American Standard SERIN 2064.15 Series User manual

1
© 2017 AS America Inc.
Installation Instructions
Certied to comply with ASME A112.18.1
© 2017 AS America, Inc.
NOTE TO INSTALLER: Please give this manual to the customer after installation.
To learn more about American Standard Selectronic®Products visit our website at: www.americanstandard-us.com
or e-mail us at: [e-mail]
For Parts, Service, Warranty or other Assistance,
please call (844) CRT-TEAM / [phone] (In Canada: 1-800-387-0369)
(In Toronto Area only: 1-905-306-1093)
SERIN™
Deck Mount Electronic
Proximity Lavatory Faucet
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.
Optional 206P400.XXX, 4" Deck Plate
Optional 206P800.XXX, 8" Deck Plate
Product No’.s & Options 1
Specications 2
Faucet Installation 2-3
Electrical Installation 4-6
Start-up / Maintenance 7-8
FAQ’s / Troubleshooting 8-9
Replacement Parts 10
M965612 Rev. 1.8 (12/17)
MODEL NUMBERS
2064.14X 2064.15X 206B.10X

2
Thank you for selecting American-Standard...the benchmark of ne quality for over 100 years.To ensure that your
installation proceeds smoothly--please read these instructions carefully before you begin.
Remove the tting and loose items from the carton. The illustration below shows all the ttings and loose items after they
have been removed from the carton. Some items may be packaged partially assembled to other items.
UNPACKING All American Standard Products Are Water Tested At Our Factory.
Some Residual Water May Remain In The Valve During Shipping.
1. Installation Instructions
2. Spout Assembly
3. Mounting Kit
4. Control Box
5. Supply Hose
6. 4" Deck plate (optional, must be ordered separately)
7. 8" Deck plate (optional, must be ordered separately)
8. Mixing Valve (optional, must be ordered separately)
9. Control Box Cover Screws
206P400.XXX
206P800.XXX
605XTMV1070
PRODUCT No.s
2
3
1
6
7
8
5
4
Spout
All 2064. SERIES
Installation Instructions
SERIN™
Deck Mount Electronic
Proximity Lavatory Faucet
Certified to comply with ASME A112.18.1
© 2014American Standard
Product No.'s& Options
Specications
FaucetInstallation
Electrical Installation
Start-up / Maintenance
FAQ’s / Troubleshooting
Replacement Parts
1
2
2-3
4-6
7-8
8-9
10
Optional206P400.XXX, 4" Deck Plate
Optional206P800.XXX, 8" Deck Plate
NOTETO INSTALLER: Please give this manual tothe customer after installation.NOTETO INSTALLER: Please give this manual tothe customer after installation.
Tolearn more about American Standard Selectronic®Products visit our websiteat: www.americanstandard-us.com
or e-mail us at: [email protected]
For Parts,Ser vice,Warranty or other Assistance,
please call (844) CRT-TEAM/ [phone] (In Canada: 1-800-387-0369)
(InToronto Area only: 1-905-306-1093)
CAUTION: Useonly American Standard supplied
transformersand cable sets. Using non-AS
supplied cables,or cutting, splicing or modifying
any components will voidthe warranty.
9
MODEL NUMBERS
2064.14X 2064.15X 206B.10X
Deck Plate Mixing ValveBase Product
Plug-In AC
Power Kit
Hard-Wired AC
Power Kit
Multi-AC
Power Kit
PK00.PAC PK00.HAC PK00.MAC
POWER KITS SOLD SEPARATELY
M965612 Rev. 1.8 (12/17)

3
1SPOUT ASSEMBLY
INSTALLATION; Fig. 1
1. Make sure O-RING (3) is installed into groove in
ESCUTCHEON RING (4).
2. Insert SENSOR CABLES (1), SPOUT HOSE (5) and
SPOUT SHANK (6) through center hole of mounting
surface. Fig. 1.
3. Assemble RUBBER WASHER (7), BRASS WASHER (8)
and LOCKNUT (9) onto SHANK (6) from underside of
sink or mounting surface. Hand tighten LOCKNUT (9).
4. Use a screwdriver to tighten SCREWS (10) on
LOCKNUT (9). Work your way around LOCKNUT (9),
tightening the screws slightly each time until all are
snug to ensure even pressure.
Note: 4"and 8”Deck Plates (11) are available for other
installations, see page one for information.
5. When using optional 4" or 8" DECK PLATE (11) rst
thread the DECK PLATE CENTERING NUT (12) onto
SHANK (6). Thread the DECK PLATE CENTERING
NUT (12) tight against the underside of the faucet base.
6. Follow steps 1-4 above for the spout installation.
Roughing-in Dimensions
1. Slip Joint Pliers
2. Adjustable Wrench
3. Plumbers’ Putty or
Caulking
4. Phillips Screwdriver
5. Flat Blade Screwdriver
6. Electric Drill & 1/4"
Drill Bit
7. Tape Measure
1
2
3
4
5
6
7
10'
M965612 Rev. 1.8 (12/17)
114mm
(4-1/2")
500mm
(20") 1524mm
(60")
413mm
(16-1/4")
3/8" COMP.
32mm
(1-1/4") DIA. 125mm
(4-7/8")
81mm
(3-3/16")
MOUNTING
SURFACE
(249mm)
9-3/4"
(173mm)
6-11/16"
(100mm)
3-15/16"
(136mm)
5-3/8"
(177mm)
7"
RECOMENDED CONTROL BOX OR
EQUIVALENT BY OTHERS
HARD-WIRED AC ONLY 10' MAX. CABLE LENGTH
4"(102mm) SQ. X 3-1/2"(89mm) DEEP CONTROL BOX
Hubbel-RACO #256 OR EQUAL (BY OTHERS).
GENERAL DESCRIPTION:
Electronic faucet with proximity operation. Vandal resistant solid brass construction
single post mounting. Operates on DC (battery/power pack) or AC permanent power
(plug-in/hardwire). In-line strainer for solenoid is integral. Single inlet 3/8 compression,
built-in check valves, and exible stainless steel 16-1/4" reach inlet hose for spout
connection.
Note: All plumbing and electrical wiring must be installed in accordance
with applicable codes, regulations and standards.
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.
RECOMMENDED TOOLS
CAUTION Turn off hot and cold water
supplies before beginning Fig. 1
2
11
*12
4
3
1
SENSOR
CABLES
5
7
8
9
10
PUTTY
(If required)
IMPORTANT:Do not
use putty when installing
faucet without escutcheon.
MOUNTING
SURFACE
*(#12 CENTERING NUT) is
only used with the
installation of a 4"or 8"
deck plate
6

4
2MOUNT CONTROL BOX; Fig. 4
Important: For AC installation, make sure power
supply connector is inserted into control box
through power supply grommet before control box
is mounted to the wall. Reference electrical
installation section (pages 5 & 6).
1. Determine location of CONTROL BOX (3). It must be
located with-in the 14" (356mm) by 21" (533mm)
shaded area shown in Figure 4 in order for electrical
connections from the spout assembly to be made.
NOTE: CONTROL BOX SUPPLY HOSE is 20". Distance
between wall supply and CONTROL BOX (3) must be
taken into consideration.
2. Remove tape from CONTROL BOX COVER (1)
and pull off COVER (1). Hold the CONTROL BOX (3)
in desired location and mark the four mounting hole
locations as shown. Fig. 4.
NOTE: Find plastic bag containing 4 M5X16 screws to be
used for securing the CONTROL BOX COVER (1) when
installation is complete.
NOTE: For AC installation, make power supply
connection before mounting CONTROL BOX (3) to wall.
3. It is recommended that the CONTROL BOX (3) be
secured to a wall stud or cross brace within the wall
using the SCREWS (16) supplied. If the CONTROL BOX
(3) is to be installed on tile or plaster walls, the
ANCHORS (17) and SCREWS (16) should be used.
3CONNECT SPOUT HOSE TO
CONTROL BOX; Fig. 5
1. Connect SUPPLY NUT (18) from spout hose to nipple
on top of CONTROL BOX (3). Tighten with adjustable
wrench to make a water tight connection. Fig. 3.
4
CONNECT WATER SUPPLY TO
CONTROL BOX AND WALL
SUPPLY; Fig. 6, 6a
NOTE; If using the optional Mixing Valve See Sheet
#M968808 for installation instructions.
1. Insert FIBER WASHER (19) into SUPPLY NUT (18) on
CONTROL BOX (3).
2. Connect FLEXIBLE SUPPLY HOSE (20) to SUPPLY NUT
(18) on CONTROL BOX (3). Tighten to make a water tight
connection. Use two wrenches to tighten if necessary. Fig. 6.
3. Connect FLEXIBLE SUPPLY HOSE (20) directly to wall
supply. Connection on FLEXIBLE SUPPLY HOSE (20) is
3/8" compression. Use adjustable wrench to tighten
connection. Do not over tighten. Fig. 6a.
Note: FLEXIBLE SUPPLY HOSE (20) measures 20"from the
bottom of the CONTROL BOX (3) base. If additional supply
length is required, installer must purchase parts separately.
Important: If FLEXIBLE SUPPLY HOSE (20) is too long, loop
to avoid kinking.
M965612 Rev. 1.8 (12/17)
Fig. 4
1524mm
(60")
14"
(356mm)
3-3/4"
(96mm)
2-3/4"
(71mm)
3"
(76mm)
21"
(mm)
1
17
16
3
20"
(500mm)
MOUNTING HOLES
SUPPLIES
WASTE
ENCLOSURE
MOUNTING
HOLES
LAVATORY RIM OR
MOUNTING SURFACE
Fig. 5
18
3
18
3
20
Fig. 6
3
COLD WATER OR
TEMPERED
WALL SUPPLY
Fig. 6a
19
!

5M965612 Rev. 1.8 (12/17)
ELECTRICAL INSTALLATION
Fig. 1a Fig. 1b
Fig. 1
Fig. 1c
5a
7
2
Fig. 1d
2
3
1
4
5
INSTALL BATTERY
STANDARD
BATTERY
STANDARD
BATTERY
PWRX
PWRX
CR-P2
5a
5a
5a
6
5
ADC VERSIONS (PWRX & STANDARD
BATTERY); Fig. 1
1. Remove CONTROL BOX COVER (1). Fig. 1.
2. Feed the SENSOR CABLES (2) through the top of
CONTROL BOX (3). Fig. 1a.
3. Insert BATTERY (4) into BATTERY HOLDER (5), make
sure the shape of the BATTERY (4) follows the shape
of the BATTERY HOLDER (5) and terminal end is
inserted rst. Fig. 1b.
4. Insert the BATTERY CONNECTOR (5a) for the Standard
Battery or PWRX Battery Pack through side GROMMET (6)
as shown. Fig. 1c.
5. Connect SOLENOID CABLE (7) and BATTERY
CONNECTOR (5a) to SENSOR CABLES (2). Place
Standard Battery or PWRX Battery Pack into Housing.
Fig. 1d.
6. Replace CONTROL BOX COVER (1). Tighten cover
screws rmly.
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.
Product Page
Plug-In AC Power Kit (PK00.PAC) 6
Hard-Wired AC Power Kit (PK00.HAC) 6
Multi-AC Power Kit (PK00.MAC) 7

6M965612 Rev. 1.8 (12/17)
Fig. 2
2
3 1
Fig. 2a
16 6
9
810
2
PLUG INTO
WALL OUTLET
7
Fig. 2c
BLACK & WHITE
POWER
CONNECTIONS
10' EXTENSION
13
12
10b
15
14
10a
7
2
2
Fig. 2b
6
9
FROM ELECTRICAL BOX
WITH POWER SUPPLY
16
B
AC VERSION; Fig. 2
• PLUG-IN
•HARDWARE
Note: For AC installation, make power supply connection
before mounting CONTROL BOX (3) to wall.
1. Remove CONTROL BOX COVER (1). Feed the
EXTENSION CABLES (2) from the Faucet through
the top of ENCLOSURE (3).
FOR AC PLUG-IN ONLY
2a. Insert POWER CORD (8) through POWER SUPPLY
GROMMET (9).Fig. 2a.
3a. Insert POWER CORD (8) through side GROMMET (6)
as shown. Fig. 2a.
4a. Connect one of the 27" EXTENSION CABLES (2) to
SOLENOID CABLE (7) and the other to the SINGLE AC
ADAPTER (10). Connect POWER CORD (8) to Single
AC Adapter (10) and install CONNECTOR LOCKING
DEVICE (16). Fig. 2a.
5a. Mount CONTROL BOX to wall. Replace CONTROL BOX
COVER (1). Tighten cover screws rmly.
6a. Plug AC POWER SUPPLY into wall outlet.
FOR HARDWIRE HOOK-UP ONLY
2b. Insert one end of the 10'EXTENSION (10a) through
POWER SUPPLY GROMMET (9). Fig. 2b.
3b. Insert 10'EXTENSION (10a) through side
GROMMET (6) as shown. Fig. 2b.
4b. Connect 27" EXTENSION CABLES (2) to SOLENOID
CABLE (7) and the other to the 10' EXTENSION
CABLE (10a). Install CONNECTOR LOCKING DEVICE
(16). Fig. 2b.
Contractor to supply ELECTRICAL BOX (12) and power
to POWER SUPPLY (13).
5b. Mount POWER SUPPLY (13) onto ELECTRICAL
BOX (12). Connect connections to POWER SUPPLY
CONNECTIONS (14). Fig. 2c.
6b. Connect the10'EXTENSION (10b) to the POWER
SUPPLY CABLE (15). Fig. 2c.
CAUTION Disconnect AC power supply
before opening CONTOL BOX.
CAUTION: Use only American Standard supplied cable sets.
Using non-AS supplied cables, or cutting, splicing or modifying
any components will void the warranty.

7M965612 Rev. 1.8 (12/17)
CFOR AC-VERSION
(MULTI HOOK-UP); Fig. 3, 3a, 3b
1. Remove COVERS from all CONTROL BOX (2).
2. Remove SOLID BLACK PLUG GROMMET (5) from
left side of all CONTROL BOX (2), except from Unit
#1. Replace with GRAY GROMMET (9). (Supplied with
each Faucet).
3. Feed SENSOR CABLES (2) through the top of
CONTROL BOX (3). Connect one SENSOR CABLE (2)
to the SOLENOID CABLE (7), and the other to either
of the two terminals at the one end of the Y-ADAPTER
(11). Connect the 10’ EXTENSION (10a) to the other
terminal at the same end of the Y-ADAPTER (11).
4. Feed the other end of the 10 ft. EXTENSION (10b)
through the two GRAY GROMMETS (6a and 6b)
and connect to the single terminal end of the next
unit’s Y-ADAPTER (11). Place Y-ADAPTER (11) into
CONTROL BOX (3).
5. Repeat Steps above for each additional Unit, for a
Max. of 15 Units on one AC POWER SUPPLY (7).
6. Replace CONTROL BOX COVERS. Tighten cover
screws rmly.
Unit #1 Detail
Fig. 3a
2
11
10b
AC POWER SUPPLY
2
SENSOR
CABLES
7
3
2
5
10b
10a
12
6a 6b
Fig. 3b
CAUTION: Use only American Standard supplied
transformers and cable sets. Using non-AS supplied
cables, or cutting, splicing or modifying any components
will void the warranty.
Unit #2 Unit #3
Fig. 3
10 ft.
EXTENSION
CABLE
AC POWER
SUPPLY
*MAXIMUM OF 15 UNITS PER AC POWER SUPPLY.
10' MAXIMUM CABLE LENGTH BETWEEN UNITS.
OR
Unit #1
Already installed
BLACK &
WHITE
POWER
CONNECTIONS

8M965612 Rev. 1.8 (12/17)
AHAND WASH SENSOR
OPERATION; Fig. 4
Prior to making power connection, make sure
detection zone is not obstructed. Sensor is self
adjusting. Keep detection zone clear for 15
seconds after power is connected.
When the Sensor detects a user, the water immediately
starts to ow. Water ow will stop 1.5 seconds after user is
out of sensor range. This comfort timer allows the user to
move his hands without the ow cycling on and off. As a
precaution, a safety timer will turn off the water after the
sensor has been blocked for 55 seconds. Water ow will
resume when the blockage is removed from the detection
zone and the sensor is activated again.
BHOW TO INSTALL AND CHANGE
BATTERY; Fig. 2
1. Remove COVER from CONTROL BOX (1).
2. Disconnect Battery Holder (3) from SENSOR
CABLE (5).
3. Remove old BATTERY from Battery Holder (3).
Install new BATTERY (2) making sure the terminal
side is inserted rst and shape of the battery
follows the shape of the BATTERY HOLDER (3).
Prior to making power connection, make sure
detection zone is not obstructed. Sensor is self
adjusting. Keep detection zone clear for 15
seconds after power is connected.
4. To change PWRX BATTERY PACK (4), unplug and
replace with new Power Pack.
5. Reconnect BATTERY HOLDER (3) to SENSOR CABLE (5).
6. Replace CONTROL BOX COVER. Tighten cover screws
rmly.
CHOW TO CLEAN FILTER
ASSEMBLY; Fig. 3
1. Remove CONTROL BOX COVER.
2. Close SUPPLY STOP (13) with 4mm Hex wrench.
Note: Activate sensor to keep water owing out of
faucet while shutting off.
3. Unthread FILTER ASSEMBLY (6) using a 7/16" socket.
4. Pull out the FILTER ASSEMBLY (6), remove and clean
white debris cup and lter screen.
5. Install the FILTER ASSEMBLY (6) back in its place and
tighten with a 7/16" socket.
Caution: Do not over tighten.
6. Open SUPPLY STOP (13) with 4mm Hex wrench.
7. Replace CONTROL BOX COVER. Tighten cover
screws rmly.
Fig. 1
DETECTION
ZONE:
BETWEEN
SPOUT AND
BASE OF SINK
Fig. 2
CR-P2
3
1
6
4
5
2
6
WHITE
DEBRIS
CUP
FILTER
SCREEN
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Fig. 3
7/16" SOCKET
4mm HEX WRENCH
13
START-UP / MAINTENANCE
CAUTION Before opening CONTROL BOX
disconnect AC power supply.
!
!

9M965612 Rev. 1.8 (12/17)
DHOW TO CLEAN AND REMOVE
THE AERATOR OR SPRAY; Fig. 4
1. Remove Aerator or Spray HOUSING (7) with
KEY supplied with faucet.
2. Remove Aerator or Spray (8) from HOUSING (7).
3. Clean the Aerator or Spray SCREEN (9).
4. Reassemble and install into spout end. Be sure the
black seal washer is in place.
EHOW TO CLEAN FLOW
REGULATOR; Fig. 5
1. Remove SUPPLY HOSE (1) from top of CONTROL
BOX ASSEMBLY (2). Pull out FLOW REGULATOR
(3) from CONTROL BOX ASSEMBLY (2).
2. Rinse clean FLOW REGULATOR (3). Reassemble
SUPPLY HOSE (1) to top of CONTROL BOX
ASSEMBLY (2).
FGENERAL CLEANING; Fig. 6
1. Only use a damp, soft cloth to clean the spout and
the sensor.
2. For tougher dirt, use a soft cloth with diluted dish
washing detergent. Wipe the area using a wet cloth
and dry using a soft cloth.
CAUTION
Do not scratch the sensor when cleaning.
Avoid using any abrasives or harsh detergents
or chemicals.
8
9
77
Fig. 4
KEY
2
3
3
Fig.5
1
RINSE CLEAN FLOW
REGULATOR (3)
Fig.6
FAQ’S
Q: How will I know if the battery needs to be replaced?
A: Valve will not open and sensor will continuously blink 2 times interrupted by a pause for up to 7 days.
Q: Why has the ow rate of the faucet reduced signicantly?
A: The lter assembly, ow regulator or areator/spray may be clogged. Check and clean.
Refer to Start-up/Maintenance, sections C, D and E.
Q: Why doesn’t the water ow out of faucet when I’m within the sensor detection zone?
A: Battery may need replacement. Check. If sensor continuously blinks 2 times interrupted by pause,
replace battery or call [phone].
Q: What is the normal operating pressure range?
A: Faucet will operate with supply pressures ranging from 20-80 psi.

10
HOT LINE FOR HELP
For toll-free information and answers to your questions, call:
(844) CRT-TEAM / [phone]
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of AS America, Inc. ©2017
To learn more about American Standard Selectronic® Products visit our website at:
www.americanstandard-us.com or e-mail us at: [email protected]
Mon. - Fri. 8:00 a.m. to 8:00 p.m. EST Saturday 10:00 a.m. to 4:00 p.m. EST
TROUBLESHOOTING FLOW CHARTS
UNIT DOES NOT FUNCTION
1 1
2 2
YES
YES
YES
NO
NO
NO
YES
NO
OPEN EXTERNAL SUPPLY STOPS.
OPEN INTERNAL SUPPLY STOP.
(HEX KEY NEEDED)
CRITICALLY LOW BATTERY.
INSTALL NEW BATTERY.
DEAD BATTERY. INSTALL
NEW BATTERY. REPEAT.
NO CHECK FOR DAMAGE TO SENSOR WIRE INSULATION.
REPLACE SENSOR.
ARE EXTERNAL SUPPLY
STOPS OPEN?
IS INTERNAL SUPPLY
STOP OPEN?
REPEATED DOUBLE FLASH
ON SENSOR?
RECONNECT BATTERY TO SENSOR.
DOES SENSOR FLASH FOR 5 SECONDS?
REPLACE SOLENOID
YES
YES
NO CHECK FOR DAMAGE TO SENSOR WIRE INSULATION.
REPLACE SENSOR.
RECONNECT BATTERY TO SENSOR.
DOES SENSOR FLASH FOR 5 SECONDS?
NO FULLY OPEN INTERNAL & EXTERNAL SUPPLY
STOPS BY TURNING COUNTER CLOCKWISE.
LOW FLOW COULD BE CAUSED BY DEBRIS
IN THE FILTER ASSEMBLY, FLOW REGULATOR
OR AERATOR/SPRAY. REMOVE, CLEAN AND
INSERT BACK TO ORIGINAL POSITION.
ARE INTERNAL & EXTERNAL SUPPLY
STOPS FULLY OPEN?
REPLACE SOLENOID
WATER IS CONTINUOUSLY RUNNING
LOW FLOW ISSUES
M965612 Rev. 1.8 (12/17)