American Standard SERIN 2064.4 User manual

M968924 Rev.1.3
2064.400
SERIN™
35
4
4
Certified to comply with ANSI A112.18.1
Installation
Instructions
Bidet Faucet and Transfer Valve with
Speed Connect™ Drain
Turn off hot and cold water
supplies before beginning.
CAUTION
1BIDET FAUCET INSTALLATION
Replace UPPER GASKET (8) and WASHER (7) and
ESCUTCHEON (6) until it locks against internal stop.
Position the side threaded outlet rearward and
secure MOUNTING NUT (11).
Remove ESCUTCHEON (6), WASHER (7) and
UPPER GASKET (8) from TRANSFER VALVE (9).
Insert TRANSFER VALVE (9) into the center forward
hole of BIDET.
COLD
HOT
BIDET
LEDGE
10
4
3a
3
8
9
1
5
2
6
Roughing-in
Dimensions
SPRAY INSTALLATION
2
Assemble SPRAY BODY (1) to BIDET. Using putty, seal underside
of SPRAY BODY FLANGE (2) and secure with NUT (3).
Thread SPRAY CAP (9) onto SPRAY BODY (1).
Thread SPRAY HOSE (4) with SEAL WASHER (5) to SPRAY BODY (1).
Connect other end of HOSE (4) with SEAL WASHER (6) to side outlet
NIPPLE (7) of the TRANSFER VALVE (8).
PUTTY
6
2
7
8
1
9
Tighten LOCKNUTS (1) with WRENCH (5) (supplied)
to secure VALVE BODIES (3, 3a).
Install LOCKNUT (1) and RUBBER WASHER (2) onto VALVE BODIES (3, 3a). From
under side of mounting surface, install VALVE BODY (3, 3a) through valve mounting
holes. Threads of VALVE BODY (3, 3a) should extent at least 5/16 of a inch above
mounting surface top. Fig. A. Thread ESCUTCHEON (4) onto VALVE BODIES
(3, 3a) until snug against internal stop. If necessary, adjust LOCKNUT (1).
Place RUBBER RING (10) into ESCUTCHEON (4).
MOUNTING
SURFACE
4
10
2
1
3, 3a
5/16''
MIN.
Fig. A.
11
Adjustable Wrench
Screwdriver
Channel Locks
Recommended tools
Tubing Cutter
Phillips Screwdriver
Plumbers' Putty or
Caulking
BIDET OUTLINE
IS SYMBOLIC
FINISHED
FLOOR
FINISHED
WALL
1-1/4 O.D. TAILPIECE
DOUCHE
SPRAY 2-1/8
DIA.
ADJ. 1-1/4
TO 2-1/4
3-7/8
5-1/2
1-3/8
DIA.
7/8 DIA.
1-1/4
MAX.
1-3/16
DIA.
2-1/4
DIA.
(C) (H)
4-1/4
FOR GROUND JOINT
CONNECTION OR 1/2 "
O.D. SLIP (INLETS)
REAR VIEW WITH
WALL REMOVED
TRANSFER VALVE
(FOR FLUSHING
RIM OR SPRAY)
8 TO 12
7
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only on
American Standard faucets.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.

M968924 Rev.1.3
POP-UP DRAIN
Tighten TAILPIECE (4) on DRAIN BODY before
installing DRAIN BODY. Fig. B.
7
3
5
4
FLANGE GASKET
Check DRAIN FLANGE in BIDET to ensure that WHITE
FOAM GASKET (1) is fully compressed and not visible.
Fig. A. DRAIN
FLANGE
1WHITE FOAM
GASKET
NOT VISIBLE
Insert LIFT ROD GUIDE (1) and CABLE CONNECTOR (2)
through rear hole, making sure SEAL WASHER (3) is
properly seated. Fig. B.
From below slip slot in MOUNTING NUT (4) over CABLE (5).
Thread NUT (4) onto lift rod guide shank to secure ROD
GUIDE (1) to bidet. Hand tighten only. Fig. B.
1
2
4
3
ILLUSTRATION
SHOWN LESS
VALVES
SLOTTED
MOUNTING
NUT
POP-UP ROD ASSEMBLY
TIGHTEN LOCKNUT
1
Fig. A. Fig. B.
REMOVE FLANGE
Remove CLEAR PLASTIC COVER (1).
Remove CARDBOARD SPACER (2) from under
DRAIN POP-UP (3).
2
3
1
Tighten LOCKNUT (1) firmly with Adjustable
Wrench or Channel Locks.
2
INSTALL DRAIN FROM
BELOW FIXTURE 6
From under side of BIDET
install DRAIN BODY (1) up
through drain outlet.
Note: No plumber’s putty
or caulk is required.
The CABLE ATTACHMENT
POINT (2) must face towards
the rear of the BIDET.
DRAIN
OUTLET
Install FOAM GASKET (3) and
FLANGE (4) onto drain body
from above BIDET and tighten
FLANGE (4) firmly.
1
4
3
4
Fig. B.
Fig. A. Fig. B.
2
3
1
Fig. A.
Thread FLANGE (1) counter-clockwise and remove
FLANGE (1) and FOAM GASKET (2) from drain
body. Fig. A.
Thread LOCKNUT (3) clock-wise to bottom of
drain body. Push GASKET (4) down against
LOCKNUT (3). Fig. B.
DRAIN
BODY
4

M968924 Rev.1.3
Connect HOT water supply to inlet of left SHANK and COLD
water supply to right SHANK using sealant, appropriate
connectors, and COUPLING NUTS.
Connect 1-1/4” O.D. tailpiece on POP-UP DRAIN to
waste outlet.
10
Connect water supply to VALVE BODIES (7,7a) with
1/2" IPS FLEXIBLE SUPPLIES (8) or 3/8" O.D. BULL-NOSE
RISERS (9). Use adjustable wrench to tighten connections.
Do not over tighten. Be careful not to kink copper supply when
bending. Use tubing cutter to cut to proper length.
TEE AND HOSE CONNECTION
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT
INCLUDED AND MUST BE PURCHASED SEPARATELY.
HOT
COLD
FLEXIBLE
SUPPLIES
1
1/2" PIPE
THREAD
3/8 COMPRESSION
CONNECTION
2
POP-UP KNOB (1) must be fully
down. Fig. A.
Thread CABLE CONNECTOR (1)
clockwise onto DRAIN BODY
CONNECTION (2) and hand
tighten. Fig. B.
Your new POP-UP DRAIN
installation is now complete.
Fig. C.
Note: Tailpeice on pop-up drain
is 1-1/4” O.D. Fig. C.
Fig. B.
ATTACH CABLE
CONNECTOR
8
Operate LIFT KNOB (1) to verify that STOPPER (2)
opens and closes.
Note: If STOPPER (2) does not open and close properly
then refer to the “troubleshooting section” of these
instructions.
CHECK OPERATION OF POP-UP
INSTALL DIVERTER KNOB
9
Fig. C.
1-1/4” O.D.
1
1
5
3
1
2
2
WATER SUPPLY CONNECTION
Insert SEAL (1) into ADAPTER (2) and tighten ADAPTER (2) to
side of TRANSFER VALVE (3).
Install SEAL (4) into coupling nut of TEE (5) and tighten
connection to ADAPTER (2).
Connect HOSE COUPLING NUTS (6) to Hot and Cold valve
bodies and securely tighten.
6
7
7a
6
9
Front
Push DIVERTER KNOB (1) onto HANDLE ADAPTER (2).
Push on RING (3) and tighten with SCREW (4).
Press on KNOB CAP (5).
Note: Screwdriver gap is for disassembling and should
point downwards.
4
2
COMPRESSION
NUT
COUPLING
NUT
OUTLINE OF BIDET
3/8 O.D.
BULL-NOSE
RISERS
CONNECT TO
WASTE OUTLET
2
3
4
5
FERRULE
DOWN
Fig. A.

M968924 Rev.1.3
CHECK DRAIN CONNECTIONS
12
11
13
14 15
TEST INSTALLED FITTING
With HANDLES (1) in OFF position, turn on WATER
SUPPLIES (2) and check all connections for leaks.
Operate both HANDLES (1) to flush water
lines thoroughly.
Rotate TRANSFER VALVE (5) from rim wash to
spray several times to check operation.
SERVICE
Pull up POP-UP KNOB (3) and fill Bidet with water. Check
that DRAIN STOPPER (4) makes a good seal and retains
water in Bidet. If STOPPER (4) does not seal properly,
please refer to “Troubleshooting Guide” in these instructions.
Push POP-UP KNOB (3) down and check all drain
connections and "P" trap for leaks. Tighten
if necessary.
1
1
4
SPRAY
OUTLINE OF BIDET
2
2
3
UNTHREAD
INSTALL HANDLES
1
2
4
5
3
TOP
Figure "A"
SPLINE END DOWN
Push ADAPTER (1) on VALVE STEM (2), so that the hole of the
ADAPTER (1) without a spline is facing up. See figure "A". Tighten
STEM SCREW (3) to secure ADAPTER (1).
Find correct position of LEVER HANDLE ASSEMBLY (4) by adjusting
male teeth on ADAPTER (1) to female teeth in HANDLE (4).
Thread LEVER HANDLE ASSEMBLY (4) onto ESCUTCHEON (5)
until snug against mounting surface.
THREAD ON
TO DECK
ADAPTER
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Thread counter-clock wise HANDLE BASE (1) to remove
HANDLE ASSEMBLY (2) from ESCUTCHEON BASE (3).
Use a flat blade screw driver to remove SPRING CLIP (4).
Lift STOP WASHER (5), turn 90˚ and replace.
Replace SPRING CLIP (4).
Reinstall HANDLE ASSEMBLY (2).
If spout drips, operate handles several times from OFF
to ON position. Do not force - handles turn only 90˚.
90˚
VALVE
1
5
3
4
2
DO: SIMPLY RINSE THE PRODUCT
CLEAN WITH CLEAR WATER. DRY
WITH A SOFT COTTON FLANNEL
CLOTH.
DO NOT: DO NOT CLEAN THE
PRODUCT WITH SOAPS, ACID,
POLISH, ABRASIVES, HARSH
CLEANERS, OR A CLOTH WITH
A COARSE SURFACE.
CARE INSTRUCTIONS:

M968924 Rev.1.3
Speed Connect™ Drain
Troubleshooting Guide
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled
as “Cam” and “Cam Cap” in the illustration. Fig. B.
Use fingers or small screwdriver under either side of the Cam Cap to pry it out from the Drain. Fig. D.
Remove the Cam by pulling it straight out while wiggling gently to loosen the Rubber Seal. Fig. E.
The Stopper can now be removed by lifting it out of the Drain. Fig. F.
CAM
CAM CAP
CABLE ADJUSTMENT PROCEDURE
If sink does not hold water even though Stopper is in the “down” position:
• Follow CABLE ADJUSTMENT PROCEDURE.
If Stopper does not raise up fully or sink drains too slowly:
• Follow CABLE ADJUSTMENT PROCEDURE.
If you need to remove the Stopper:
• Follow STOPPER REMOVAL PROCEDURE.
If you would like the ability to remove your Stopper simply by lifting it out of the drain:
• Follow STOPPER INSTALLATION PROCEDURE for “Unlocked” mode.
Fig. B.
REMOVE
CAM
Fig. E.
Disconnect the Cable from the Drain by threading the Cable Connector (1) counter-clockwise. Fig. A.
Look at the area on the Drain Body where the Cable was attached and locate the component labeled as
“Cam” in the illustration. Fig. B.
Use a small screwdriver to rotate the Cam in the clockwise direction as far as it will go. At this point the
Stopper should be in the UP position. Fig. B, C.
Push DOWN on the Lift-Knob to make sure it is fully down. Fig. C.
Re-attach the Cable to the Drain Body Connection (2) by threading the Cable Connector (1) clockwise onto the
Drain Body Connection (2) and hand-tighten. Fig. A.
STOPPER REMOVAL PROCEDURE
2
11
RE-ATTACH
DISCONNECT
Fig. D.
REMOVE
CAM CAP
Fig. C.
STOPPER
Fig. F.
Fig. A. DOWN

M968924 Rev.1.3
STOPPER INSTALLATION PROCEDURE
Locked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. G.
To install the stopper in “Locked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the rear of the
Sink and the American Standard logo is facing front. Rotate
Stopper slightly if necessary so that the Stopper slides all the
way down.Fig. G.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
Troubling Shooting Guide to complete installation. Stopper will be
in “Locked” mode and not be removable.
Unlocked Mode:
Look at the Plastic Loop at the bottom of the Stopper and notice
that the Loop is on one side of the Stopper. Fig. H.
To install the stopper in “Unlocked” mode, insert the Stopper into
the Drain so that the Plastic Loop is facing toward the front of the
Sink and the American Standard logo is facing rear. Rotate Stopper
slightly if necessary so that the Stopper slides all the way down.
Fig. H.
Re-install the Cam into the Drain, rotating the Cam if necessary
to make sure it is fully inserted. Fig. J.
Re-install the Cam Cap, making sure the guide teeth are facing
outward. If the Cam Cap does not “snap” into place, then rotate
the Cam to make sure it is fully inserted. Fig. K.
Re-attach Cable. See “CABLE ADJUSTMENT PROCEDURE” in
“Troublingshooting Guide” to complete installation. Stopper will be
in “Unlocked” mode and removable.
Fig. J. Fig. K.
INSTALL
CAM CAP
CAM
INSTALL CAM
The Stopper can be installed two ways, “Locked” Mode (Stopper cannot be
removed) or “Unlock” Mode (Stopper is removable).
Locked Mode
(Vandal Proof)
180˚
LOGO
DRAIN
Fig. H.
LOOP TOWARD
FRONT OF BIDET
Unlocked Mode
LOGO
DRAIN
Fig. G.
LOOP TOWARD
REAR OF BIDET

M968924 Rev.1.3
024220-0070A
COUPLING NUT
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2008
060463-0070A
ADAPTER KIT
033772-0070A
TEE AND HOSE KIT
(INCLUDING SEALS)
923348-0070A
HANDLE ADAPTER
030281-0070A
TRANSFER VALVE
MOUNTING KIT
028645-YYY0A
BIDET SPRAY
953800-0070A
TRANSFER VALVE
918428-0070A
HANDLE SCREW
M962182-YYYOA
HANDLE
030257-YYYOA
ESCUTCHEON KIT
M961634-0070A
VALVE MTG. KIT
918555-0070A
HANDLE SCREW
918049-0070A
ADAPTER
994053-0070A
CARTRIDGE
MODEL NUMBERS
2064.400
BIDET FITTING
SERIN™
CHROME 002
SATIN NICKEL 295
Replace the "YYY" with
appropriate finish code
028646-0070A
SPRAY HOSE
CONNECTION KIT
7
IN MEXICO 01-800-839-12-00
M952426-YYY0A
DRAIN ASSEMBLY
M962457-007A
FLANGE
ASSEMBLY
M962552-0070A
CAM ASSEMBLY
M962458-0070A
DRAIN MOUNTING KIT
M913207-0070A
TAILPIECE INSERT
M952430-0070A
CABLE ASSEMBLY
M962463-0020A
TAILPIECE & ESCUTCHEON
M922872-0070A
CAM SEAT INSERT
M950245-YYY0A
HANDLE ASSEMBLY
M962414-YYY0A
ESCUTCHEON KIT
M962508-YYY0A
POP-UP ROD
M962481-YYY0A
LIFT ROD GUIDE
M962544-YYY0A
STOPPER
ASSEMBLY