Analog way MSQ04-MkII User manual
Picturall Quad Mark II
Ref. MSQ04-MkII
QUICK START GUIDE
Thank you for choosing Analog Way and the Picturall Quad Mark II. By following these simple steps, you will
be able to set up and use your Powerful media server within minutes. Discover the Picturall Quad Mark II
capabilies and intuive interface while commanding top-notch presentaons and unleash your creavity
for a new experience in show and event management.
• 1 x Picturall Quad Mark II (MSQ04-MkII)
• 1 x Power supply cord (or 2x with oponal redundant PSU)
• 1 x Ethernet cross cable (for device control)
• 1 x USB memory sck containing soware and technical documentaon
• 1 x Rackmount kit
• 1 x User manual (PDF version)*
• 1 x Quick start guide*
* User Manual and quick start guide are also available on www.analogway.com
Go on our website to register your product(s)
hp://bit.ly/AW-Register
WHAT’S IN THE BOX
QUICK SETUP & OPERATION
CAUTION!
Damage caused by improper
rack mounng will not be cove-
red under warranty.
Register
your product
The Picturall Quad Mark II uses standard ethernet
LAN networking. To access the Web Congurator,
connect a computer to the Picturall Quad Mark II
using the Ethernet cable. Then on your computer,
open an internet browser and enter the IP address
of the Picturall Quad Mark II (displayed on the
front panel screen).
The connecon should start.
Oen, computers are set to DHCP client (automac
IP detecon) mode. You may need to change the
IP address conguraon on your computer before
you can connect. These sengs are found in the
properes for your LAN network adaptor, and vary
by operang system.
The default IP address on the Picturall Quad Mark II
is 192.168.2.140 with a netmask of 255.255.255.0.
Therefore, you can assign your computer a stac
IP address of 192.168.2.100 and a netmask of
255.255.255.0 and should be able to connect.
If the connecon is not starng:
• Make sure the computer IP address is on the
same network and subnet as the Picturall Quad
Mark II.
• Make sure that no devices have the same IP
address (prevent IP conicts)
• Make sure the network cable is CAT5 or higher.
• For more informaon, please see the user manual
or contact your local technical support.
Once successfully connected, the Web Congurator
is displayed automacally.
2x balanced XLR inputs (for mecode LTC)
and 2x balanced XLR outputs
(Oponal audio interface)
OLED display
To turn o, press this buon
then press the Next/Status buon to conrm
USB Plug
Display and cycle status
informaon on the OLED display
100-240 VAC; 12-7A; 50/60Hz; 1200W;
internal, autoswitchable
- 2 x HDMI 1.4,
- 4 x HDMI 1.4,
- 1 x HDMI 2.0,
- 2 x HDMI 2.0,
- 2 x 3G-SDI,
- 4 x 3G-SDI,
- 2x 1Gb Ethernet
(one card per
device)
The user should avoid disconnecng the power source
(AC input) unl the unit is in stand-by mode. Failure to
do this could result in hard drive data corrupon.
USB Plug
- 2x USB Ports
- 2x 10Gb/s Ethernet Plugs
for control, network streams
(H264, NDI, etc.)
or Dante audio (32 channels)
Genlock (Oponal)
Four DisplayPort 1.2 outputs
(4K@60Hz 10-bit)
- 2 x HDMI 1.4,
- 4 x HDMI 1.4,
- 1 x HDMI 2.0,
- 2 x HDMI 2.0,
- 2 x 3G-SDI,
- 4 x 3G-SDI,
The operang systems must support Java version 8 for Picturall
Commander to be installed. Make sure Java version 8 is installed on
the computer before installing Picturall Commander.
Note: The latest version of Commander is automacally down-
loaded during the installaon process.
1. On the computer, insert the USB sck delivered with the media
server.
2. Copy the installer le matching the operang system from the
USB sck to the computer.
3. Run the installer le and follow the instrucons to complete the
installaon process.
In the Display conguraon menu, choose the display mode:
- Auto: follow EDID sengs
- Manual: set the output resoluon, refresh rate and connectors
manually
- : select a custom display conguraon
- Special: select a preset mode for display signal spliers (Analog
Way DPH104, Matrox TH2GO and DH2GO, Datapath X4 and FX4)
In Manual mode, select the output connectors, resoluon and
refresh rate for the selected GPU.
Note: Do not use mulple display devices with dierent refresh
rates as this may cause bad playback (stuering).
Tip: If using idencal displays, use the buons Copy, Paste and
Copy to all.
In the DMX conguraon menu, choose the DMX/Art-Net
sengs:
- : Set the rst universe and the rest of the
layers will be patched to next universes. If patching more than 9
layers, the server will use several Art-Net universes.
- Art-Net subnet: Set the Art-Net subnet value (between 0 and
15).
- : Set the rst channel of the rst universe for
layer 1.
- : Set the preferred DMX xture prole (1.1, 1.0 or
mini).
- : Enter the number of the displays
controlled with DMX t as the acve displayed plug. (Not
necessarily displayed).
Layers are patched rst starng from a given oset on a given
universe. Layers are patched so that they do not split at the
universe border.
CONNECTION TO THE MEDIA SERVER
1. Connect the computer and the Media Server to the same
network.
2. Use same netmask in the server and the computer if not
using DHCP server. If DHCP server is enabled in the server, use
automac network sengs in the computer.
3. Run Picturall Commander and click on the
tab.
4. Type the IP address of the server in the Address eld or click
Locate to automacally nd the servers in the same network and
view the server versions before connecng.
5. In the eld, enter a name for the connecon.
6. Click to Create the Connecon. A message conrms the
connecon to the Picturall Series Media Server.
- Launch a web browser and enter the server IP address in the
address bar. All devices default IP addresses are 192.168.2.140.
- Click or to access server
conguraon.
- Set the number of layers to use and patch to
Art-Net (max 200). This aects the number of available layers in
Picturall Commander.
- Set the maximum resoluon to be
processed by the media server.
CONTROL TABS
Click Window then click any menu to open the corresponding
control panel.
- : Connect and reconnect to a server pressing
Reconnect buon.
- Media: Transfer media les to the Picturall Series Media Server
and arrange the media library.
- Displays: Congure the display setup.
- Genlock: Synchronize all outputs with a Genlock signal.
- Layers: Control all layer parameters. This is the main menu
for controlling the Picturall Series Media Server with Picturall
Commander.
- GPUs: Opmize the use of the GPUs.
- : Schedule and synchronize cues with server clock,
media me, other cues, MTC and LTC.
- Cues: Program and me cues for the show.
- : Congure test images to help when seng up the
show.
- : Check the performance and temperature of the
server.
In the Server conguraon menu, choose the network mode:
- Automac (DHCP): The server gets IP address from DHCP
server in the same network
- Automac (ARTNET): The IP address is generated based on the
Art-Net protocol
- Manual: Set the IP address and netmask manually
INSTALLATION
PICTURALL COMMANDER
01-JUN-2021
MSQ04-MkII - QSG
Code : 140220
For complete details and operaons procedures, please refer to the User
Manual and our website for further informaon:
This Analog Way product has a 3 year warranty on parts and labor, back to factory. This warranty does not
include faults resulng from user negligence, special modicaons, electrical surges, abuse (drop/crush),
and/or other unusual damage. In the unlikely event of a malfuncon, please contact your local Analog Way
oce for service.
MEDIA
DISPLAYS
CUES
WARRANTY AND SERVICE
PICTURALL COMMANDER STRUCTURE
- Import media les via drag and drop le.
- Encode to AWX format for best
performance.
- Add web pages and video streams.
- Arrange medias in collecons (playlists).
- Set displays to match the conguraon.
- Follow the display wizard to create
Blendings.
- Use Cropping and Color correcon and
Angle correcon.
- Opmize GPUs performance
- Use Cues to save presets for several
layers.
- Create sequences for the show.
- Set Wait, Fade and Hold mings for the
Cues.
- Organize Cues in Stacks.
- Use Playbacks to play the Cue Stacks.
- Set me synchronizaon for mecode
triggered cues.
LAYERS
- Place the layers in the pixel canvas.
- Put medias in layers and play them.
- Set play mode end acon (Stop, Loop, etc.).
- Use various eects (rotaon, keying, cut
and ll, etc.).
- Use Macros to save sengs for one layer.
This manual suits for next models
1
Table of contents
Other Analog way Server manuals
Analog way
Analog way Picturall Series User manual
Analog way
Analog way Picturall Series User manual
Analog way
Analog way MSTC02-R2 User manual
Analog way
Analog way Picturall Series User manual
Analog way
Analog way Picturall MST02-R1 User manual
Analog way
Analog way Picturall Series User manual
Analog way
Analog way Picturall MSQ04-R1 User manual
Analog way
Analog way Picturall Series User manual
