American Standard TOWNSQUARE T555.500 User manual

TOWNSQUARE
Required Tools
Adjustable Wrench Channel Locks
Flat Blade Screwdriver
Plumbers' Putty or Caulking
Phillips Screwdriver
BATH/SHOWER TRIM KIT
1-5/8" TO 3-1/4"
FINISHED WALL
BOTTOM OF
TUB
74" FOR
HEAD CLEARANCE
2" REF.
18"
OPTIONAL
1/2" I.P.S.
1
7-5/8"
OPTIONAL TO
FINISHED FLOOR
USUALLY BETWEEN
65'' AND 78''
8" REF.
4" TOP OF
TUB RIM
1-3/4" REF.
1/2" COPPER
7-1/4" REF.
Certified to comply with ANSI A112.18.1
M968235 Rev. 1.5
T555.500
T555.501
T555.502
Installation
Instructions
ROUGHING-IN DIMENSIONS
■To assure proper positioning in relation to
wall, note roughing-in dimensions.
PRESSURE BALANCING BATH
AND SHOWER TRIM KIT
Thank you for selecting American-Standard...the benchmark
of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--please
read these instructions carefully before you begin.

3
5
6
3
1
2
4
2INSTALL HANDLE
Install HANDLE BUSHING (1) onto CAP (2).
Find correct position of HANDLE (3) and push
HANDLE (3) onto VALVE STEM (4).
Install HANDLE SCREW (5) and push in INDEX
CAP (6).
Check proper operation of HANDLE.
Turn water supply on and test installed fitting.
Operate valve and diverter spout.
1
5
1
3
1
1
9
7
5
3
1
0
1
5
4
3
2
1
5
1
3
1
1
9
7
5
3
1
1
5
1
3
1
1
9
7
5
3
1
COLDER
(Larger Numbers)
0 1 3 5 7 9 11 13 15
HOTTER
(Smaller Numbers)
0 1 3 5 7 9 11 13 15
1
5
4
3
2
1INSTALL TRIM
CAUTION: Protect finish on SHOWER ARM,
SHOWER HEAD and TUB SPOUT when installing.
2
A
6
7
3
1
4
5
5
8
■By restricting HANDLE rotation and limiting the
amount of hot water allowed to mix with the
cold, the HOT LIMIT SAFETY STOP (1) reduces
risk of accidental scalding. To set the maximum
hot water temperature of your faucet, you
need to adjust the setting on the HOT LIMIT
SAFETY STOP (1).
■Turn CARTRIDGE STEM (2) to the OFF position
(coldest setting) before making adjustment to
HOT LIMIT STOP (1). Use a flat blade
screwdriver to pry free the HOT LIMIT SAFETY
STOP (1).
Pull forward and rotate counterclockwise
one number to limit hot water temperature.
Use ARROW (3) on CARTRIDGE (4) and
NUMBERS (5) on HOT LIMIT STOP (1) for
indication. M968235 Rev. 1.5
ADJUST HOT LIMIT STOP
HEX WRENCH
When finished tiling the wall, remove PLASTER GUARD (A)
and turn off water supply.
Push CAP (1) over VALVE CARTRIDGE (2).
Mount ESCUTCHEON (3) to valve body with SCREWS (4).
Remove PIPE CAPS (5) from shower pipe and tub filler pipe.
Install SHOWER ARM (6), SHOWER HEAD (7) by threading
onto pipe nipples using teflon tape or pipe sealant.
Install SLIP-ON TUB SPOUT (8). Tighten with
HEX WRENCH supplied.
1-3/4" REF.

4
M968235 Rev. 1.5
ROTATE 180˚
12
9
5
5
7
86
43
INLETS
LARGE OUTLET
BACK TO BACK INSTALLATION
5
Pull INDEX CAP, unscrew HANDLE SCREW and pull HANDLE off valve stem.
Remove two SCREWS holding ESCUTCHEON and remove ESCUTCHEON.
Remove COVER by pulling straight out.
Shut off water supply by either closing off main water supply, or closing off the hot and cold CHECK STOPS on valve.
BACK TO BACK INSTALLATION
Remove PRESSURE BALANCE UNIT (5). Rotate PRESSURE BALANCE UNIT (5) 180˚ so that the inlets face up and the
large outlet port faces down.
Push PRESSURE BALANCE UNIT (5) in casting make sure inlets line up with holes in bottom of casting. Top flange should
butt up against top of casting. Reassemble FIXATION RING (4) and CARTRIDGE (1).
Remove PRESSURE BALANCE UNIT (5).
Remove CAPS (7) and clean valve thoroughly.
Examine balancing unit and check condition of O-ring on end of piston. Piston should move back and forth. Order Repair
Part M952100-0070A if balancing unit is defective.
Replace CAPS (7) and install PRESSURE BALANCE UNIT (5). Make sure inlets line up with two holes in bottom of casting.
Top flange should butt-up against top of casting.
UNABLE TO MAINTAIN CONSTANT TEMPERATURE
Remove CARTRIDGE (1) by removing CARTRIDGE SCREWS (2). Remove three SCREWS (3) from FIXATION RING (4) and
pull out PRESSURE BALANCING (5) unit.
Clean SEALS (9) on base of CARTRIDGE (1). Check base of PRESSURE BALANCING UNIT (5) and clean O-RINGS (6). Remove
CAPS (7) and check O-RINGS on inside of CAPS (7) for debris. Clean inside sealing surfaces of VALVE BODY (8).
Re-assemble PRESSURE BALANCING UNIT (5) and CARTRIDGE (1). Tighten all screws.
Turn on water supply and see above for installing TRIM and HANDLE. If it still leaks, replace pressure balancing unit
(M952100-0070A).
VALVE LEAKS WHEN SHUT OFF
TO GAIN ACCESS TO VALVE FOR SERVICING
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS: