American Standard Hampton 2770.702 Series User manual

BAR SINK FAUCETS
Installation
Instructions
Certified to comply with ANSI A112.18.1M
U.S. Patent No. 5,819,789
2770.732 SERIES
2770.712 SERIES
2770.702 SERIES
PORCELAIN
LEVER
HANDLE
METAL
LEVER
HANDLE
END
CAP
INDEX CAP
HANDLE
SCREW
HANDLE
SCREW
HANDLE
BASE
HANDLE
BASE
(CROSS HANDLE)
LOCKNUT
SUPPLY
NUT
ADAPTER
PUTTY
PLATE
INDEX
CAP
PORCELAIN
CROSS
HANDLE
CARTRIDGE
ESCUTCHEON
AERATOR
SPOUT
CLIP
SPOUT
O-RING
.3&7
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1-800 442-1902
Weekdays 8:00 a.m. to 8:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 1998
IN MEXICO 01-800-839-12-00
with EverClean™ Finish
Congratulations on purchasing your American Standard
faucet with EverClean finish found only on American
Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
EverClean Finish
• One wipe effortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these finishes)

TEST INSTALLED FAUCET
2
Remove AERATOR.
With handles in OFF position, turn on water supplies and check all connections for leaks.
Operate both handles to flush water lines thoroughly.
Turn handles into OFF position and replace AERATOR.
1INSTALL FAUCET
Turn off hot and cold water supplies before beginning.
CAUTION
Place faucet in position on sink.
Assemble and tighten LOCKNUTS from underside of SINK.
Connect the HOT water supply to the left SHANK and the
COLD water supply to the right SHANK using appropriate
connectors and sealant (not supplied), and COUPLING NUTS.
LOCKNUT
HOT
COLD
COUPLING NUT
PUTTY
PLATE
BODY
SINK
SHANK
NOT SUPPLIED
Check alignment, if not satisfactory
aligned;
Push out ADAPTER carefully.
Turn ADAPTER either 45˚ or 90˚
so that male square on
ADAPTER catches different
female square in HANDLE BASE.
Assemble and tighten
MOUNTING SCREW.
Push INDEX CAP in top of
HANDLE.
SERVICE Handle alignment.
3
To change direction of handle rotation,
proceed as follows:
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90$.
SPRING
CLIP
STOP
WASHER
90$
Turn valve to OFF position.
Pull out INDEX CAP and remove
HANDLE SCREW.
Pull off HANDLE BASE and remove
ADAPTER.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90$and replace.
Replace SPRING CLIP.
Reinstall HANDLE.
VALVE
STEM
FEMALE SQUARE
IN HANDLE BASE
HANDLE
ADAPTER
SQUARE
4EverClean™ Finish Care Instructions
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with
clean water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
.3&7