American Standard Undercounter Lavatory 730431-100 User manual

Adjustable Wrench
Channel Lock Pliers
Regular Screwdriver
Undercounter Lavatory
Installation Instructions Observe Local Plumbing
and Building Codes
Recommended Tools & Materials
1
Introduction: Thank you for selecting our products...products which
have been the benchmarks of fine quality for years. To help insure that
the installation process will proceed smoothly, please read these instruc-
tions carefully before you begin. Also, review the recommended tools
and materials list; carefully unpack and examine your new plumbing
fixture.
Phillips Screwdriver
10'
Pipe Wrench
Putty Kinfe
Drill
Saber Saw
Basin Wrench
Plumbers' Putty
Tubing Cutter
Tape
Measure
Hacksaw
730431-100 © American Standard Inc. 1997
If making a cutout is necessary,
locate the position of the lava-
tory. Provide proper clearance
under the countertop for the
faucet supply lines, drain
assembly and the structural
parts of the cabinet. Turn
upside down and trace perimeter
of lavatory. NOTE: If replacing an
existing lavatory be certain to
shut off water supply before
removing old lavatory.
AMERICAN STANDARD ONE-YEAR LIMITED WARRANTY
If inspection of this American Standard plumbing product, within one year
after its initial installation, confirms that it is defective in materials or workmanship,
American Standard will repair or, at its option, exchange the product for a similar
model.
This limited warranty does not apply to local building code compliance;
since local building codes vary considerably, the purchaser of this product should
check with a local building or plumbing contractor to insure local code compliance
before installation.
This warranty shall be void if the product has been moved from its initial
place of installation; if it has been subjected to faulty maintenance, abuse, misuse,
accident or other damage; if it was not installed in accordance with American
Standard's instructions; or if it has been modified in a manner inconsistent with the
product as shipped by American Standard.
American Standard's option to repair or exchange the product under this
warranty does not cover any labor or other costs of removal or installation, nor
shall American Standard be responsible for any other incidental or
consequential damages attributable to a product defect or to the repair or
exchange of a defective product, all of which are expressly excluded from
this warranty. (Some states or provinces do not allow the exclusion or limitation
of implied warranties, so this exclusion may not apply to you.)
This warranty gives you specific legal rights. You may have other statutory
rights that vary from state to state or from province to province, in which case this
warranty does not affect such statutory rights.
For service under this warranty, it is suggested that a claim be made through
the contractor or dealer from or through whom the product was purchased, or that
a service request (including a description of the product model and of the defect)
be sent to the following address:
In the United States: AMERICAN STANDARD, INC.
P.O. Box 6820
Piscataway, New Jersey 08855
Attn: Director of Consumer Affairs
For residents of the United States, warranty information may also be
obtained by calling the following toll free number: [phone]
In Canada: AMERICAN STANDARD, INC.
1401 Dupont Street
Toronto, Ontario Canada M6H 2B1
Toll Free: [phone] Toronto Area: [phone]
In Mexico: IDEAL STANDARD, S.A. de C.V
Customer Service Manager
Planta Santa Clara,Via Morelos #330
Santa Clara Coatitla
Ecatepec de Morelos 55540,
Estado de Mexico, Mexico
Saniwares
Silicone Adhesive
Product names listed herein are trademarks of American Standard Inc. unless otherwise noted.

3
4
5
2
7
8
9
10
730431-100
6
Cut opening 1-1/2" inside
the perimeter line
of the lavatory.
Perimeter
of lavatory
Cutout
1-1/2"
On underside of countertop,
locate mounting hardware
holes as shown 1-7/8"
outside of cutout.
LOCATION OF CLIPS
1-7/8" TYP.-4 PLACES
45˚
LOCATION OF MOUNTING HOLES
3/4 MIN.
Drill 1/8 dia. X 3/8 deep
#10 Wood Screw
3/4 MIN.
Clip
Drill 3/8 Dia .X 1/2 deep hole
Brass insert, epoxy
in place with threaded
end exposed. (Epoxy
not supplied).
Clip
#10-24 Mach. screw
INSTALL MOUNTING HARDWARE
FOR MARBLE OR SOLID SURFACES FOR WOOD
A
Mount the drain assembly (not included)
on the lavatory, following faucet
manufacturer's instructions. Be certain
to apply a bead of sealing putty on the
underside of the drain (Part "A") in
order to ensure a watertight seal
between the lavatory and drain. Remove
excess putty after installing drain on
lavatory.
Center bowl over cutout and tighten
screws (see 4) to secure bowl to
countertop. Remove excess sealant
from inside lip.
After checking fit and
alignment of lavatory to cut
out, apply a bead of silicone
adhesive to rim of lavatory.
BC
Shut-Off Valves
Connect supply line to faucet
(finger tight) and carefully bend
tubes to engage with the supply
shut-off valves. Tighten
connections at faucet and shut-off
valves for water tight seal.
Connect trap to drain assembly
hand tight to check alignment. It
may be necessary to cut off part
of the tailpiece (area "B") or part
of the horizontal leg of the trap
(area "C"). Secure joints for
watertight assembly.
Install faucet (not included)
and countertop (not included)
following manufacturers
instructions.