American Standard Heritage Amarilis 4800 SERIES User manual

SPREAD LAVATORY
FAUCETS
Installation
Instructions
34312M-D
Printed in Mexico
4800 SERIES
4801 SERIES
4802 SERIES
7830 SERIES
7831 SERIES
7890 SERIES
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
U.S. Patent No. 5,819,789
Turn off hot and cold water
supplies before beginning.
CAUTION
EXTENSION
AERATOR
SEAL
WASHERS
COUPLING
NUT
O-RING
CONVENTIONAL
SPOUT LESS POP-UP
4800 SERIES
WRENCH
LIFT
ROD
4801
SERIES
HERITAGE
SPOUT
W/POP-UP
RUBBER
WASHER
RETAINER
LOCKNUT
TUBE & TEE
ASSEMBLY
THUMBSCREW
HANDLE
SCREW
CARTRIDGE
ESCUTCHEON
RUBBER
RING
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
VALVE
ASSEMBLY
SPOUT ASSEMBLY (Model 7890 only)
O-RING
SCREW
RUBBER
GASKET
GOOSENECK SPOUT
WITH POP-UP
7831 SERIES
HERITAGE SERIES
GOOSENECK SPOUT
BAR SINK
7890 SERIES
1
Apply the grease (provided) liberally to the
SPOUT O-RINGS and SNAP RING areas.
Assemble the SPOUT and tighten SPOUT NUT
until snug on VALVE BODY.
Tighten BRASS LOCKNUT on center body.
SPOUT
SPOUT
NUT
SNAP
RING
SPOUT
O-RINGS
ESCUTCHEON
STOPPER
FLANGE
DRAIN
GASKET
DRAIN
WASHER
DRAIN
NUT
DRAIN
BODY
EXTENSION
ROD
CLIP
PIVOT
ROD
TAILPIECE

Product names listed herein are trademarks of American Standard Inc.
© American Standard Inc. 1999
SERVICE
1
6
LOCKNUT
SPOUT
CARTRIDGE
SCREEN
SPRING
CLIP
STOP
WASHER
RETAINER
RUBBER
WASHER
RUBBER
GASKET
SINK
Insert BASE or SPOUT shank through
center hole of SINK, making sure
RUBBER GASKET is properly positioned.
Assemble RUBBER WASHER,
RETAINER, and LOCKNUT onto
threads of SPOUT from underside
of SINK.
Insert LIFT ROD through SPOUT (or
BASE) and slot of RETAINER.
Align SPOUT and tighten LOCKNUT.
Be sure slot in BRASS WASHER is
positioned to the rear as shown.
Push SCREW into TEE and tighten SCREW
onto SHANK to secure SPOUT connection.
TEST INSTALLED FAUCET
5Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Operate LIFT ROD and check DRAIN for leaks.
Turn handles into OFF position and replace AERATOR.
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90°and replace.
Replace SPRING CLIP.
Replace ADAPTER, HANDLE, SCREW, and INSERT.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove INSERT and HANDLE SCREW.
Slip HANDLE with ADAPTER off.
Unscrew CARTRIDGE with wrench.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace ADAPTER, HANDLE, SCREW,
and INSERT.
TEE
SCREW
O-RING
O-RING
Apply a bead of PUTTY around underside
of DRAIN PLUG flange. Insert DRAIN
PLUG into SINK drain hole.
SHANK
Place WASHERS inside COUPLING NUTS
and connect HOSE to each valve outlet.
Tighten COUPLING NUTS.
Connect HOT water supply to the left VALVE
and the COLD water to the right VALVE using
sealant and appropriate connectors and
coupling nuts.
Refer to separate "Instruction Sheet" for assembly of handles.
Hold DRAIN PLUG to prevent turning
and assemble GASKET, WASHER, and
LOCKNUT, from underneath sink.
Insert threaded end of TAILPIECE
into lower end of DRAIN PLUG.
Connect other end to trap.
DRAIN ASSEMBLY
(Model 4802 only)
3
SPOUT OR BASE ASSEMBLY (continued)
TAIL
PIECE
PUTTY
FLANGE
DRAIN
PLUG
RUBBER
GASKET WASHER
LOCKNUT
SINK
34312M-D
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 7:00 p.m. Eastern Time
Saturdays 8:00 a.m. to 4:00 p.m. Eastern Time
INSTALL POP-UP DRAIN
4STOPPER
Push TAILPIECE down into TRAP
(threaded end up).
Thread LOCKNUT, WASHER and
GASKET onto DRAIN BODY.
Apply a bead of PUTTY to underside
of FLANGE.
Feed DRAIN BODY up through SINK
and thread FLANGE fully onto BODY.
Tighten LOCKNUT firmly, keeping the
PIVOT ROD pointed towards the back
of the SINK.
Drop STOPPER into DRAIN BODY.
Pull TAILPIECE up and thread tightly
into DRAIN BODY.
Position EXTENSION ROD onto POP-UP
ROD and tighten THUMBSCREW.
Remove one end of CLIP from PIVOT ROD
by squeezing ends together while sliding.
Insert PIVOT ROD into second or third hole
in EXTENSION and reassemble CLIP.
(EXTENSION may need to be bent.)
Adjust STOPPER height by repositioning
EXTENSION and tightening THUMBSCREW.
FLANGE
SINK
GASKET
PUTTY
WASHER
LOCKNUT
TAILPIECE
TRAP
CLIP
PIVOT
ROD
VALVE INSTALLATION
2Insert VALVE BODY through hole from
underside of SINK. Thread of VALVE
BODY should extend at least 5/16 inch
above SINK top. If necessary, adjust
LOCKNUT.
Place RUBBER RING into ESCUTCHEON
and screw ESCUTCHEON onto VALVE
BODY until snug against internal stop.
Set VALVE BODIES so that their outlets
are facing toward center of SINK.
Tighten LOCKNUT using wrench supplied
with faucet.
Before connecting TEE make certain
that O-RINGS are properly seated on
stepped SHANK and SCREW.
LEDGE
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
VALVE
BODY
5/16''
MIN.
ESCUTCHEON
RUBBER
RING
PIVOT
ROD
DRAIN
BODY TAILPIECE CLIP
THUMBSCREW POP-UP ROD
EXTENSION
ROD
TRAP
EXTENSION
ROD