Amiko Smart Home Installation and operation manual

Smart Home
User Manuals
www.amikohome.com

Picture is illustration

Smart Home - Door Sensor
- User Manual
www.amikohome.com
1.1
Introduction
Thank you for choosing AMIKO HOME smart door
sensor. AMIKO Smart Door Sensor uses ZigBee
technology with low power consumption, low data
rate and low complex wireless rate. The wireless
network technology provides reliability and stability,
with the magnetic sensor following the status of any
door or window where the sensor is used. With
double sensor design the installation is very easy and
flexible. The sensor gives accurate data when the
door status changes with real-time detection. Main
unit and the magnetic contact can be installed on
each door side. When the door or window is opened,
the sensor sends message to ZigBee network.
Suitable for any network in ZigBee HA protocol.
Caution
1. The product communicates wireless, please
don’t put the product in the metal box to
prevent the signal from shielding;
2. The temperature environment range is
between 10℃and +55℃; Humidity ≤ 95%RH.
3. Avoid using in the chemistry, combustible
gas, saturated salt fog or other abnormal
environment;
4. It should be installed in a place with no snow
and rain. The medium should be without gas or
dust that can corrode metal, destroy the
insulation and/or explode.
Installation
1. Tear down adhesive film, stick it to chosen
area. (Detector should be put on a fixed place,
magnet part can be on the moving part.)
2. Install the 2 parts in alignment, distance
must be less than 15 mm from each other.
(Magnet can either be installed on the left or
right side of the sensor.) (1.1)
Performances
Power supply
Standby Power
Working Frequency
Receiving Sensitivity
Communication Distance
Network Distance
Protocol
Working Temperature Range
Detection Range
Detection Size
Magnet Size
Specification
DC 3V (2xAAA)
15uW
2405-2480MHz
-97dBm
100m
50m
ZigBee HA
-10℃~+55℃
>15mm
76*36.6*16.5mm
76*13.9*16.5mm
Operation
1. The product configures with AMIKO smart
gateway HUB;
2. Put the battery (2 x AAA) into the door
sensor, put back the plastic cover and switch the
reset button through the whole. As soon as the
light on the device starts blinking press OK
button on HUB to join the network.
3. Within 1 minute your
door sensor will appear
in Device Manager of
AMIKO HOME mobile
application. You can see
and/or rename your
device in the app.
Note: If failed, repeat the
above procedure. If failed
after many attempts, please
set back to factory mode.
4. Your door sensor is
now ready to send alerts
to the application when
opened/closed.
5. Set back to factory mode: Long press smart
door sensor network button for about 8
seconds, the indicator light flashes 2 to 3 sec,
then blinks. Then the smart door sensor returns
to factory settings.
Specifications

Smart Home - HUB
- User Manual
www.amikohome.com
Introduction
Thank you for choosing AMIKO HOME Smart
Home HUB. Smart HUB is easy to install. The
easy-operating control interface makes the
setting way easier. Following the latest HA
protocol,the gateway can work with Zigbee LL
and HA protocol products.
Structure
The front side of the
product is shown on
picture 2.1
The back side of the
product is shown on
picture 2.2
Caution
1. Please make sure you are using the power
adapter that we provide before installation,
other adapter may cause safety issue.
2. The product communicates wireless, please
don’t put the antenna in a metal box to prevent
the signal from shielding.
3. The operational environment temperature
range is between - 35 ºC and +70 ºC.
4. Avoid using the equipment in chemicals,
flammable gas, saturated acid fog or other
abnormal environment.
5. Should be installed in the place of non-shaking,
non-oscillating, non-wind and non-rain hitting.
Operation
1. Power on the gateway
with power adapter, and
connect the gateway to
the router with Ethernet
cable. See picture 5.1.
2. When the gateway is powered the led turns
red or orange. Then push the OK button to
allow the device joining the network, the led
flashes red, blue and finally green when the
internet connection is set. See picture 5.2.
2.1
OK button
ETHERNET port
DC5V power
RESET
button
2.2
5.1
3. Scan app QR code to download the app.
(See picture 5.3)
4. In AMIKO HOME mobile app’s Device
Manager read the QR code of your equipment
(HUB) and click SAVE. You can see and/or
rename your device in the Device Manager.
5. For factory reset your gateway, please press
the RESET button for longer period (more than
5 sec), the led will flash red, blue and green.
5.2
Google Play and the Google Play logo are trademarks of Google Inc.
5.3
Specifications
Performances
Voltage
Operating Frequency Band
Accessible Communication Range
Accessible Network Range
Transmitted Power
Receiver Sensitivity
Working Temperature
Dimension
Specification
DC5V\200mA
2405~2480MHz
600m
300m
20dBm
-92dBm
-35℃ 〜+70℃
108*108*25mm

Smart Home - Motion Sensor
- User Manual
www.amikohome.com
Introduction
Thank you for choosing AMIKO HOME Smart Motion
Sensor. AMIKO Smart Motion Sensor is developed to
work with ZigBee protocol that enables the PIR
(infrared) sensor to send alert to AMIKO HOME mobile
application, when noticing movement in the covered
area. The Smart Motion Sensor connects to the smart
home network via AMIKO Smart HUB. Users can get
the motion alerts to their mobile devices via the
mobile application.
Our Smart Motion Sensor can either be connected to
indoor light for energy saving (automatic power
ON/OFF) or to an alarm system for anti-theft solution.
The product uses the ZigBee technology, with low
power consumption and low data rate. At the same
time it provides a very stable and reliable solution for
sensing approach and rea -time detection of the body.
Caution
1. The product communicates wireless, please
don’t put the product in the metal box to
prevent the signal from shielding;
2. The temperature environment range is
between −25℃and +85℃;
3. Avoid using in the chemistry, combustible
gas, saturated salt fog or other abnormal
environment;
4. It should be installed in a place with no snow
and rain. The medium should be without gas or
dust that can corrode metal, destroy the
insulation and/or explode
.
Installation
1. Tear down
adhesive film, attach
the PIR motion
sensor to required
area.
2. Hang motion
sensor on the
pedestal. Please
beware of the
installation direction.
Operation
1. Device must be paired with AMIKO Smart
HUB;
2. Put the battery (CR 123A) into the motion
sensor, put back the plastic cover and long
press the reset button. As soon as the light on
the device starts blinking press OK button on
HUB to join the network.
3. Within 1 minute your motion sensor will
appear in Device Manager of AMIKO HOME
mobile application. You can see and/or rename
your device in the app.
Note: If failed, repeat the above procedure. If failed
after many attempts, please set back to factory mode.
4. Your motion sensor is now ready to send
alerts to the application when detecting
movement.
5. Set back to factory mode: long press smart
motion sensor network button for about 8
seconds, the indicator light flashes 2 to 3 sec,
then blinks. Then the smart motion sensor
returns to factory settings .
Specifications
(1)
(2)
Performances
Power supply
Standby Power
Working Frequency
Receiving Sensitivity
Communication Distance
Network Distance
Protocol
Working Temperature Range
Detection Range
Installation height
Dimension
Specification
DC 3V (CR123A button battery)
48µW
2405-2480MHz
-97dBm
100m
50m
ZigBee HA
-10℃~+50℃
9-12m
2.1m
65mm*65mm*28mm

Smart Home - Smart Plug
- User Manual
www.amikohome.com
Introduction
Thank you for choosing AMIKO HOME Smart
(out of the wall) plug.
AMIKO Smart Plug is developed to work with
ZigBee protocol that enables this plug to
connect to the smart home network via AMIKO
Smart HUB. Users can use their mobile devices
as a remote controller via the mobile
application.
Our smart plug can be connected to any EU
standard wall socket, and the device plugged
into this socket can remotely be switched
ON/OFF via AMIKO HOME mobile application.
There is a physical button on the smart plug for
easy ON/OFF switch. ZigBee data transmission,
with built in grounding.
Caution
1. It is a wireless communication product.
Please don’t put it in metal box while working to
avoid signal being shielded.
2. Operating ambient temperature should be
-25°C to 85°C
3. Avoid using the equipment in chemicals,
flammable gas, saturated acid fog or other
abnormal environment
4. It should be installed in a place with no snow
and rain. The medium should be without gas or
dust that can corrode metal, destroy the
insulation and/or explode.
Installation
1. Device must be paired
with AMIKO Smart HUB.
2. Plug in the smart plug
into a wall socket. Blue
light means OFF status,
orange light means ON
(under electricity) status.
Press POWER button on smart plug for 5 sec,
wait until it starts blinking blue-orange color.
When it is blinking the smart plug is ready for
pairing.
3. Press OK button on the gateway, then it
starts looking for a new device. When the
pairing is done, AMIKO Smart Plug will
automatically appear in AMIKO HOME
application Device Manager as a new device.
Note: If failed, repeat the above procedure. If
failed after many attempts, please set back to
factory mode.
4. rename, assign to a room and manage your
smart plug in Device Manager.
5. Restore the factory settings: long press the
power button for 5 seconds, when networking
lights start flashing then the smart plug has exited
the ZigBee network and ready for pairing again.
Specifications
Performances
Power Supply:
Load Capacity:
Standby Power:
Frequency:
Wireless Output Power:
Receiving Sensibility:
Accessible Communication
Distance:
Accessible Networking
Distance:
Protocol:
Working Temperature Range:
Dimension:
Specification
220V (EU)
2000W
<0.6W
2405-2480MHz
20dBm
-101dBm
300m（+PA）
150m（+PA）
ZigBee HA
-25℃~+70℃
110mm*62mm*53mm

Smart Home - Smart RGBW LED Bulb
- User Manual
www.amikohome.com
Introduction
Thank you for choosing AMIKO HOME Smart
RGBW Led Bulb.
In April, 2012 Zigbee Alliance announced the
standard and authentication of Zigbee Light
Link, which was completed and officially put
into use. This makes worldwide lighting
solutions flexible and efficient with wireless
control. Zigbee Light Link is a new intelligent
standard lighting protocol for ordinary
customers, products with ZigBee LL protocol
are simple to install and easy to use. It also
provides accurate and easy wireless control for
lighting.
Our product strictly follows ZLL standard and
creatively integrates it into Zigbee HA network
to ensure our smart lighting control module
conveniently enters HA network.
AMIKO Smart Bulb is developed to work with
ZigBee protocol that enables to check status
and control remotely your lights via AMIKO
HOME mobile application. The Smart Bulb
connects to the smart home network via AMIKO
Smart HUB. Users can control their lights with
their mobile devices via the mobile application.
Caution
1. The product communicates wireless, please
don’t put the product in the metal box to
prevent the signal from shielding;
2. The temperature environment range is
between −25℃and +85℃; Humidity ≤ 95%RH.
3. Avoid using in the chemistry, combustible
gas, saturated salt fog or other abnormal
environment;
4. It should be installed in a place with no snow
and rain. The medium should be without gas or
dust that can corrode metal, destroy the
insulation and/or explode.
Performances
Power supply
Standby Power
Working Frequency
Receiving Sensitivity
Communication Distance
Network Distance
Protocol
Working Temperature Range
Detection Range
Detection Size
Magnet Size
Specification
85-265VAC
15uW
2405-2480MHz
-97dBm
100m
50m
ZigBee HA
-10℃~+55℃
>15mm
76*36.6*16.5mm
76*13.9*16.5mm
Operation
1. Device must be paired with AMIKO Smart
HUB.;
2. Place the bulb into the socket and turn it to a
direction and back 5 times quickly after each
other OR switch it ON/OFF quickly after each
other 5 times. As soon as the bulb starts
blinking press OK button on HUB to join the
network.
3. Within 1 minute your smart bulb will appear
in Device Manager of AMIKO HOME mobile
application. You can see, rename, assign to a
room or manage the smart bulb in the app.
Note: If failed, repeat the above procedure. If
failed after many attempts, please set back to
factory mode.
4. Your smart bulb is now ready to be controlled
remotely via the mobile application. You can
change colour, brightness or saturation of your
light remotely with your mobile device.
5. Set back to factory mode: power on and off
five times in a row while it is powered on with
network. Then bulb light will flash three times
and the device will be reopened. That way your
device is now back to factory setting mode and
disconnected from Zigbee network.
Specifications

DC 3V (CR 2450)
Smart Home - Smart Switch
- User Manual
www.amikohome.com
Introduction
Thank you for purchasing AMIKO HOME Smart
Switch.
Compared to traditional wall switches, our
Smart Switch provides remote access to your
electronic devices. You don't need to control
the switch manually. You can switch ON/OFF
your electronic devices, lights connected to
Smart Switch via AMIKO HOME mobile
application.
Combining our Smart Switch with any other
ZigBee HA protocol devices, allows you to get
rid of indoor electrical cabling and have full
control over your electronic devices remotely.
Caution
1. The product communicates wireless, please
don’t put the product in the metal box to
prevent the signal from shielding;
2. The temperature environment range is
between −25℃and +85℃;
3. Avoid using in the chemistry,combustible
gas,saturated salt fog or other abnormal
environment;
4. It should be installed in a place with no snow
and rain. The medium should be without gas or
dust that can corrode metal, destroy the
insulation and/or explode.
Installation
Operation
1. Device must be paired with AMIKO Smart
HUB. Our smart switch is available in 1, 2 or 3
way versions, controlling 1, 2 or 3 electronic
devices via only 1 Smart Switch.
2. Take off the glass cover from the switch,
connect phase and 0 to the switch.
3. Long press the reset button under the glass
cover (small black button) until the pairing is
done. When it is done your Smart Switch will
appear in Device Manager of AMIKO HOME
application.
Note: If failed, repeat the above procedure. If
failed after many attempts, please set back to
factory mode.
4. Now you can rename, assign to a room and
manage your Smart Switch in Device Manager.
From now on you can easily swith ON/OFF your
devices (1, 2 or 3) connected to your Smart
Switch.
5. Set back to factory mode: long press smart
switch reset button for about 5 seconds, the
indicator light flashes 2 to 3 sec, then blinks.
Release it, then the smart motion switch returns
to factory settings.
Specifications
Performances
Power Voltage
Standby Power
Load Power
Working Frequency:
Wireless output power
Protocol
Communication distance
Accessible Network Range
Receiving sensitivity
Operating Temperature
Dimension
Specification
AC 110V-220V
<1W
300W
2405-2480MHz
20dBm
ZigBee HA
300m
150m
-101dBm
-25℃~+70℃
86mm*86mm*36mm

Smart Home - Temperature and Humidity Sensor
- User Manual
www.amikohome.com
Introduction
Thank you for choosing AMIKO HOME Smart
Temperature and Humidity Sensor.
AMIKO Smart Temperature and Humidity Sensor is
developed to work with ZigBee protocol that enables
the sensor to send data to AMIKO HOME mobile
application when the environment temperature and
humidity level (%) is measured. The Smart Temperature
and Humidity Sensor connects to the smart home
network via AMIKO Smart HUB. Users can get the
measured data to their mobile devices via the mobile
application. The product uses ZigBee technology, with
low power consumption and low data rate. At the
same time it provides a very stable and reliable solution
for measuring real-time environment data.
Caution
1. The product communicates wireless, please
don’t put the product in the metal box to
prevent the signal from shielding;
2. The temperature environment range is
between −25℃and +85℃;
3. Avoid using in the chemistry, combustible
gas, saturated salt fog or other abnormal
environment;
4. It should be installed in a place with no snow
and rain. The medium should be without gas or
dust that can corrode metal, destroy the
insulation and/or explode
.
Installation
1. Tear down
adhesive film, attach
the sensor to the
required area.
2. Hang temperature
& humidity sensor on
the pedestal. Please
beware of the
installation direction.
Operation
1. Device must be paired with AMIKO Smart
HUB.;
2. Put the battery (CR 2450) into the temperature
and humidity sensor, put back the plastic cover
and long press the reset button. As soon as the
light on the device starts blinking press OK
button on HUB to join the network.
3. Within 1 minute your temperature and
humidity sensor will appear in Device Manager of
AMIKO HOME mobile application. You can see,
rename, assign to a room and /or manage your
device in the app.
Note: If failed, repeat the above procedure. If
failed after many attempts, please set back to
factory mode.
4. Your temperature and humidity sensor is now
ready to send data (temperature and humidity
level) about the environment to the application.
5. Set back to factory mode: long press smart
temperature and humidity sensor network
button for about 8 seconds, the indicator light
flashes 2 to 3 sec, then blinks. Then the smart
temperature and humidity sensor returns to
factory settings.
Specifications
(1)
(2)
Performances
Power supply
Standby Power
Working Frequency
Receiving Sensitivity
Communication Distance
Network Distance
Protocol
Working Temperature Range
Dimension
Specification
DC 3V (CR 2450)
30µW
2405-2480MHz
-97dBm
100m
50m
ZigBee HA
-25℃~+70℃
60*60*20.8mm

Smart Home - Water Leakage Sensor
- User Manual
www.amikohome.com
Introduction
Thank you for choosing AMIKO HOME Smart Water
Leakage Sensor.
AMIKO Smart Water Leakage Sensor uses ultra low
power consumption and ZigBee wireless network
technology. The battery lifetime is longer and the
design of the sensor protects the product from the
effects of high humidity environment. The sensor has
high accuracy and sensitivity. This product is designed
to be used in the basement, hotel room, water tower,
pool, swimming pool etc. for detecting water when
leaking. The Smart Water Leakage Sensor connects to
the smart home network via AMIKO Smart HUB and
sends alert on water leakage to the users’ mobile
devices via AMIKO HOME mobile application.
Caution
1. The product communicates wireless, please
don’t put the product in the metal box to
prevent the signal from shielding;
2. The temperature environment range is
between −25℃and +85℃; Humidity ≤ 95%RH.
3. Avoid using in the chemistry, combustible
gas, saturated salt fog or other abnormal
environment;
4. It should be installed in a place with no snow
and rain. The medium should be without gas or
dust that can corrode metal, destroy the
insulation and/or explode
.
Installation
1. Tear down
adhesive film, stick
the sensor to chosen
area
2. Proper installation
is shown on the
following picture:
Caution:
1. Install the sensor
wherever leaking can
be expected.
2. Please do not install the detector in a place where
rain, smoke or steam can be expected or which is
already under water.
Operation
1. Device must be paired with AMIKO Smart
HUB.;
2. Put the battery (2xAAA) into the sensor, put
back the plastic cover and long press the reset
button. As soon as the light on the device starts
blinking press OK button on HUB to join the
network.
3. Within 1 minute your water leakage sensor
will appear in Device Manager of AMIKO
HOME mobile application. You can see,
rename, assign to a room and/or manage your
device in the app.
Note: If failed, repeat the above procedure. If
failed after many attempts, please set back to
factory mode.
4. Your water leakage sensor is now ready to
send alerts to the application when detecting
water
5. Set back to factory mode: Long press smart
water leakage sensor’s reset button for about 8
seconds, the indicator light flashes 2 to 3 sec,
then blinks. Then the smart water leakage
sensor returns to factory settings.
Specifications
Performances
Working Voltage
Standby Power
Working Frequency
Receiving Sensitivity
Communication Distance
Network Distance
Protocol
Working Temperature Range
Detector Size
Senser Size
Specification
DC 3V (2xAAA)
15µW
2405-2480MHz
-97dBm
100m
50m
ZigBee HA
-10℃~+50℃
60*30*12.5mm
28.3*26.5*12.2mm
(1)
(2)

Smart Home - Smart Curtain Controller
- User Manual
www.amikohome.com
Introduction
Thank you for choosing AMIKO HOME Smart Curtain
Controller.
AMIKO Smart Curtain Controller works with ZigBee
protocol and it is designed to control curtain motors.
AMIKO Smart Curtain Controller is developed to work
with ZigBee protocol and it is designed to control
curtain/shader motors. The controller should be paired
with AMIKO Smart HUB so that the controller could
connect to the ZigBee wireless network. After pairing
your devices, you can easily control the curtain opening
and closing by using AMIKO HOME mobile
application. You can check or change the status of your
curtains, shaders, etc. with your mobile devices via
AMIKO HOME mobile application.
Caution
1. The product communicates wireless, please
don’t put the product in the metal box to
prevent the signal from shielding;
2. The temperature environment range is
between −25℃and +85℃; Humidity ≤ 95%RH.
3. Avoid using in the chemistry, combustible
gas, saturated salt fog or other abnormal
environment;
4. It should be installed in a place with no snow
and rain. The medium should be without gas or
dust that can corrode metal, destroy the
insulation and/or explode
.
Installation
Wiring method: Please connect the live wire and
neutral wire according to the following picture.
Operation
1. Your controller should be paired with an
AMIKO Smart HUB to connect to ZigBee
network.
2. Pairing: take off the glass cover from the
switch, you will find a small black button there.
This is for reset/pairing.
3. Please push the small black button for 3-5
secs.
4. Press the OK button on the AMIKO smart
gateway (HUB) for pairing. The gateway will find
the controler automatically.
5. Once the pairing is done, you will see the
Curtain Controller in the application’s Device
Manager
6. Remote control: you can control your devices
remotely via AMIKO HOME mobile application.
¹ Change to factory mode: long press the
controller’s Reset button for 5 seconds, the
network indicator flashes with blue light,
immediately let it go, this way the controller
disconnects from the ZigBee network. ² Click
the online device switch in the mobile client
device, and then click "..." in the upper right
corner, select delete, the indicator of the
controller flashes blue, the controller
disconnects from the ZigBee network.
Specifications
Performances
Power Voltage
Standby Power
Load Power
Working Frequency
Wireless output power
Protocol
Communication distance
Accessible Network Range
Receiving sensitivity
Operating Temperature
Dimension
Specification
AC 110V-265V
<0.5W
800W (Resistive load)
2405-2480MHz
20dBm
ZigBee HA
200m
100m
-101dBm
-25℃~+70℃
86mm*86mm*36mm
Neutral wire
Live wire
Curtain motor
Curtain motor

Warranty
The products are under warranty for one year,
except damage by improper use. The following
situations are beyond the scope of free
warranty.
a. Taken apart and maintained by unauthorized
maintenance center.
b. Damage by flood, fire, thunder and other
natural disasters.
c. Damage by extrusion, flood, dampness or
other artificial damage.
d. Broken down by improper use of the
product, not according to the user manual
www.amikohome.com