American Standard Jasmine 3821.6XX User manual

Installation
Instructions
M968188 REV. 1.1
Certified to comply with ANSI A112.18.1M
3821.6XX
8
AB
1INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
SPOUT BASE
Assemble RUBBER WASHER (5), BRASS WASHER (6), and threaded LOCKNUT (7) onto SHANK (4) from underside
of sink or mounting surface. Hand tighten LOCKNUT (7) and check that rotation of HANDLE (8) from HOT to COLD
is centered.
Push O-RING (11) onto SPOUT SHANK (4). Make certain the O-RING (11) is properly seated in recess of DECORATIVE
FLANGE (10).
Insert SUPPLY HOSES (3) and SHANK (4) through mounting hole and seat DECORATIVE FLANGE (10) onto sink or
mounting surface.
Use a screwdriver to tighten SCREWS (9) on LOCKNUT (7). Work your way around LOCKNUT (7), tightening
the screws slightly each time until all are snug to ensure even pressure.
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON (1). Insert supply
HOSES (3) and SHANK (4) through hole of ESCUTCHEON (1) and mounting surface. Make certain the O-RING (2)
is properly seated in recess of SPOUT BASE. Follow mounting instructions below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Remove ESCUTCHEON (1) , feed FAUCET HOSES (3) and SHANK (4) through
DECORATIVE FLANGE (10). Push FLANGE (10) so the raised step fits into recess of SPOUT BASE.
10
8
1
PUTTY
4
SINK OR
MOUNTING
SURFACE
11
3
4
3
2
0
1
2
3
4
5
6
5
6
7
9
5
6
7
9
SINGLE CONTROL KITCHEN
FAUCET AND CAST SPOUT
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
TOOLS REQUIRED
Plumbers' Putty or Caulking
Adjustable WrenchChannel Locks Regular Screwdriver
Phillips ScrewdriverPhillips Screwdriver
Turn off water at
main supply.
CAUTION

M968188 REV. 1.1
On model with separate spray, place the
SPRAY HOLDER (1) into the appropriate mounting
hole. Assemble the SPRAY HOLDER WING NUT (2)
onto the shank of SPRAY HOLDER (1) from below
and tighten. Do not use putty.
On model with spray through the ESCUTCHEON (3),
place SPRAY HOLDER (4) into the hole of ESCUTCHEON (3).
Assemble SPRAY HOLDER NUT (5) onto the shank of
SPRAY HOLDER (4) from below and tighten.
Do not use putty.
For installation less spray, cap off SPRAY HOSE
CONNECTION with PIPE CAP (6).
3INSTALL SPRAY HOLDER
1
3
56
42
4CONNECT HOSE SPRAY
3
4
1
2
Feed SPRAY HOSE (1) through SPRAY HOLDER (2)
and attach COUPLING NUT (3) of HOSE (1) to
HOSE ADAPTOR (4) on valve body. Tighten
COUPLING NUT (3) firmly.
SPRAY HOSE
CONNECTION
2MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply to Hot (Marked with a Red Line)
and right supply to Cold wall supply. Use
adjustable wrench to tighten connections.
Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
0
1
2
3
4
5
6
1
2
COLD
HOT

M968188 REV. 1.1
5TEST INSTALLED FAUCET
Move HANDLE down into "off" position and remove AERATOR.
Turn on water supplies and check connections for leaks.
Operate HANDLE up and down, left and right to flush water
lines thoroughly.
For faucet with spray, direct SPRAY HEAD into sink and
activate SPRAY. Check hose connections for leaks.
Move HANDLE down to "off" position and replace AERATOR.
AERATOR
CHECK CONNECTIONS
FOR LEAKS
Spout leakage. If fitting leaks above or below SPOUT HUB remove SPOUT as follows
and check SPOUT O-RINGS and SPACER O-RINGS.
Loosen SET SCREW (1). Pull HANDLE (2) off valve stem.
Remove CAP (3) and and RETAINER (4). Loosen CARTRIDGE SCREWS (5) and
remove CARTRIDGE (6).
Pull off SPACER (7) and O-RINGS (8).
Remove SPOUT (11) by pulling up gently while moving SPOUT (11) side to side.
Check both SPOUT O-RINGS (10). Replace if necessary.
On models with SPRAYS, DIVERTER (9) can be cleaned by pulling
DIVERTER (9) out of the MANIFOLD (12). Clean DIVERTER (9) and
MANIFOLD (12). Push DIVERTER (9) back into MANIFOLD (12).
Reverse procedure to reinstall SPOUT, CARTRIDGE and HANDLE.
Loosen HANDLE SCREW (1) and remove HANDLE (2).
Remove ESCUTCHEON CAP (3). unscrew the three CARTRIDGE SCREWS (5).
Clean inlets of CARTRIDGE (6) and MANIFOLD (12).
Reassemble CARTRIDGE (6), alternately tightening SCREWS (5). Replace CAP (3) and HANDLE (2). Check flow.
SERVICE
6
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
Reduced flow. If the flow gradually reduces over a number of months, the AERATOR
may have collected debris. To clean, remove AERATOR and rinse with water and
remove any debris. Turn on faucet to wash any debris out of the faucet. Thread
AERATOR back into spout. Operate faucet.
2
1
6
10
12
11
3
4
5
7
9
8
HANDLE
SPRAY
AERATOR
SPOUT
HUB
6
PRY RED RING FORWARD
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
"A"
"A"
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
"B"
"RED RING"- HOT
LIMIT SAFETY STOP
TEMPERATURE
SETTING NUMBERS
0
1
2
3
4
5
6
5
By restricting handle rotation and limiting the amount of hot water allowed
to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental
scalding. To set the maximum hot water temperature of your faucets, all you
need to do is adjust the setting on the HOT LIMIT SAFETY STOP.
Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull
HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade
screwdriver or your fingers to pull up and rotate red
HOT LIMIT SAFETY STOP (5). Follow Step "A" or "B" to adjust
min./max.discharge temperature. "0" being the hottest to
"7" the coldest temperature setting. Factory set at "0".
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten
HANDLE SCREW (1) and install INDEX BUTTON (2).
HOT LIMIT SAFETY STOP ADJUSTMENT
"B"