Amrotec CC-01 User manual

User Manual V.1
CC-03 Model Coin Counter
CC-Series
Heavy-duty with Conveyor

Preface
__________________________________________________________________________________
This guide provides information about the AMROTEC® Electronic coin counters. We recommend
reading this guideline to learn how to use this machine. Then, as you become more familiar with this
machine, use it as a reference guide to look up information when you need it.
CC-Series Coin Counters
Model Coin Hopper
approx
Speed
approx Off-Sorting Conveyor Belt Driven
External
Remote
Display
Foot
Paddle
CC-01 1500 dimes 3400 dimes ● X ● ●
CC-03 4300 dimes
3400 dimes
● ● ● ●
FCC Compliance Statement
FCC Notice
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses and
can emit radio frequency energy and, if not installed and used in accordance with
the instruction manual may cause harmful interference in radio communications.
Operation of this equipment in a residence area is likely to cause harmful
Interference in which case the user will be required to correct the interference at his
own expense.
THIS DEVICE COMPLIES WITH PART 15 OF FCC
RULES. OPERATION IS SUBJECT TO THE
FOLLOWING CONDITIONS:
1. THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE
UNDESIRED OPERATION.
Changes or modifications of this product not expressly approved
by Amro-Asian Trade, Inc., could void the user’s authority to
operate the equipment.

3
of
17
Table of Contents
Table of Contents .................................................................................................................................... 3
1. Introduction and intended use......................................................................................................... 4
Safety information ............................................................................................................................... 4
Warnings............................................................................................................................................. 4
Front / Rear view................................................................................................................................. 5
User interface...................................................................................................................................... 6
Display................................................................................................................................................. 6
Key chart............................................................................................................................................. 6
3. Installation........................................................................................................................................ 7
Environment and working space......................................................................................................... 7
Bag, box installation............................................................................................................................ 8
4. Setting the coin size......................................................................................................................... 9
5. Coin preparation............................................................................................................................ 10
6. Operation....................................................................................................................................... 10
Counting............................................................................................................................................ 10
Select Denomination......................................................................................................................... 10
Memory ............................................................................................................................................. 11
Add Memory...................................................................................................................................... 11
Show Memory ................................................................................................................................... 11
Bag Stop............................................................................................................................................ 11
Select bag stop.................................................................................................................................. 11
Clear incomplete bag ........................................................................................................................ 12
7. Setting menu.................................................................................................................................. 12
System Setting.................................................................................................................................. 12
Screen display................................................................................................................................... 13
Counting mode.................................................................................................................................. 13
Batch selection.................................................................................................................................. 13
Deno/ Batch setting........................................................................................................................... 13
8. Maintenance.................................................................................................................................. 14
10. Certifications.............................................................................................................................. 16
11. Specifications............................................................................................................................. 17
12. Accessories ............................................................................................................................... 17

4
of
17
1. Introduction and intended use
The CC-03 is a medium to heavy-duty high-speed counter with automatic coin feeding system for
coins and tokens. It is designed to count large volumes of coins standardized for all six US coins. The
pre-selected coin size will be counted while smaller coins are being rejected without slowing down the
counting speed. The count result can be accumulate in value or piece. Besides, variable bag stops
and count memory the CC-03 offers many useful features to meet your requirements.
An electric coin counter is mainly used for processing coins in financial institutions, vending
businesses, amusement parks, payphone businesses, transportation companies, and other
coin-op businesses.
CC-Series Electric Coin Counters count and separate all US coins at a fastest speed into a bag. You can
also roll coins into standard paper wrapper using accessories provided with this machine. Two
independent adjustment knobs on the machine allow users to select coin diameter and thickness for
processed coins or to separate mixed coins
Safety information
• Always follow basic safety precautions when using this product to reduce risk of injury
from fire or electric shock.
• Observe all warnings and instructions marked on the product.
• Do not install or use this device outdoors, near water, or when you are wet. Install the
product securely on a stable surface. See also chapter “Installation”
• Do never exceed the specified load of the bag, given in chapter “Installation”. Otherwise the
machine can tilt and drop down.
• Do not touch the coin disc when it isin operation. Take extra care oflong hairs or loose
clothing (e.g. tie). If it is caught in the machine, switchoff the power immediately.
• Unplug the CC-03 from wall outlets before cleaning.
• Do not clean the machine with chemical cleaner and do not use blowing gas. Otherwise parts
can be damaged or explosion / flash may occur.
• If the product does not operate normally, see chapter “Troubleshooting”.
• Do not operate the machine when covers are removed. Servicing must be carried out by
qualified service personnel.
Warnings
On the machine and in this manual standardised warning symbols are used. These are explained as
followed:
Warning
Warning of possible danger, such as moving parts.
Electrical danger Warning of possible injuries through electrical shocks
Risk of tilting
Warning of possible device tilting.
Do not exceed the weight of 40lbs in the counting bag and 15lbs
in the reject bag. (see also Chapter “Installation”)

5
of
17
2. Machine overview
Front / Rear view
Coin hopper
Hopper door (service access)
Display
Coin thickness adjuster
Keyboard
Coin diameter adjuster
Right top cover (service
access)
Count exit with
Quick-change
switch
Reject exit
Carry handle
Power socket
and Main switch
Foot pedal connector
Printer and external Display
port (RS232)
USB port
Network LAN Ethernet

6
of
17
User interface
Display
Bag stop level (1 or 2) Time
Number or Value of counted coins
Memory (Total of saved counts)
Selected coin number Number of coins in bag
Function keys
Denom
(in Valu
ination
e mode)
Key chart
Key Description Normal key stroke 3 seconds key stroke
Start/ Stop Start or stop counting
Add memory Add the count to the memory
Print Print ticket
Batch stop Set batch stop Clear bag content
Clear Delete count result and bag content Delete memory
Denomination Select new denomination or coin
number. Show memory total.
Setting Enter setting menu
Help Show key functions

7
of
17
3. Installation
Environment and working space
• Make sure the environment does comply with the specifications given in chapter 1.1
and 11. Make sure the CC-03 has proper electrical grounding.
• The main fuse protection must be minimum 1,5A.
• Install the CC-03 where no one can step on it or trip over the line cord, and the line cord
cannot be damaged.
• The installation area must be stable, solid, and smooth.
The bagging unit of the machine must protrude the table edge so that the connected bag hangs freely.
But please make sure that the front feet of the CC-03 remain in full size on the desk.
Count exit with
Bagging unit
Reject exit
Bag Front feet
Table edge
When the CC-03 is on its working position, adjust the support stand to the same level with the table
surface.

8
of
17
Bag, box installation
The CC-03 has one counting and one reject exit. The counting exit is provided to clamp a coin bag on
it, but can be also used for the optional tubing kit. On the reject exit a cup or a bagging unit can be
attached. When using the reject bagging unit the CC-03 must be placed on the left side of the desk,
so the reject bag hangs freely.
Warning of possible device tilting.
Do not exceed the weight of 40 lbs/18Kgs (about 2000x $1 coins) in the counting bag and 15lbs
/7Kgs (about 800x $1 coins) in the reject bag. Install a support shelf where the bag rest on it, if higher
weights are in use.
Connect the reject cup or reject bagging unit
A bag is fixed by: Move the metal ring upwards, wrap the bag around the tube and clamp it by moving
down the ring.
18
KG
7KG

9
of
17
4. Setting the coin size
Before you start counting, set always the thickness and diameter according the coin size you want to
count.
Note: Smaller coins will rejected but larger coins stay in the machine and may cause jams.
If tokens or other coins need to be count, those are not marked on the scale, set the correct size as
follow:
Note: Do not open or close the Right top cover with open Hopper door!
a) Thickness
Open the right top cover and the hopper door. Turn the Thickness adjuster to maximum. Place the
token under the thickness block and turn the adjuster slowly down until it gently touch the token.
Turn the adjuster backward until the token moves freely, without resistance, between disc and
thickness block.
b) Diameter
Lift up the transport belt. Turn the Diameter adjuster to maximum. Place the token on the transport
track and turn the adjuster slowly narrow until it gently touch the token. Turn the adjuster
backward until the token moves freely and has side clearance of about 0.4mm.
Thickness adjuster
Diameter adjuster

10
of
17
5. Coin preparation
Before loading coins into the machine inspect and remove all foreign objects. Also sort off damaged,
lubricated or sticking coins.
6. Operation
Make sure the hopper door is closed and fill the coins in the hopper. Before counting make always
sure the selected settings, denominations and count memories meet your approbations.
Counting
Press “On/Off” key to start the count, or push the coin exit to activate the Quick-change switch. The
CMX10 shows the counted quantity or value. When the count is finished the CMX10 stops
automatically. (You can also press “On/Off” or push again the coin exit to stop the count manually.)
Piece counting Value counting
or
It is now possible to
P: Print the count
M: Save the count into the memory
C: Clear the count and bag content
C (long): Clear the count memory of this denomination
On/Off: Count more coins
The CC-03 stops with message “B1 Stop” (or “B2”) if the pre-selected stop is reached. The count will
automatically transferred to the memory and the bag content counter will set to zero. Replace the bag
with an empty one.
Note: Value or piece counting is selectable in Setting menu, option “Countingmode”
Select Denomination
Adjust the thickness and diameter knob to the desired coin size and mount an empty coin bag on the
counting exit.
Press the “0” key several times until the requested denomination / coin number appears.
If the count or bag content were not zero, there will be a warning message: “Are you sure you want to
proceed”. If you press “1” (Yes) the two counters will automatically cleared. With “2” (No) the coin
number will not be changed.
After the last coin number “9” a total symbol ” appears. It represents the sum of all saved counts and
cannot used for counting.
B1 10:45
Count
100
Total
0
# 1 B 1000 100
0
#
1 2
?
B1 10:45
Value
200.00
Total
0.00
# B 1000 100
0
2.00
1 2
?