American Standard Green Tea Deck-Mount Bath Filler 7010.900 User manual

*Wrench
Certified to comply with ANSI A112.18.1M
Recommended Tools
*Supplied with Fitting
*Hex key
SPOUT RECESS
Turn off hot and cold water
supplies before beginning.
CAUTION
12
Assemble RUBBER WASHER (4) and BRASS WASHER (5) and
LOCKNUT (6) onto SPOUT SHANK (3). Align SPOUT ASSEMBLY
and from underside of ledge secure SPOUT ASSEMBLY into
position with LOCKNUT (6).
SPOUT ASSEMBLY PREPARE TUBE AND TEE ASSEMBLY
4
2
3
1
3
4
1
2
4
5
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center
VALVE (2) location (between 6-1/2" and 12"). If necessary,
cut and/or bend TUBING carefully. Make sure tube bend is
close to the TEE (1) so that it will not effect the compression
joint at the VALVE CONNECTION.
ADJ. 6-1/2 TO 12
6
5
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
MOUNTING
SURFACE
VALVE inlet is 3/4-inch NPT male.
NOTE
MOUNTING
SURFACE
ADJ. 6-1/2 TO 12
ROUGHING-IN DIMENSIONS
MOUNTING
SURFACE
8-1/16"
DECK-MOUNT BATH FILLER
Installation
Instructions
7010.900
7010.901
1-1/2 MAX.
1-1/4
MAX.
1-3/16 DIA.
3
(H)(C)
1-1/8 DIA.
12 MAX
2-1/16
DIA.
1-1/16 DIA.
3/4-14 MALE
N.P.T. INLETS
Install RING WASHER (1) into SPOUT recess. Check that O-RING (2)
on end of SPOUT SHANK (3) is in place. Insert SPOUT SHANK (3)
through center hole on mounting surface.
GREEN TEA
5-5/16"
3"
3-3/4"
10-5/8"
2-1/16"
DIA.
2-1/8"
3
M968595 Rev.1.2
2-9/16"
Remove COUPLING NUT (3) and FERRULE (4) from each
VALVE (2) and slide onto TUBING (5).
SPOUT
ASSEMBLY
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
7-7/8"
(200mm)

5SERVICE
2
4
5/16'' MIN. MOUNTING
SURFACE
FOR FITTING
LESS SPRAY
11
11
10
1
3
4
Push TUBING (3) ends into VALVE (4) side outlets. Insert VALVES (4)
into mounting holes from underside of ledge.
Press TEE (5) onto SPOUT SHANK (6) making certain that the O-RING (7) is
properly seated on SHANK (6). Push COUPLING (8 or 8a) into TEE (5) and
attach to SPOUT SHANK (6) and tighten. For 7005.901 use a 10 mm
(3/8") hex key.
Install LOCKNUTS (1) and RUBBER WASHERS (2) onto valve shanks.
Place RUBBER RING (10) into ESCUTCHEON ADAPTERS (9) and thread onto
valves until snug against internal stop.
Tighten LOCKNUT (1) to secure VALVE (4) position.
Slide FERRULE (12) and COUPLING NUT (13) to outlet of VALVE (4) and tighten
COUPLING NUT (13) firmly.
Connect HOT water supply to inlet of left VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
VALVE ASSEMBLY
HOT
COLD
12 13
7
6
8
8a
5
13
12
3
4
MOUNTING
SURFACE
Thread of VALVE BODY (4) should extend at least 5/16 inch above
MOUNTING SURFACE (11). If necessary, adjust LOCKNUT (1).
10
9
9
M968595 Rev.1.2
INSTALL HANDLES
To change direction of handle:
8
7
1
2
4
4a
5
3
TOP
SPLINE END DOWN
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without a spline is facing up. Fig. A. Tighten
STEM SCREW (3) to secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (4). Push
LEVER HANDLE ASSEMBLY (4) down onto ADAPTER (1).
Thread base of LEVER HANDLE ASSEMBLY (4a) onto DECK
ADAPTER (5) until snug against mounting surface. Fig. A.
2
90˚
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90˚.
3
2
4
Turn valve to OFF position
Thread HANDLE BASE (1a) counter clock-wise until loose.
Pull HANDLE (1) “UP” firmly to release from ADAPTER (2).
Remove SPRING CLIP (3). Lift STOP WASHER (4), turn 90˚
and replace. Replace SPRING CLIP (3).
Re-install HANDLE ASSEMBLY (1).
1
1a
i
n
s
t
a
l
l
r
e
m
o
v
e

HANDSHOWER INSTALLATION
(FOR MODEL 7010.901 ONLY)
Drop SPRAY ESCUTCHEON (1) through the fourth hole of the tub ledge (12" max from SPOUT
center) with SPRAY ESCUTCHEON (1) directed towards tub center. Be sure RUBBER RING (2)
is properly seated in ESCUTCHEON (1). Install RUBBER WASHER (3) and LOCKNUT (4) from
underside of ledge.
Secure SPRAY ESCUTCHEON (1) by tightening LOCKNUT (4).
Add SEAL WASHER (5) and connect HOSE (10) to outlet nipple
at the bottom of TEE (7). Tighten firmly.
Slip SHOWER HOSE (8) with COUPLING NUT through SPRAY
HOLDER (6) and ESCUTCHEON (1). ( Note: SPRAY HOLDER (6)
must be separate from ESCUTCHEON (1) to get HOSE (8)
thrrough ESCUTCHEON (1).] Install SEAL (9) and connect both
HOSES (8) and (10). INSTALL second SEAL (9) and connect
HAND SHOWER (11) to SPRAY HOSE (8).
When not in use, HANDSHOWER should be seated
in the HOLDER.
NOTE
6
1
2
3
4
5
7
8
10
9
9
11
6
M968595 Rev.1.2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
Hex wench
(supplied)
Before the bathroom is completely finished, you may
want to remove spout, handshower, and handles to
avoid damage during construction.
To remove handles, reverse steps in section 4.
To remove SPOUT (1), proceed as follows:
Unthread LIFT ROD KNOB (2) to release it from the
TRANSFER ROD (8). Remove LIFT ROD KNOB (2). VIEW A.
Remove PLUG BUTTON (3) and remove SET SCREW (4)
using 4mm hex wrench supplied.
Lift SPOUT (1) off SHANK (5) carefully and remove RUBBER
RING (6).
Unthread SHANK SLEEVE (7) and remove from SHANK (5).
Reverse sequence to re-install SPOUT (1). Be sure RUBBER
RING (6) is properly seated in its recess at the base of the
SPOUT (1). Make certain SET SCREW (4) is properly aligned
and tight so that SPOUT (1) is locked in place.
1
8
8
3
4
6
5
7
VIEW "A"
VIEW "A"
7MAKE WATER SUPPLY CONNECTIONS
8
7A
With HANDLES in OFF position, turn on
WATER SUPPLIES and check all connections
for leaks.
Operate both HANDLES to flush water lines
thoroughly.
Connect HOT water supply to LEFT INLET
UNION (1) and COLD water supply to
RIGHT INLET UNION (2). Pipe connections
are 3/4" NPT. Use sealant or Teflon tape
on pipe connections.
Do not solder directly to valve body.
TEST INSTALLED FAUCET
3/4" X 3/4" NPT UNION
(NOT SUPPLIED)
HOT
COLD
3/4" NPT
HAND
SHOWER
TRANSFER KNOB
3/4" NPT
2
1
Lift HAND SHOWER from HOLDER, direct spray
into tub. Lift TRANSFER KNOB to check HAND
SHOWER and HOSES for leaks.
Turn handles "off" and replace HAND SHOWER.
IMPORTANT: It is strongly recommended that access be
provided for all enclosed mechanical parts to this system.
2
FIG. 1

028679-0070A
TUBE & TEE
ASSEMBLY
012668-0070A
SHANK KIT
030274-0070A
SHANK
MOUNTING KIT
M911810-0070A
RUBBER RING
012078-0070A
VALVE COUPLING KIT
M962616-YYY0A
HAND SHOWER
HOLDER
028699-0070A
COUPLING (FOR TRANSFER)
M910830-0070A
STREAM STRAIGHTENER
028667-0020A
HAND SHOWER HOSE
033760-0070A
HAND SHOWER SEAL KIT
051343-0070A
HOSE KIT
030275-0070A
SHANK SLEEVE KIT
030278-0070A
TRANSFER
SEAL KIT
M962616-YYY0A
SPOUT KIT (7010.901)
M962615-YYY0A
SPOUT KIT (7010.900)
MODEL NUMBER
7010.900
7010.901
028698-0070A
COUPLING
(LESS SPRAY)
M968595 Rev.1.2
M952454-0070A
TRANSFER
ROD ASSEMBLY
M962578-YYY0A
BUTTON AND SCREW
607676-YYY0A
PLUG BUTTON
DECK-MOUNT BATH FILLER
GREEN TEA
CHROME
STAINLESS STEEL
002
075
Replace the "YYY" with
appropriate finish code
A950646-YYY0A
HAND SHOWER
M961634-0070A
VALVE MTG. KIT
994053-0070A
CARTRIDGE
M962619-0070A
DECK ADAPTER KIT
A918049-0070A
ADAPTER
A918555-0070A
HANDLE SCREW
M950171-YYY0A
HANDLE KIT
M962575-YYY0A
TRANSFER KNOB
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-12-00
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
HOT LINE FOR HELP