Ammara Designs PBS-RGH User manual

VALVE ONLY
For Pressure Balance Shower Set
No Finish
PBS-RGH
15121422-A
Installation Instructions
For easy installation of your faucet you will need:
●To read all the installation completely before beginning.
●To read all warnings, care, and maintenance information.
Applicable Standards/Codes
Installation Dimensions
PBS-RGH
Replacement Parts
15121422-A 4
NO. Description Part No.
1
End Cap 5T1C0138NT
2
3
Stop Valve 9Q1152NT
5L0C0861NT
4 Pressure Balance Cartridge 5D0M0262PL
5
Sleeve
9Q1173NT
6
Cartridge Nut 5T1C0216NT
Sten & Threaded Nipple
IAPMO certified to meet or exceed the following:
• ASME A112.18.1/CSA B125.1
• Uniform Plumbing Code
• National Plumbing Code of Canada
• ASSE 1016
2 7/8＂- 3 7/8＂1 13/16＂- 2 13/16＂
5 1/2＂- 5 7/8＂
1 1/4＂
11/16＂5＂
1 11/16＂
2 1/16＂
2 15/16＂
5 1/4＂
4 1/8＂
1/2"-14 NPT
1/2"-14 NPT
1/2"-14 NPT
2
1
3
4
56

PBS-RGH
Installation Instructions
23
15121422-A 2 15121422-A3
3
Using mounting holes secure the
valve making sure the “UP” label
outlet is on top.
If you are making a back-to-back
installation (hot on right and cold on
the left) ,install the back valve body
as described in steps #5 – #6.
If not, go to step #7. NOTE: Notice
that the back valve has hot and cold
indicators that will be opposite of the
incoming supply lines.
45
Remove the cartridge and stem
assembly. Notice that the pin is at
the top. Rotate the cartridge 180°.
The pin should be on the bottom.
This valve is designed to fit into a
wall that is 2 7/8＂to 3 7/8＂from
finished wall to the back of the valve.
Extensions are shipped with the trim
if necessary.
12 7/8＂- 3 7/8＂2
Turn off the water supplies.Install the
valve so the finished wall will fit
between the markers on the mud
guard.
22 7/8＂-3 7/8＂
6
Align the pins on the bottom of the
cartridge and push the cartridge into
the valve. Make sure the cartridge is
firmly installed into the valve body.
Reinstall stem assembly with mud
guard.
7
Connect valve body to water supplies using the proper fittings .
Warning: avoid soldering at high temperature. Exposure to high
temperature may damage the cartridge. Be sure stops and pressure balance
cartridge are removed before soldering.
8
Connect the valve body to the shower
outlet with the proper fillting.Note: it
is suggested that you anchor all water
lines.
Stops
Pressure Balance
Cartridge
Warning
Mounting
hole
Mounting hole
Hot
Left Right
Back valve Back valve
Cold
2
9
1.Pressure test and flush the valve.
a. Prior to testing, remove mud guard, stem assembly, cartridge as stops as shown.
b. Plug the shower outlet and check for leaks.
c. After testing, flush system.
d. Remove shower outlet plug. Re-install the stops, cartridge, stem assembly and mud guard.
2.Check for leaks.
Installation completed.
10
a b c d
Cartridge
Rotate 180°
Pin
Pin
Pin
Valve Cartridge
Red
Red
Red Blue Blue
Blue

PBS-RGH
Installation Instructions
23
15121422-A 2 15121422-A3
3
Using mounting holes secure the
valve making sure the “UP” label
outlet is on top.
If you are making a back-to-back
installation (hot on right and cold on
the left) ,install the back valve body
as described in steps #5 – #6.
If not, go to step #7. NOTE: Notice
that the back valve has hot and cold
indicators that will be opposite of the
incoming supply lines.
45
Remove the cartridge and stem
assembly. Notice that the pin is at
the top. Rotate the cartridge 180°.
The pin should be on the bottom.
This valve is designed to fit into a
wall that is 2 7/8＂to 3 7/8＂from
finished wall to the back of the valve.
Extensions are shipped with the trim
if necessary.
12 7/8＂- 3 7/8＂2
Turn off the water supplies.Install the
valve so the finished wall will fit
between the markers on the mud
guard.
22 7/8＂-3 7/8＂
6
Align the pins on the bottom of the
cartridge and push the cartridge into
the valve. Make sure the cartridge is
firmly installed into the valve body.
Reinstall stem assembly with mud
guard.
7
Connect valve body to water supplies using the proper fittings .
Warning: avoid soldering at high temperature. Exposure to high
temperature may damage the cartridge. Be sure stops and pressure balance
cartridge are removed before soldering.
8
Connect the valve body to the shower
outlet with the proper fillting.Note: it
is suggested that you anchor all water
lines.
Stops
Pressure Balance
Cartridge
Warning
Mounting
hole
Mounting hole
Hot
Left Right
Back valve Back valve
Cold
2
9
1.Pressure test and flush the valve.
a. Prior to testing, remove mud guard, stem assembly, cartridge as stops as shown.
b. Plug the shower outlet and check for leaks.
c. After testing, flush system.
d. Remove shower outlet plug. Re-install the stops, cartridge, stem assembly and mud guard.
2.Check for leaks.
Installation completed.
10
a b c d
Cartridge
Rotate 180°
Pin
Pin
Pin
Valve Cartridge
Red
Red
Red Blue Blue
Blue

VALVE ONLY
For Pressure Balance Shower Set
No Finish
PBS-RGH
15121422-A
Installation Instructions
For easy installation of your faucet you will need:
●To read all the installation completely before beginning.
●To read all warnings, care, and maintenance information.
Applicable Standards/Codes
Installation Dimensions
PBS-RGH
Replacement Parts
15121422-A 4
NO. Description Part No.
1
End Cap 5T1C0138NT
2
3
Stop Valve 9Q1152NT
5L0C0861NT
4 Pressure Balance Cartridge 5D0M0262PL
5
Sleeve
9Q1173NT
6
Cartridge Nut 5T1C0216NT
Sten & Threaded Nipple
IAPMO certified to meet or exceed the following:
• ASME A112.18.1/CSA B125.1
• Uniform Plumbing Code
• National Plumbing Code of Canada
• ASSE 1016
2 7/8＂- 3 7/8＂1 13/16＂- 2 13/16＂
5 1/2＂- 5 7/8＂
1 1/4＂
11/16＂5＂
1 11/16＂
2 1/16＂
2 15/16＂
5 1/4＂
4 1/8＂
1/2"-14 NPT
1/2"-14 NPT
1/2"-14 NPT
2
1
3
4
56