INFLATION AND ASSEMBLY
OF THE FLOAT TUBE:
1) PLACE THE FLOAT TUBE FLAT ON THE FLOOR WITH THE
VALVES FACING UPWARDS.
2) INFLATE THE FLOAT TUBE TO A MAXIMUM PRESSURE
OF 0.8 BAR
3) INFLATE THE SEAT TO A MAXIMUM PRESSURE OF 0.8 BAR
4) JOIN THE TWO PIECES OF THE SPREADER BAR BY PLACING
BOTH ENDS ANGLED OUTWARD.
5) INSERT THE SPREADER BAR INTO THE ENVELOPE OF THE
RECEIVING MAT AND PLACE IT IN THE TWO LOCATIONS AT
THE ENDS OF THE BLADDERS.
GETTING IN THE WATER:
1. START ON A SLIGHT SLOPE (SUCH AS A BOAT RAMP).
2. PUT YOUR FINS ON AND THEN PUT THE FLOAT TUBE IN THE
WATER (IDEALLY THE WATER SHOULD REACH YOUR KNEES).
TAKE A SEAT ON BOARD BY ENTERING FROM THE OPEN SIDE
AND THEN TURN SO THAT YOUR BACK IS FACING THE BACK
OF THE SEAT.
3. SIT ON BOARD THE FLOAT TUBE, HOOK THE LANDING MAT
BACK ON AND LET YOURSELF FLOAT AWAY. PRACTISE USING
YOUR FINS TO BACK UP AND TURN.
CARE AND STORAGE
OF THE FLOAT TUBE
IT IS IMPORTANT TO RINSE YOUR FLOAT TUBE THOROUGHLY
WITH CLEAN WATER AFTER EACH USE. ALWAYS ENSURE
THAT THE BLADDERS ARE PARTIALLY DEFLATED BEFORE
STORING THE ASSEMBLED FLOAT TUBE IN A WARM VEHICLE
OR ROOM. THE AIR INSIDE THE INNER TUBES CAN EXPAND
CONSIDERABLY. IF THE FLOAT TUBE WILL NOT BE USED FOR
AN EXTENDED PERIOD OF TIME, DEFLATE IT AND STORE IT.
TO PREVENT MOULD GROWTH, MAKE SURE THE FLOAT TUBE
IS DRY BEFORE PACKAGING AND STORE IT IN A DRY PLACE.
GARANTEE
1. THE WARRANTY IS VALID FROM THE DATE OF PURCHASE.
2. THE WARRANTY IS VALID ONLY IF THIS PRODUCT IS FOR PERSONAL USE ONLY.
3. AMTRAC FISHING WILL MAKE THE FINAL DECISION REGARDING THE WARRANTY, WHICH MAY REQUIRE INSPECTION AND/OR PHOTOS
OF THE EQUIPMENT THAT CLEARLY PROVE THE DEFECT(S). IF NECESSARY, THIS DOCUMENT SHOULD BE SENT TO THE DEALER IN YOUR
COUNTRY AT THE OWNER’S EXPENSE. THE PRODUCT CAN ONLY BE RETURNED IF THE AMTRAC FISHING DEALER HAS GIVEN A RETURN
AUTHORIZATION NUMBER. THIS MUST BE VISIBLE ON THE OUTSIDE OF THE PACKAGE OR IT WILL BE REFUSED.
4. IF A PRODUCT IS FOUND TO BE DEFECTIVE BY AMTRAC FISHING, THE WARRANTY COVERS REPAIR OR REPLACEMENT OF THE DEFECTIVE
PRODUCT ONLY. AMTRAC FISHING WILL NOT BE RESPONSIBLE FOR ANY COSTS, LOSS OR DAMAGE INCURRED AS A RESULT OF LOSS OR
MISUSE OF THE PRODUCT.
5. THIS WARRANTY DOES NOT COVER DAMAGE CAUSED BY MISUSE, ABUSE, NEGLECT, NORMAL WEAR AND TEAR. SIMILARLY, IT IS NOT
LIMITED TO PUNCTURES, DAMAGE DUE TO EXPOSURE TO EXCESSIVE HEAT, DAMAGE CAUSED BY IMPROPER HANDLING OR STORAGE, AND
DAMAGE NOT RELATED TO THE INTRINSIC QUALITY OF THE MATERIAL AND WORKMANSHIP.
6. THIS PRODUCT MUST NOT BE MODIFIED AND/OR EQUIPPED WITH A MOTOR.
7. THIS PRODUCT SHOULD NOT BE USED BEYOND THE RECOMMENDED MAXIMUM LOAD CAPACITIES.
8. THIS WARRANTY IS VOID IF AN UNAUTHORIZED REPAIR HAS BEEN MADE, OR IF ANY PART OF THE FLOAT TUBE HAS BEEN CHANGED OR
MODIFIED.
9. THE WARRANTY FOR ALL REPLACEMENT EQUIPMENT IS EFFECTIVE FROM THE DATE OF PURCHASE.
10. THE ORIGINAL RECEIPT OF PURCHASE MUST BE ENCLOSED FOR ALL WARRANTY CLAIMS. THE NAME OF THE RETAILER AND THE DATE
OF PURCHASE MUST BE CLEAR AND LEGIBLE.
11. NO WARRANTY WILL EXTEND BEYOND THE WARRANTY SPECIFIED HEREIN.
12. WARRANTY IS NOT INHERITABLE. IT CANNOT BE TRANSFERRED BETWEEN OWNERS.
