation, confirms that it is defective in
materials or workmanship, American Standard will repair or, at its option, exchange the product for a similar model.
This limited warranty does not apply to local building code compliance; since local building codes vary considerably, the purchaser
of this product should check with a local building or plumbing contractor to insure local code compliance before installation.
This warranty shall be void if the product has been moved from its initial place of installation; if it has been subjected to faulty
maintenance, abuse, misuse, accident or other damage; if it was not installed in accordance with American Standard's instructions; or if it
has been modified in a manner inconsistent with the product as shipped by American Standard.
American Standard's option to repair or exchange the product under this warranty does not cover any labor or other costs of removal
or installation, nor shall American Standard be responsible for any other incidental or consequential damages attributable to a
product defect or to the repair or exchange of a defective product, all of which are expressly excluded from this warranty. (Some
states or provinces do not allow the exclusion or limitation of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory rights that vary from state to state or from province to
province, in which case this warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through the contractor or dealer from or through whom the
product was purchased, or that a service request (including a description of the product model and of the defect) be sent to the following
address:
In the United States:
American Standard, Inc.
One Centennial Ave.
Piscataway, New Jersey 08855
Attention: Director of Consumer Affairs
Toll Free: [phone]
In Canada:
American Standard, Inc.
2480 Stanfield Rd.,
Mississauga, Ontario
Canada L4Y 1S2
Toll Free: [phone]
In Mexico:
Customer Service Manager
American Standard, Inc.
Via Morelos #330
Col. Santa Clara
Ecatepec 55540 Edo. Mexico
Saniwares
BC
Shut-Off
Valves
Before applying the sealant, place the sink
temporarily into the cut-out. Check for alignment and
clearance. Then mark the sink and countertop in
several places as a guide for the installation location.
Connect supply line to faucet (finger tight) and carefully
bend tubes to engage with the supply shut-off valves.
Tighten connections at faucet and shut-off valves for
secure seal.
Connect trap to drain assembly hand tight to check
alignment. It may be necessary to cut off part of the
tailpiece (area "B") or part of the horizontal leg of the trap
(area "C"). Secure joints for watertight assembly.
After checking fit and alignment, turn sink upside
down and apply a generous portion of sealant
around the underside of the rim near the edge.
Carefully lower sink in place, align with marks made
earlier, and press downfirmly. Allow sealant to
set before connecting supplies and drain.