Ameriwood HOME 4693337COM User manual

2 Door Pantry
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Assembly Difficulty Meter
Easy Tough
WARNING: Manufacturer assumes no liability
for improper installation or excessive loads
placed on screws or bracket. This wall anchor
is not a substitute for proper adult supervision.
Keep your home and family safe
with the wall anchor kit that is
included with the product.
Serious or fatal crushing injuries can
occur from tipping furniture.
Secure Your Furniture

Helpful Hints
2
- Open your item in the area you plan to keep it to avoid excessive heavy lifting.
- Identify, sort and count the parts before attempting assembly.
- Compression dowels are lightly tapped in with a hammer.
- Slides are labeled with a
R (right) and L (left) for proper placement.
- Make sure to always face the point on the top of the Cam Lock towards the
outer edge.
- Use all the nails provided for the back panel and spread them out equally.
- Back panel must be used to make sure your unit is sturdy.
- Do NOT use harsh chemicals or abrasive cleaners on this item.
- Never push, pull, or drag your furniture.
PEOPLE NEEDED FOR ASSEMBLY: 1-2

3
Before You Start
P
Quick
Tip
Assembly
P
P
P
Cam Lock Fastening System
This Cam Lock Fastening System will be used throughout the assembly process.
1
3
2
4
P
Press parts together so CAM BOLT inserts
into edge hole.
Press CAM BOLT into hole. Press CAM LOCK into hole.
Using a screwdriver, turn the CAM LOCK clockwise to
lock the CAM LOCK and CAM BOLT into their holes
and fastening parts together.
Arrow to point towards end
hole in edge of part.
End hole
Read through each step carefully and follow the proper order
Separate and count all your parts and hardware
Parts are labeled on the surface or edge of the part
Give yourself enough room for the assembly process
Have the following tools: Flat Head Screwdriver, #2 Phillips Head
Screwdriver and Hammer
Caution: If using a power drill or power screwdriver for screwing,
please be aware to slow down and stop when screw is tight.
Failure to do so may result in stripping the screw.

4
Before You Start
Quick
Tip
Assembly
Please Note:
You may need to lightly tap the wood dowels into the holes during
your assembly process.
wood dowel

5
Board Identification
Not actual size
Left Panel
34693337010 Right Panel
34693337020
Top
34693337030
Bottom
34693337040
Shelf
34693337050
Upper Adjustable Shelf (2)
34693337060
Door (2)
34693337080
Upper Back Panel
K469333700 Lower Back Panel
K469333710
These pieces are paperboard construction.
They are not made from wood, but are
required for the assembly of your unit.
AB
C
F
D
G
E
H
I
J
Lower Adjustable Shelf (2)
34693337070

6
Board Identification
Not actual size
A
B
C
D
E
F
G
H
I
J
These pieces are paperboard
construction.
They are not made from wood,
but are required for the
assembly of your unit.
F
G
H

7
Part List
Actual Size
Not Actual Size
(x8)
#A22700
cam lock
(x8)
#A22710
cam bolt
(x6)
#A21670
wood dowel
(x4)
#A23030
confirmat
(x16)
#A80250
shelf support
(x54)
#A21110
nail
(x4)
#A17400
7/8" bolt
(x2)
#A50415
handle
(x4)
#A65615
hinge
(x4)
#A43105
foot
(x1)
#A84050
safety bracket kit
12
345
8
6
11
10
9
9a
9b
9c
9d
(x4)
#A89210
rubber pad
7
12

8
STEP1
3
2
2
3
1
(x2) (x2) (x1)
1
Proper orientation of CAM LOCK
Tip
Assembly
Quick
1
2
A

9
STEP2
12
3
1
3
2
(x2) (x2) (x1)
2
1
Proper orientation of CAM LOCK
Tip
Assembly
Quick
B

10
STEP3
13
1
3
1
(x4) (x4)
1
1
3
3
3
E
Proper orientation of CAM LOCK
Tip
Assembly
Quick

11
STEP4
A
E
B
UNLOCKLOCK
Finished edges up

12
STEP5
4
4
44
4
D
A
B
(x4)
Finished edges up

13
STEP6
10
10
10
10
10
D
Note: You may need to tap feet with a hammer to fully seat.
(x4)

14
STEP7
2
2
(x4)
2
2
2
C

15
STEP8
UNLOCKLOCK
C
A
B

16
STEP9
Flush the bottom edge of the Lower Back Panel
with the bottom edge of Bottom (D).
Assure that the unit is square.
Distance from corner to corner
must be equal as shown.
8
8
J
I
D
B
(x54)
IMPORTANT! THE BACK PANELS ARE A STRUCTURAL PART OF THIS UNIT
AND MUST BE INSTALLED PROPERLY.
Carefully turn the cabinet over on it's front side.
Position upper back panel as shown. Align squarely with outer edges.
Flush bottom edge of upper back panel with bottom edge of fixed shelf
(E) and nail straight into back edges of left panel, right panel and top.
Position lower back panel as shown. Align squarely with outer edges.
Flush bottom edge of lower back panel with bottom edge of bottom (D)
and nail straight into back edges of left panel, right panel, bottom and
fixed shelf.
raw
surface
raw
surface

17
STEP10
For Masonry, Concrete, or other
wall materials:
Consult your local hardware store
for appropriate anchors to securely
attach the safety bracket.
IMPORTANT: THIS UNIT MUST BE SECURE TO THE WALL TO HELP PREVENT TIPOVER. FOLLOW
THESE INSTRUCTIONS TO INSTALL THE ANTI-TIPPING SAFETY BRACKET PROVIDED WITH THIS
PRODUCT.
WARNING
Serious or fatal crushing injuries can
occur from furniture tipover.
To prevent tipover:
* Install tipover restraint provided
* place heaviest items in the lowest
drawers
* Unless specifically designed to
accommodate, do not set TVs or
other heavy objects on the top of this
product
* Never allow children to climb or
hang on drawers, door, or shelves
* Never open more than one drawer
at a time
Use of tipover restraints may only
reduce, but not eliminate the risk of
tipover
OPTION 1: Attachment into a wall stud (preferred method)
Using a stud finder, locate a stud in the wall. Place your unit against the wall, with the safety bracket
aligned in this location. To make driving the screw easier, you can drill a 1/8" diameter pilot hole (3mm)
through the safety bracket into the stud. Drive the screw through the safety bracket into the wall stud.
OPTION 2: Attachment into drywall
Locate your unit where desired against a wall and mark the wall through the safety bracket, then move
your unit aside. Drill a 3/16" diameter hole (5mm) into the wallboard. Tap the wall anchor into the hole
until it is flush. Move your unit into location and fasten the wall bracket to the wall anchor with the
screw.
stud
wallboard
hole
9b
9a 9c
9d
9b
9a
9c
9d
C

18
STEP11
5
5
F
F
G
G
5
5
5
5
5
5
5
5
(x16)
finished edge
finished edge
Note:
The top two adjustable shelves (F) have finished surface on both sides.

19
STEP12
11
67
12
7
6
(x4)
(x4) (x4)
(x2)
12
12
7
6
H
x2
11

20
STEP13
H
H
Note:
This view shows attaching the doors for "left handle" doors.
If you prefer "right handle" doors, attach the door hinges to
the right panel.