American Standard Monterrey 6500 Series User manual

SPREAD LAVATORY
FAUCETS
Installation
Instructions
Printed in Mexico
6500 SERIES
6501 SERIES
6502 SERIES
6900 SERIES
6901 SERIES
6902 SERIES
6530 SERIES
6531 SERIES
6532 SERIES
6930 SERIES
6931 SERIES
6932 SERIES
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
US PATENT D371956
AERATOR
COUPLING
NUT
O-RING
LIFT
ROD
SPOUT
W/POP-UP
RUBBER
WASHER
RETAINER
LOCKNUT
TUBE & TEE
ASSEMBLY
HANDLE
SCREW
LEVER
HANDLE
CARTRIDGE
ESCUTCHEON
RUBBER
RING
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
VALVE
ASSEMBLY
O-RING
SCREW
RUBBER
GASKET
SEAL
COMPRESSION
NUT
FRICTION
RING
60186B
BONNET
NUT
WRIST BLADE
HANDLE
INDEX
STOPPER
FLANGE
DRAIN
GASKET
DRAIN
WASHER
DRAIN
NUT
DRAIN
BODY
EXTENSION
CLIP
PIVOT
ROD
TAILPIECE

Turn off hot and cold water
supplies before beginning.
CAUTION VALVE INSTALLATION
DRAIN INSTALLATION
12
4
LEDGE
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
VALVE
BODY
5/16''
MIN.
ESCUTCHEON
RUBBER
RING
LOCKNUT
SPOUT
RETAINER
RUBBER
WASHER
RUBBER
GASKET
SINK
Insert BASE or SPOUT shank through
center hole of SINK, making sure
RUBBER GASKET is properly positioned.
SPOUT OR BASE ASSEMBLY
Assemble RUBBER WASHER,
RETAINER, and LOCKNUT onto
threads of SPOUT from underside
of SINK.
Insert LIFT ROD through SPOUT (or
BASE) and slot of RETAINER.
Align SPOUT and tighten LOCKNUT.
Be sure slot in BRASS WASHER is
positioned to the rear as shown.
Prepare TUBE and TEE ASSEMBLY to fit
available VALVE location. If necessary, cut
and/or bend TUBING carefully. Make sure
tube bend is close to the TEE so that it
will not effect the compression joint at
the VALVE.
Place RUBBER RING into ESCUTCHEON
and screw ESCUTCHEON onto VALVE
BODY until snug against internal stop.
Tighten LOCKNUT to secure VALVE
position. Attach COUPLING to TEE
and tighten.
TAIL
PIECE
TEST INSTALLED FAUCET
5Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Operate LIFT ROD and check DRAIN for leaks.
Turn handles into OFF position and replace AERATOR.
TEE
SCREW
O-RING
O-RING Apply a bead of PUTTY around underside
of DRAIN PLUG flange. Insert DRAIN
PLUG into SINK drain hole.
SHANK
Remove COUPLING NUT, FRICTION RING,
and RUBBER FERRULE from each valve and
slide onto tubing.
Push TUBING ends into VALVE side outlets. Insert
VALVES into mounting holes from underside of SINK.
Press TEE onto SHANK of SPOUT making certain that the
SHANK O-RING is properly seated on SHANK.
Slide RUBBER FERRULE, FRICTION RING,
and COUPLING NUT to outlet of VALVE
and tighten COUPLING NUT firmly.
Repeat on other VALVE.
Connect HOT water supply to inlet of left
VALVE and COLD water supply to inlet of
right VALVE using appropriate connector.
Hold DRAIN PLUG to prevent turning
and assemble GASKET, WASHER, and
LOCKNUT, from underneath sink.
Insert threaded end of TAILPIECE
into lower end of DRAIN PLUG.
Connect other end to trap.
DRAIN ASSEMBLY
(Models 6502, 6902, 6532
and 6932)
(Models 6801 and 6831 only)
PUTTY FLANGE
DRAIN
PLUG
RUBBER
GASKET WASHER
LOCKNUT
SINK
3
VALVE INSTALLATION (continued)
60186B
STOPPER
Push TAILPIECE down into TRAP
(threaded end up).
Thread LOCKNUT, WASHER and
GASKET onto DRAIN BODY.
Apply a bead of PUTTY to underside
of FLANGE.
Feed DRAIN BODY up through SINK
and thread FLANGE fully onto BODY.
Tighten LOCKNUT firmly, keeping the
PIVOT ROD pointed towards the back
of the SINK.
Drop STOPPER into DRAIN BODY.
Pull TAILPIECE up and thread tightly
into DRAIN BODY.
Position EXTENSION ROD onto POP-UP
ROD and tighten THUMBSCREW.
Remove one end of CLIP from PIVOT ROD
by squeezing ends together while sliding.
Insert PIVOT ROD into second or third hole
in EXTENSION and reassemble CLIP.
(EXTENSION may need to be bent.)
Adjust STOPPER height by repositioning
EXTENSION and tightening THUMBSCREW.
FLANGE
SINK
GASKET PIVOT
ROD
DRAIN
BODY
PUTTY
WASHER
LOCKNUT
TAILPIECE
TRAP
TAILPIECE
CLIP
THUMBSCREW POP-UP ROD
CLIP
PIVOT
ROD
EXTENSION ROD
SERVICE
6
CARTRIDGE
SCREEN
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove HANDLE and BONNET NUT.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90°and replace.
Replace SPRING CLIP.
Replace BONNET NUT, HANDLE, SCREW,
and INDEX.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove HANDLE and BONNET NUT.
Remove CARTRIDGE by pulling up.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace BONNET NUT, HANDLE, SCREW
and INDEX.
SPRING
CLIP
STOP
WASHER
90°
Product names listed herein are trademarks of American Standard Inc.
American Standard Inc. 1997
C
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time