American Standard QUINCE 4433.150F15 User manual

1INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
1
99
3
B
A
PUTTY
(IF REQUIRED)
SINK OR
MOUNTING
SURFACE
SPOUT BASE
2
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6).
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
Plumbers' Putty or CaulkingAdjustable WrenchPhillips Screwdriver
RECOMMENDED TOOLS
Regular Screwdriver
Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
Turn off water at
main supply.
CAUTION
3
2
4
5
8
6
7
4
5
8
6
7
SINGLE CONTROL KITCHEN
PULL-OUT FAUCET
Installation
Instructions
Certified to comply with ANSI A112.18.1M
4433.150
QUINCE™
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
M965245 REV. 1.2
(A) Installation with ESCUTCHEON (1).Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Make certain the SEAL (9) is properly seated in recess of faucet body. Insert SUPPLY HOSES (2), SPRAY HOSE (7)
and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface. Follow mounting instructions
below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (9)
is properly seated in recess of faucet body.Insert supply HOSES (2), SPRAY HOSE (7) and SHANK (3) through mounting
hole and seat SPOUT BASE onto sink or mounting surface. Do not use putty.
4433.150F15

2MAKE WATER SUPPLY CONNECTIONS
3CONNECT SPRAY HOSE AND INSTALL WEIGHTS
With PULL-OUT SPRAY (1) seated in FAUCET (2),
install WEIGHTS (3) onto HOSE (4) using SCREW (5).
Locate the WEIGHT (3) two feet (2') from the
underside of the sink deck.Tighten SCREW (5) firmly.
Make sure SEAL WASHER (7) is installed in COUPLING
NUT (6). Connect threaded end of HOSE (4) to SPRAY HOSE
COUPLING NUT (6) from fitting. Use wrench to tighten.
1
2
COLD
HOT
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply (Marked with a Red Stripe) to Hot
and right supply (Marked with Blue Stripe) to
Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
Faucet supplies are 21" long from faucet base.
Note: If additional supply length is
required, installer must purchase
additional parts separately.
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
4
6
7
2
CHECK CONNECTIONS FOR LEAKS.
Move HANDLE (1) into the "off" position.
Turn on water supplies and check connections
for leaks.
CHECK CONNECTIONS
FOR LEAKS
4
1
1
M965245 REV. 1.2
53
24"

7
5TEST INSTALLED FAUCET
SPRAY OPERATION
With FAUCET on, press TOGGLE BUTTON (6) on
SPRAY (3) to switch from stream to spray.
CARE:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
STREAM (AERATOR)
SPRAY
1
36
Move HANDLE (1) into "off" position.
With HANDLE (1) in "off" position, pull HAND SPRAY (2) from SPOUT (3). SPRAY HOSE (4) should pull
approximately 2 feet and direct open SPRAY END (5) into sink.
Operate handle up and down, in COLD and HOT positions,
to flush water lines thoroughly.
Check HAND SPRAY (2) operation:
SERVICE
6
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
1
2
4
If Faucet Drips Proceed As Follows:
Turn VALVE in OFF position.
If faucet drips, operate HANDLE several times from OFF to ON position.
Do not apply excessive force.
FLOW CONTROL DEVICE may accumulate dirt. To remove the FLOW
CONTROL DEVICE, unthread SPRAY AND HOSE ASSEMBLY and
rinse clean FLOW CONTROL DEVICE.
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2)
and remove HANDLE (3).
Unthread ESCUTCHEON CAP (4). Unthread three MOUNTING
SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7) and remove CARTRIDGE
SEALS (8).
Place SEALS (8) into CARTRIDGE PORTS (6a).
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten
HANDLE SCREW (1) and install INDEX BUTTON (2).
Test fitting.
Clean MANIFOLD (7), CARTRIDGE (6) ports and SEALS (8).
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten
MOUNTING SCREWS (5) alternately.
5
6
8
7
6a
5
3
4
2
FLOW CONTROL
DEVICE
SPRAY AND HOSE
ASSEMBLY
M965245 REV. 1.2
3

QUINCE™
MODEL NUMBER
A911836-0070A
SEAL
M962806-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962146-0070A
MOUNTING KIT
CHROME
STAINLESS STEEL
OIL RUBBED BRONZE
002
075
224
Replace the YYY with
Appropriate finish code
M918506-0070A
CARTRIDGE SCREWS
M964176-YYY0A
HANDLE KIT
A951470-0070A
CARTRIDGE
M907306-YYY0A
ESCUTCHEON CAP
M962294-0070A
BUTTON AND
SCREW KIT
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2012
HOT LINE FOR HELP
M952244-YYY220A (2.2 GPM)
SPRAY WITH HOSE
M952244-YYY150A (1.5 GPM)
SPRAY WITH HOSE
M965245 REV. 1.2
SINGLE CONTROL
KITCHEN
PULL-OUT FAUCET
M964395-0070A
WEIGHT
4433.150
4433.150F15