American Standard 7500 Series User manual

CENTERSET LAVATORY FAUCETS
WITH GOOSENECK SPOUT
Installation
Instructions
60185
Printed in Mexico
7500 SERIES
7501 SERIES
7502 SERIES
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.
Certified to comply with ANSI A112.18.1M
PATENT PENDING
HANDLE
SCREW
BONNET
NUT
POP-UP
ROD
BODY
CARTRIDGE
SHANK
AERATOR
RUBBER
WASHER
BRASS
WASHER
LOCKNUT
COUPLING
NUT
STOPPER
FLANGE
DRAIN
GASKET
DRAIN
WASHER
DRAIN
NUT
DRAIN
BODY
EXTENSION
CLIP
PIVOT
ROD
TAILPIECE
GASKET
WRIST
BLADE
HANDLE
INDEX
LEVER
HANDLE
TAILPIECE
FLANGE
GRID DRAIN
POP-UP DRAIN
DRAIN
PLUG
RUBBER
GASKET WASHER
LOCKNUT

Product names listed herein are trademarks of American Standard Inc.
American Standard Inc. 1995
C
HOTLINE FOR HELP
For toll-free information and answers to your questions, call:
1 [phone]
Weekdays 8:00 a.m. to 4:00 p.m. Eastern Time
SERVICE
1
5
3
CARTRIDGE
SCREEN
TAIL
PIECE
TEST INSTALLED FAUCET
4Remove AERATOR.
With handle in OFF position, turn on water supplies and check
all connections for leaks.
Operate both handles to flush water lines thoroughly. Check
spout mounting and hose connections for leaks.
Operate LIFT ROD and check DRAIN for leaks.
Turn handles into OFF position and replace AERATOR.
To change direction of handle rotation,
proceed as follows:
Turn valve to OFF position.
Remove HANDLE and BONNET NUT.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90°and replace.
Replace SPRING CLIP.
Replace BONNET NUT, HANDLE, SCREW,
and INDEX.
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90°.
Plastic SCREEN in CARTRIDGE may accumulate
dirt causing reduced water flow. To clean, first
turn off hot and cold water supplies, then:
Remove HANDLE and BONNET NUT.
Remove CARTRIDGE by pulling up.
Thoroughly rinse plastic SCREEN at
base of CARTRIDGE.
Replace CARTRIDGE until flange is
tight against valve body.
Turn valves OFF.
Replace BONNET NUT, HANDLE, SCREW
and INDEX.
Apply a bead of PUTTY around underside
of DRAIN PLUG flange. Insert DRAIN
PLUG into SINK drain hole.
Hold DRAIN PLUG to prevent turning
and assemble GASKET, WASHER, and
LOCKNUT, from underneath sink.
Insert threaded end of TAILPIECE
into lower end of DRAIN PLUG.
Connect other end to trap.
GRID DRAIN ASSEMBLY
(Model 7502 only) PUTTY FLANGE
DRAIN
PLUG
RUBBER
GASKET WASHER
LOCKNUT
SINK
2
Asesemble GASKET to SHANKS and insert FAUCET SHANKS through holes of SINK.
Turn off hot and cold water
supplies before beginning.
CAUTION
Assemble RUBBER and BRASS WASHERS, and LOCKNUTS from underside of SINK. Drop
UPPER LIFT ROD through hole in BODY (models 7501 only), align BODY as far forward as possible
and secure position by tightening LOCKNUTS.
Connect the HOT water supply to the left SHANK and the COLD water supply to the right
SHANK using sealant, appropriate connectors, and COUPLING NUTS.
Unscrew SPOUT NUT and remove SPOUT.
To change spout to a swivel spout:
Take SPOUT CLIP off SPOUT and remove RUBBER RING.
Replace RUBBER RING with seperate PLASTIC RING packed with faucet.
Put SPOUT CLIP on SPOUT.
Reassemble SPOUT to BODY.
UPPER LIFT ROD
SHANK
BODY
SINK
SPOUT
SPOUT
NUT
RUBBER
RING
SPOUT
CLIP
PLASTIC
RING
RUBBER WASHER
BRASS WASHER
LOCKNUT
COUPLING NUT
HOT
COLD
GASKET
1/2" O.D. SLIP
60185
INSTALL POP-UP DRAIN (Model 7501 only) STOPPER
Push TAILPIECE down into TRAP
(threaded end up).
Thread LOCKNUT, WASHER and
GASKET onto DRAIN BODY.
Apply a bead of PUTTY to underside
of FLANGE.
Feed DRAIN BODY up through SINK
and thread FLANGE fully onto BODY.
Tighten LOCKNUT firmly, keeping the
PIVOT ROD pointed towards the back
of the SINK.
Drop STOPPER into DRAIN BODY.
Pull TAILPIECE up and thread tightly
into DRAIN BODY.
Position EXTENSION ROD onto POP-UP
ROD and tighten THUMBSCREW.
Remove one end of CLIP from PIVOT ROD
by squeezing ends together while sliding.
Insert PIVOT ROD into second or third hole
in EXTENSION and reassemble CLIP.
(EXTENSION may need to be bent.)
Adjust STOPPER height by repositioning
EXTENSION and tightening THUMBSCREW.
FLANGE
SINK
GASKET
PIVOT
ROD
DRAIN
BODY
PUTTY
WASHER
LOCKNUT
TAILPIECE
TRAP
TAILPIECE
CLIP
THUMBSCREW POP-UP ROD
CLIP
PIVOT
ROD
EXTENSION ROD
SPRING
CLIP
STOP
WASHER
90°