American Standard Dazzle 6028.240 User manual

M968491 Rev. 1.2
6028.240
DAZZLE
WRENCH
Certified to comply with ANSI A112.18.1
Installation
Instructions
Mini Spread Lavatory Faucet with
Speed Connect Drain*
Adjustable WrenchScrewdriver Channel Locks
Recommended tools
Tubing Cutter
1INSTALL FAUCET
SINK OR
MOUNTING
SURFACE
POP-UP
CABLE
Turn off hot and cold water
supplies before beginning.
CAUTION
SINK
5/16'' MIN.
SLOT
Insert SPOUT (1) through center hole of mounting surface, making sure the
SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6)
onto SPOUT SHANK (7) from under side of sink . Make sure SPOUT (1)
is centered in the sink hole, the slot in the BRASS WASHER (5) is in
back and the O-RING (8) is seated at the end of SHANK (7).
Tighten LOCKNUT (6) on SPOUT (1) firmly. Fig. A.
Drop LIFT ROD (12) through hole in SPOUT (7) and thread ROD
END (13) into the TAB (14) in the VALVE BODY (5). Fig. C.
Install the valve LOCKNUT (1), FRICTION WASHER (2) and RUBBER
WASHER (3) onto the two VALVE SHANKS (4) if not already installed.
The LABEL indicating the front of the fitting faces the front of the sink.
Insert VALVE BODY (5) through holes from under side of SINK. Threads
of both VALVE SHANKS (4) should extent at least 5/16 inch above SINK
top. Fig. B. Be sure SHANK (9) and O-RING (6) of SPOUT (7) is pushed
into TEE (8) section of the VALVE BODY (5). Fig. C.
Install ESCUTCHEONS (10) with RUBBER RINGS (11) and screw
ESCUTCHEONS (10) onto VALVE SHANKS (4) until snug against
internal stop. Adjust LOCKNUTS (1) downward if necessary.
Tighten LOCKNUTS (1) on VALVE SHANKS (4) firmly to secure fitting.
1a INSTALL VALVE BODY
2
1
3
4
3
6
10 5
11
10
11 2
1
5
6
7
7
8
SINK
FRONT
8
14
13
4
9
12
1
FRONT
Fig. A.
Fig. B.
Fig. C.
Speed Connect Drain*
• 1/3 of the parts, installs in 1/3 of the time
• No tools needed
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain. Helpful tips for
removing your current drain can be found in the Troubleshooting section of these instructions.

M968491 Rev. 1.2
6
POP-UP KNOB (1) must be fully down. Fig. B.
FLANGE GASKET AND POP-UP KNOB DOWN
Check DRAIN FLANGE in SINK to ensure that
WHITE FOAM GASKET (3) is fully compressed
and not visible. Fig. A.
Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body. Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3). Fig. B.
POP-UP DRAIN
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
2
4
3
2
TIGHTEN LOCKNUT
1
REMOVE FLANGE
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
2
3
1
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.
INSTALL DRAIN FROM
BELOW FIXTURE 5
From under side of SINK
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the SINK.
Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above SINK and tighten
FLANGE (4) firmly.
4
Fig. B.
Fig. A. Fig. B.
2
DRAIN
OUTLET
1
3
4
REAR OF SINK
DRAIN
FLANGE
Fig. A. Fig. B.
WHITE FOAM
GASKET
NOT VISIBLE
2
3
1
Fig. A.
1
DRAIN
BODY
4

M968491 Rev. 1.2
9MAKE WATER SUPPLY AND WASTE CONNECTIONS
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED
AND MUST BE PURCHASED SEPARATELY.
HOT COLD
1/2" PIPE THREAD
3/8 COMPRESSION
CONNECTION
Thread CABLE CONNECTOR (1) clockwise
onto DRAIN BODY CONNECTION (2) and
hand tighten. Fig. A.
Your new POP-UP DRAIN installation is
now complete. Fig. B.
Note: Tailpeice on pop-up drain is 1-1/4” O.D.
Fig. B.
Fig. A.
ATTACH CABLE CONNECTOR
7
2
1
Operate LIFT KNOB (1) to verify that STOPPER (2) opens and
closes.
Note: If STOPPER (2) does not open and close properly then
refer to the “troubleshooting section” of these instructions.
CHECK OPERATION OF POP-UP
8
Fig. B.
1-1/4” O.D.
2
FRONT
Connect water supply to FAUCET (1) with 1/2" IPS FLEXIBLE SUPPLIES
(3) or 3/8" O.D. BULL-NOSE RISERS (4).
Use adjustable wrench to tighten connections. Do not over tighten.
Be careful not to kink copper supply when bending. Use tubing cutter
to cut to proper length.
Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to
waste outlet.
3
1
2
FERRULE
COUPLING NUT
1/2" IPS
FLEXIBLE SUPPLIES
3/8"O.D.
BULL-NOSE RISERS
3
1

M968491 Rev. 1.2
6
10a TEST INSTALLED FITTING
With HANDLES (3) in OFF position, turn on WATER
SUPPLIES (6) and check all connections for leaks.
Remove AERATOR (7).
Operate both HANDLES (3) to flush water lines thoroughly.
Replace AERATOR (7).
9
6
1
2
3
5
6
4
CHECK DRAIN CONNECTIONS
Operate POP-UP KNOB (8) and fill lavatory with water.
Check that DRAIN STOPPER (9) makes a good seal
and retains water in SINK. If DRAIN STOPPER (9)
does not seal properly, please refer to Troubleshooting
section in these instructions.
Release POP-UP KNOB (8) down and check all drain
connections and "P" trap for leaks. Tighten
if necessary.
12
WASTE
OUTLET
SERVICE
11
To change direction of handle rotation, proceed as follows:
Turn valve to OFF position.
Pull out INDEX CAP (1) and remove HANDLE SCREW (2).
Pull off HANDLE (3) and ADAPTER (4).
Remove SPRING CLIP (5).
Lift STOP WASHER (6), turn 90˚ and replace.
Replace SPRING CLIP (5).
Replace ADAPTER (4), HANDLE (3), SCREW (2), and INDEX CAP (1).
AERATOR may accumulate dirt causing distorted and reduced water
flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON position.
Do not force - handles turn only 90˚.
“P” TRAP
7
4
8
90˚
10
Turn VALVE into OFF position.
Push ADAPTER (1) into VALVE STEM (2).
Align HANDLE (3) and install onto ADAPTER (1).
Install HANDLE SCREW (4) and tighten to secure
HANDLE (3).
Insert INDEX BUTTON (5).
INSTALL HANDLES
5
4
3
1
2
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:

M968491 Rev. 1.2
Speed Connect™ Drain
Troubleshooting Guide
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
The Stopper can now be removed by lifting it out of the Drain. Fig. F.
CAM
CAM CAP
CABLE ADJUSTMENT PROCEDURE
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
Fig. B.Fig. A. Fig. C.
REMOVE
CAM
Fig. E. Fig. F.
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
STOPPER REMOVAL PROCEDURE
2
1
RE-ATTACH
DISCONNECT
Fig. D.
REMOVE
CAM CAP
5
DOWN
STOPPER

LOGO
DRAIN
Unlocked Mode
Fig. H.
LOOP TOWARD
FRONT OF SINK
180˚
M968491 Rev. 1.2
STOPPER INSTALLATION PROCEDURE
Locked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink and the American Standard logo is facing front. Rotate
Stopper slightly if necessary so that the Stopper slides all the
way down.Fig. G.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
Unlocked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink and the American Standard logo is facing rear. Rotate Stopper
slightly if necessary so that the Stopper slides all the way down.
Fig. H.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
Fig. J. Fig. K.
INSTALL
CAM CAP
CAM
INSTALL CAM
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Locked Mode
(Vandal Proof)
6
LOGO
DRAIN
LOOP TOWARD
REAR OF SINK
Fig. G.