Amped Wireless AD14EX User guide

1 2
Remove the antenna from you wireless device Connect the Jumper Cable to the Premium Surge Protector
Check your package contents:
High Power 14dBi Outdoor
Directional WiFi Antenna
Premium Indoor Jumper Cable
(N-Type Male to RP-SMA Connectors)
Premium Surge Protector
Antenna Mounting Kit
What you’ll need to get started:
802.11b/g/n Wireless Router,
Access Point, Bridge, Repeater
or Wireless Device with RJ-SMA
or N-Type female connector
Premium 25ft Outdoor WiFi
Antenna Cable
(Sold Separately)
Installation Instructions
Attach the Jumper Cable to the antenna connector using the side with the RP-SMA connector.
4
Installation Overview
Connect the other end of the Jumper
cable to the included Premium Surge
Protector.
Use the Premium 25ft OutdoorAntenna cable (Sold Separately) to:
a) Connect one end to the Surge Protector and
b) Extend your installation outdoors
3a
21
3
4
2
Using the included 3ft Jumper Cable, attach
the SMA Plug to the RJ-SMA antenna
connector on your wireless device.
1
(Sold Separately)
Wireless Device*
PreConnect the Premium 25ft
Outdoor WiFi Antenna Cable
(Sold Separately) to the High Power
14dBi Outdoor Directional Wi-Fi
Antenna.
Premium Surge Protector
Jumper Cable 3b
AD14EX
Ground
* Note: If you have a wireless device with an N-Type Female connector, then simply connect the Premium 25ft Outdoor WiFi Antenna Cable APC25EX between your wireless device and the High PowerAntenna.
The Premium Surge Protector and Jumper Cable are not required, but are used with your wireless device for safety precautions to prevent damage from electrical surges.
or
3Ground the Premium Surge Protector
Ground
— R E A D F I R S T —
SETUP MANUAL
High Power Outdoor 14dBi Directional WiFi Antenna Kit
(Sold Separately)
Wireless Device
Find the N-Type connectors on the Premium Surge Protector.
4Connect the Premium Outdoor Antenna Cable to
the Surge Protector
Find the N-Type female connector on
the Surge Protector and attach either
end of the Premium Outdoor Cable to
the Surge Protector. Run the other
end of the cable to the location
where you plan on installing the High
Power Antenna.
5Mount the Antenna
Before you attach the other end of
the Outdoor Antenna Cable to the
High Power Antenna, it is important
that you first mount the High Power
Antenna securely. Use the antenna
mounting instructions on the back to
securely mount the High Power
Antenna.
6Attach the Outdoor Antenna
Cable to the High Power
Antenna
Locate the N-Type male connector
from the Outdoor Antenna Cable and
fasten it tightly to the N-Type female
connector of the High Power Antenna.
APC25EX
(Sold Separately)
Surge Protector
Jumper Cable Jumper Cable
APC25EX
(Sold Separately)
Ground
AD14EX
APC25EX
AD14EX
Fasten a standard copper wire to the ground
wire connector on the Premium Surge Protector.
Ground or fasten the opposite end of the copper
wire to a metal stake that is fastened to the
earth. Properly grounding the Surge Protector
will protect your equipment from high voltage
electrical surges by allowing the earth to absorb
the electrical surge.
Amped Wireless
A Division of Newo Corporation
Copyright © 2011 Amped Wireless / Newo Corporation. All rights reserved.
Amped Wireless, Newo Corporation, the Amped Wireless Logo are registered trademarks or trademarks of Newo Corporation.
All other trademarks herein are the property of their respective owners. No affiliation is expressed or implied.

Mounting Instructions
Pole Mounting:
Antenna Operating Tips:
Two High Power Antennas are better than One:
To get the most out of your High Power Wireless Antenna, it is always recom-
mended that you use multiple antennas (one on each side of your connection).
High Power Wireless Antennas increase the transmit power of your wireless device
by concentrating the wireless signal from your wireless device. In order to
achieve optimal range, it is recommended that a high gain antenna is used on
each end of your wireless connection.
High Power Amped Wireless WiFi devices also help to increase the overall range of
your wireless application. Amped Wireless High Power Wireless products include
power amplifiers that boost both receiving and transmitting strength.
Tx
Rx Downlink Tx
Rx
Tx Strong Transmit Signals
Rx Strong Receive Signals
Not Optimized Wireless Signals
One Antenna = Not Optimized
Bridge Access Point
Signal Pattern
Omni-Directional Coverage
Side View
30°
Top View
Tx
Rx Downlink Tx
Rx
Tx Strong Transmit Signals
Rx Strong Receive Signals
Access Point
Bridge Two Antenna = Good Connection
Correct InstallationIncorrect Installation
Optimal Antenna Coverage
30°
Antenna Positioning:
High Power Antennas have antenna gain levels that are much higher than standard
wireless antennas. By concentrating the wireless signal, High Power Antennas
modify the signal pattern of your wireless device. It is important that you under-
stand the wireless output pattern of your High PowerAntenna (right) so you may
carefully position it to your desired output location. If you feel that you are not
getting the wireless range and performance from the antenna, you may need to
adjust the position of your antenna until the desired performance is achieved.
Check the signal strength of your setup using the user interface of your WiFi
device or through a 3rd party WiFi network analyzer software.
Wall Mounting:
Pole Wall
1
2
3
4
5
6
7
8
9
10
13 12 11
1 Antenna x1
2 L Bracket (1) x1
3 M5 Washer x 4
4M5 Nut x45 M6 Nut x4
6M6 Split Lock Washer x 4
7
Wall Screw x 4
8
Wall Anchor x 4
9
10
11 L Bracket (2) x 1
12 M6 Washer x4
13 M6 Bolt x4
M5 Split Lock Washer x 4
M6 Washer x 4
1
2
3
4
6
8
10 7
1 Antenna x 1
2 M5 Washer x 4
3M5 Nut x 44 M6 U-bolt x 25
6
M6 Split Lock Washer x 4
7
M6 Nut x 4
8
L Bracket x 1
9
10
M6 Washer x 4
Link x 2
M5 Split Lock Washer x 4
5
Instructions and parts needed
Instructions and parts needed
9
Rely only on high-grade computers & hardware on our virtual shelves.