American Standard Townsquare 2555.400 User manual

Installation
Instructions
Certified to comply with ASME A112.18.1M
U.S. Patent No. 5,819,789
Roughing-in Dimensions
DRAIN INSTALLATION

Replace UPPER GASKET (7) and FRICTION RING (10).
Position the side threaded outlet rearward and secure by
tightening MOUNTING NUT (9). Thread ESCUTCHEON (5)
onto TRANSFER VALVE (8) until it seats against the
BIDET LEDGE.
STOPPER
Thread LOCKNUT (6), WASHER (7) and
GASKET (8) onto DRAIN BODY (5).
Apply a bead of PUTTY to underside
of FLANGE (9).
Feed DRAIN BODY (5) up through BIDET
and thread FLANGE (9) fully onto
BODY (5).
Tighten LOCKNUT (6) firmly, keeping the
PIVOT ROD (3) pointed towards the back
of the BIDET.
Place STOPPER into drain and assemble
O-RING (1), WASHER (2), PIVOT ROD (3)
and NUT (4) to DRAIN BODY (5). Concave
side of cup WASHER (2) is toward ball.
Push DRAIN ESCUTCHEON (10) onto
TAILPIECE (11).
BIDET
PUTTY
CLIP
4
9
3
1
4
11
6
5
8
72
10
2555.400
10
BIDET FITTING
.3&7
TOWN SQUARE
*Wrench
*Supplied with Fitting
*Hex key
Flat Blade Screwdriver
Adjustable Wrench
Channel Locks
Phillips Screwdriver
Required Tools
5VCJOH$VUUFS
Turn off hot and cold water
supplies before beginning.
CAUTION
BIDET FAUCET INSTALLATION
Assemble MOUNTING NUTS with RUBBER WASHERS (1)
onto the VALVE BODIES (2) and insert VALVE BODIES (2)
through outside holes, from underside of the BIDET
LEDGE. Drop the RUBBER RING (3) over the VALVE
BODIES (2) and screw on the ESCUTCHEON (4) until it
locks against the internal stop.
Tighten the MOUNTING NUT (1) to secure the
VALVE BODY (2).
Remove ESCUTCHEON (5), FRICTION RING (10) and
UPPER GASKET (7) from TRANSFER VALVE (8) and
insert into the center forward hole of BIDET.
COLD
HOT
BIDET
LEDGE
3
2
7
8
1
9
5
BIDET OUTLINE
IS SYMBOLIC
FINISHED
WALL
1-1/4 O.D. TAILPIECE
DOUCHE
SPRAY 2-1/8
DIA.
ADJ. 1-1/4
TO 2-1/4
3-7/8
5-1/2
1-3/8
DIA.
7/8 DIA.
TRANSFER VALVE
(FOR FLUSHING
RIM OR SPRAY)
FINISHED
FLOOR
DIVERTER
ASSEMBLY
1-1/4 MAX.
1-3/16 DIA.
(C) (H)
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
8 TO 12
2-1/4
DIA.
Congratulations on purchasing your American Standard faucet
with EverClean nish found only on American Standard faucets.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
with EverClean™ Finish
EverClean Finish
• One wipe eortlessly removes spots
• Eliminates the need for cleaners and scrubbing
• Permanent surface protectant remains beautiful
for the life of the faucet
• EverClean™ available on: Polished Chrome, Satin Nickel,
Stainless Steel, Polished Brass (or any combination of these nishes)


Unscrew LIFT ROD NUT (1) from LIFT ROD GUIDE (2).
Make sure SEAL (3) is seated into ESCUTCHEON
of LIFT ROD GUIDE (2).
Drop LIFT ROD GUIDE (2) into rear hole of bidet and
from below secure with ROD GUIDE NUT (1).
WATER SUPPLY CONNECTIONS

Connect water supplies to FITTING (1) with 1/2" IPS
FLEXIBLE SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3).
Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply
when bending. Use tubing cutter to cut to proper length.
NOTE: FLEXIBLE SUPPLIES ARE NOT INCLUDED AND HAVE TO BE
PURCHASED SEPARATELY.
Cold
Hot FERRULE
COUPLING NUT
3
1
2
.3&7
LIFT ROD GUIDE INSTALLATION
SPRAY INSTALLATION

Assemble SPRAY BODY (1) to BIDET.
Using putty, seal underside of SPRAY
BODY FLANGE (2) and secure with
NUT (3).
Thread SPRAY CAP (9) onto SPRAY BODY (1).
Thread SPRAY HOSE (4) with SEAL
WASHER (5) to SPRAY BODY (1).
Connect other end of HOSE (4) with
SEAL WASHER (6) to bottom outlet
NIPPLE (7) of the TRANSFER VALVE (8).
Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2)
to side of TRANSFER VALVE (3)
Install SEAL (4) into coupling nut of TEE (5) and
tighten connection to ADAPTER (2)
Connect HOSE COUPLING NUTS (6) to Hot
and Cold valve bodies and securely tighten.
TEE AND HOSE CONNECTION

Front
3
1
2
4
5
6
6
1
3
2
4
PUTTY
6
2
7
8
1
3
5
9

FINISH DRAIN INSTALLATION
Position EXTENSION ROD (1) onto POP-UP ROD (2) and tighten
THUMBSCREW (3).
Position BIDET fixture and secure to floor.
Insert lift rod into lift rod guide.
Using metal TAILPIECE (5), make connection to the TRAP (6).
Remove one end of CLIP (4) from PIVOT ROD (7) by squeezing ends
together while sliding.
Insert PIVOT ROD (7) into second or third hole in EXTENSION ROD (1)
and reassemble CLIP (4). (EXTENSION ROD (1) may need to be bent.)
Adjust STOPPER height by repositioning EXTENSION ROD (1) on POP-UP
ROD (2) and tightening THUMBSCREW (3).
3
1
17
4
6
5
2
INSTALL HANDLES
1
2
3
4
5
6
7
10
Figure B
Figure A
Figure D
Figure C
4
5
6
10
5
10
8
Turn VALVE to OFF position.
Figure A: Install STEM ADAPTERS (7) onto VALVE STEMS (8).
Figure B: With colored side up, place FRICTION RING (6) over
DECK ADAPTER (10). Loosely screw FRICTION NUT (5) onto
DECK ADAPTER (10). Do not tighten. Align flats on FRICTION
NUT (5) with RIBS (9) in HANDLE BASE (4).
Figure C: Screw HANDLE BASE (4) with FRICTION NUT (5)
onto DECK ADAPTER (10) until snug against mounting surface
and aligned properly.
Figure D: Install LEVER HANDLE (3) onto HANDLE ADAPTER (7)
and align. Check alignment, if not satisfactory remove and align.
Insert HANDLE SCREW (2) and tighten. Press in
INDEX BUTTON (1).
9
4
FLATS
ALIGNED
.3&7
INSTALL DIVERTER KNOB
B
12
15
14
13
11
Diverter Knob; Push DIVERTER KNOB (11)
onto HANDLE ADAPTER (12). Push on RING (13)
and tighten with SCREW (14). Press on KNOB
CAP (15). (The screwdriver Gap for
disassembling should face downwards).

SERVICE
To change direction of handle rotation, proceed
as follows:
Turn valve to OFF position.
Remove HANDLE and ADAPTER if present.
Remove SPRING CLIP (1).
Lift STOP WASHER (2), turn 90pand replace.
Replace SPRING CLIP (1).
Replace HANDLE ASSEMBLY.
Replace SPRAY (3) and operate handles several times from
OFF to ON position. Do not force, handles turn only 90˚.
SPRAY (3) may accumulate dirt causing distorted and reduced
water flow. Unscrew and remove SPRAY (3) and rinse clean.
.3&7
90p
1
2
3
Operate Lift Rod (3) and fill Bidet with water. Check that DRAIN
STOPPER (4) makes a good seal and retains water in Bidet.
Adjust stopper height by repositioning Lift Rod (3) with
EXTENSION ROD (6) and tightening Thumbscrew (5).
Release DRAIN STOPPER (4) and check all drain connections
for leaks. Tighten if necessary.
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2)
and check all connections for leaks.
Operate both handles to flush water lines thoroughly.
Turn diverter to rim wash and bidet spray.


1
3
3
6
5
4
2
2
American Standard’s EverClean finish will wipe clean with a soft, dry cloth. A soft cloth with clean
water may also be used, if desired. No additional cleaning products are required.
DO NOT USE: Soaps, acid, polish, abrasives, harsh cleaners, or a cloth with a coarse surface.
EverClean™ Finish Care Instructions