Amico RS-42-PKS Series Original operating instructions

1
Roll Stand
Quick Installation and Maintenance Instructions
RS_-42_-PKG/RS_-LCD-PKG
Installing Casters & Post into Base
!
WARNING: Do not use a hammer on the CASTERS or ROLL STAND base when installing CASTERS. Doing so will damage the CASTERS.
1. Push each of the 5x CASTERS into a leg by hand until it clicks in place, as shown in Figure 1.
2. Insert the POST into the BASE ADAPTER. Using a 1/2" socket wrench, secure by inserting the SCREW through the LARGER WASHER,
SMALLER WASHER, the STAND BASE underside, and BASE ADAPTER into the POST, as seen in Figure 2.
Locking & Unlocking Casters
1. To lock the CASTERS, step on the LOCKING LEVER such that it clicks in the down position.
2. To unlock the CASTERS, lift the LOCKING LEVER up as seen in Figure 3.
Medical Facility Responsibility
Preventive maintenance checks must be performed regularly to maintain the quality and
performance of this product. Any parts that may be broken, missing, worn, distorted or
contaminated in any way should not be used and all affected parts should be replaced
immediately. Should the necessity of any repair be suspected; please contact your local Amico
distributor.
!
WARNING: It is the responsibility of the end user to ensure all aspects of the installation
are covered by following the full manual found at:
https://www.amico.com/sites/default/files/product/downloads/amico-aa-rst-
roll-stand-manual.pdf
Installation Tools
WARNING: If the product was purchased with counterweight, perform Installing Counterweight step 1 and/or step 2 from the full
manual. If not, proceed to the Installing Casters & Post into Base section.
3/16" Hex Key 1/2" (12.7 mm) Socket Wrench
#2, #3 Phillips Head Screwdrivers
PATIENT MONITOR
SHELF TILT ADJUSTMENT
HANDLE
CORD WRAP
3" (7.6 cm) LOCKING CASTERS
BASKET
ALUMINUM CONSTRUCTION
STAND POST
[X-RS-POST]
BASE ADAPTER
[RS-ADA-125]
STAND BASE
[X-RS-BASE]
POST HW-KIT SMALL WASHER
[H-STW-516-SMOD]
POST HW-KIT LOCK WASHER
[H-RS-LOCK-WASH]
POST HW-KIT LARGE BOLT
[H-HSCS-51618-312]
FIGURE 1
CASTERS
[X-RS-CSTR-3B]
5X
STAND BASE
[X-RS-BASE]
PROJECT #: 0378
FOR USE WITH: RS(5/6/7)-((42(0/2/3/4/6/7/8/9/W))/LCD)(-PKG)
WARNING: DO NOT USE A HAMMER ON THE CASTERS OR ROLL STAND BASE WHEN INSTALLING CASTERS. DOING SO WILL DAMAGE THE CASTERS
PUSH 5X
CASTERS INTO STAND BASE BY HAND UNTIL IT CLICKS IN PLACE, AS SHOWN IN FIGURE 1. 1.
INSERT STAND POST INTO BASE ADAPTER . USING 1/2" SOCKET WRENCH, SECURE BY INSERTING POST HW-KIT-LARGE BOLT THROUGH POST 2.
HW-KIT LOCK WASHER , POST HW-KIT SMALL WASHER , STAND BASE , BASE ADAPTER , AND INTO STAND POST , AS SEEN IN FIGURE 2.
CUSTOMER
FIGURE 2
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
2
6
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
Assembly instructions for Roll Stand
EC
2014-02-28
JT
2014-08-04
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
RS_-___-___
20140228-E2799
PROJECTION
STAND BASE
[X-RS-BASE]
5x CASTERS
[X-RS-CSTR-3B]
STAND POST
[X-RS-POST]
BASE ADAPTER
[RS-ADA-125]
STAND BASE
[X-RS-BASE]
POST HW-KIT SMALL WASHER
[H-STW-516-SMOD]
POST HW-KIT LOCK WASHER
[H-RS-LOCK-WASH]
POST HW-KIT LARGE BOLT
[H-HSCS-51618-312]
FIGURE 1
CASTERS
[X-RS-CSTR-3B]
5X
STAND BASE
[X-RS-BASE]
PROJECT #: 0378
FOR USE WITH: RS(5/6/7)-((42(0/2/3/4/6/7/8/9/W))/LCD)(-PKG)
WARNING: DO NOT USE A HAMMER ON THE CASTERS OR ROLL STAND BASE WHEN INSTALLING CASTERS. DOING SO WILL DAMAGE THE CASTERS
PUSH 5X
CASTERS INTO STAND BASE BY HAND UNTIL IT CLICKS IN PLACE, AS SHOWN IN FIGURE 1. 1.
INSERT STAND POST INTO BASE ADAPTER . USING 1/2" SOCKET WRENCH, SECURE BY INSERTING POST HW-KIT-LARGE BOLT THROUGH POST 2.
HW-KIT LOCK WASHER , POST HW-KIT SMALL WASHER , STAND BASE , BASE ADAPTER , AND INTO STAND POST , AS SEEN IN FIGURE 2.
CUSTOMER
FIGURE 2
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
2
6
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
Assembly instructions for Roll Stand
EC
2014-02-28
JT
2014-08-04
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
RS_-___-___
20140228-E2799
PROJECTION
STAND POST
[X-RS-POST]
BASE ADAPTER
[RS-ADA-125]
POST HW-KIT SMALL WASHER
[H-STW-516-SMOD]
POST HW-KIT LARGE BOLT
[H-HSCS-51618-312]
POST HW-KIT LOCK WASHER
[H-RS-LOCK-WASH]
STAND BASE
[X-RS-BASE]
Figure 1 Figure 2
LOCK
UNLOCK
LOCKING
LEVER
PROJECT #: 0378
FOR USE WITH: RS(5/6/7)-((42(0/2/3/4/6/7/8/9/W))/LCD)(-PKG)
TO LOCK THE
CASTERS , STEP ON THE LOCKING LEVER SUCH THAT IT CLICKS IN THE DOWN POSITION. 1.
TO UNLOCK THE CASTERS , LIFT THE LOCKING LEVER UP 2.
CUSTOMER
FIGURE 1
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
66
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
Assembly instructions for Roll Stand
EC
2014-02-28
JT
2014-08-04
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
RS_-___-___
20140228-E2799
PROJECTION
LOCK
UNLOCK
LOCKING
LEVER
Figure 3

Amico Accessories Inc. | 85 Fulton Way, Richmond Hill, ON L4B 2N4, Canada | www.amico.com
Toll Free Tel: [phone] | Tel: [phone] | Fax: [phone] | Email: [e-mail]
Roll Stand
Quick Installation and Maintenance Instructions
RS_-42_-PKG/RS_-LCD-PKG
2
Troubleshooting Guide
Maintenance
It is recommended that once every three (3) months, all locks, bolts and screws are visually inspected for signs of product wear and tear or damage.
Symptom Possible Cause Solution
Roll Stand is difficult to maneuver Locked or unsecured caster Refer to instructions (Adjustments)
Device is loose on Roll Stand head Device secured improperly/lock plunger not engaged Refer to instructions (Device Installation)
Locking & Unlocking Casters
1. Using a 1/2" socket wrench, insert the SCREW through the BRONZE
WASHER, the NYLON WASHER, the MONITOR HEAD, the black PLASTIC
BUSHING, and the BASE ADAPTER into the POST as seen in Figure 4.
2. Cover the HEAD of the SCREW with the Amico doming label by placing
the adhesive side down onto the MONITOR HEAD over the SCREW.
Warranty
Amico Accessories Inc. warrants all mounting accessories to be free from defects in material and workmanship for a period of twelve (12)
months from the date of shipment. Within this period Amico Accessories Inc. will repair or replace any part which is proven to be defective.
Amico Accessories Inc. will warrant its materials to be free from defect for an additional period of four (4) years, (five [5] years from the date
of shipment). Within this period, Amico Accessories Inc. will replace any part which is proven to be defective, at no charge. Shipping and
Installation costs after the first twelve (12) months will be borne by the Customer.
This warranty is valid only when the product has been properly installed according to Amico Accessories Inc. specifications, used in a normal
manner and serviced according to factory recommendations. It does not cover products that are not manufactured by Amico Accessories
Inc. It does not cover failures due to damage which occurs in shipments or failures which result from accidents, misuse, abuse, neglect,
mishandling, alteration, misapplication or damage that may be attributable to acts of God.
Amico Accessories Inc. shall not be liable for incidental or consequential damages resulting from use of equipment.
All claims for warranty must first be approved by Amico Accessories Inc. A valid Return Goods Authorization (RGA) number must be obtained
from Amico Accessories Inc. prior to commencement of any service work. Warranty work, which has not been pre-authorized by Amico
Accessories Inc., will not be reimbursed.
AMICO ACCESSORIES INC. DOES NOT HONOR VERBAL STATEMENTS CONCERNING THE WARRANTY.
The distributor and/or dealer are not sanctioned to create verbal warranties about the product described in this agreement. Any statements
will not be honored or be made part of the agreement of sale. This document is the final complete and exclusive terms of the agreement.
THIS WARRANTY IS INCLUSIVE AND REPLACES ALL OTHER WARRANTIES.
Amico Accessories Inc. shall not, under any circumstances be liable for incidental or consequential damages including, but not limited to,
profit, loss of sales or injuries to person(s) or property. Correction of noncompliance as noted above will result in completion of all liabilities of
Amico Accessories Inc., whether based on agreement, neglect or changed materials, designs or specifications without notice.
All claims for warranty must first be approved by Amico Accessories Inc. Service Department: [email protected] or 1.877.264.2697. A
valid Return Goods Authorization number must be obtained from Amico Accessories Inc. prior to commencement of any warranty claim.
AAQGRSTROLLSTAND 04.18.2018
AMICO STICKER
[X-DOME-CIR-LBL]
HEAD HW-KIT
BRONZE WASHER
[H-BZWASH-516-34]
MONITOR HEAD
[X-MONHEAD-_]
POST ADAPTER
[RS-ADA-125]
STAND POST
[X-RS-POST]
PLASTIC BUSHING
[X-MON-BUSH-SM]
HEAD HW-KIT
NYLON WASHER
[H-NYL-WSH-516]
HEAD HW-KIT
LARGE BOLT
[H-SCS-51618-35]
HEAD HW-KIT NYLON WASHER
[H-NYL-WSH-516]
HEAD HW-KIT BRONZE WASHER
[H-BZWASH-516-34]
HEAD HW-KIT LARGE BOLT
[H-SCS-51618-35]
MONITOR HEAD
[X-MONHEAD-_]
PLASTIC BUSHING
[X-MON-BUSH-SM]
POST ADAPTER
[RS-ADA-125]
STAND POST
[X-RS-POST]
FIGURE 1
CAUTION STICKER
[X-LBL-MAX-15]
PROJECT #: 0378
FOR USE WITH: RS(5/6/7)-((42(0/2/3/4/6/7/8/9/W))/LCD)(-PKG)
USING 1/2" SOCKET WRENCH, INSERT
HEAD HW-KIT LARGE BOLT THROUGH HEAD HW-KIT-BRONZE WASHER , HEAD HW-KIT NYLON 1.
WASHER , MONITOR HEAD , PLASTIC BUSHING , POST ADAPTER , AND INTO STAND POST AS SHOWN IN FIGURE 1.
COVER THE HEAD OF HEAD HW-KIT LARGE BOLT WITH CAUTION STICKER BY PLACING THE ADHESIVE SIDE DOWN ONTO THE MONITOR 2.
HEAD
CUSTOMER
5
4
3
2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
3
6
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
Assembly instructions for Roll Stand
EC
2014-02-28
JT
2014-08-04
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: [phone]
Fax: [phone]
RS_-___-___
20140228-E2799
PROJECTION
Figure 4