ancnoble GG-005 Operating and safety instructions

Standard Package
GG-005C-2
GG-005C-1

Pressure Regulator
(optional)
1. The valve of GG-005C is USA hose
standard of NH-11.5, user can
screw to faucet directly.
2. Before installation, prepare some
water outlet connector, pipes,
drippers, etc. if needed.

6. Connect the sensor and solar panel, as shown in the following figure:
Note: The connector is waterproof，Please align
the convex & concave before inserting and
tightening.
Connect moisture
sensor
Connect solar
panel

7. Please refer to the following picture for connected solar panel and sensor
Note: Recommend to connect the controller valve to water source in first and then water out.
Finally connects sensor and solar panel.

8. Install the 4xAA rechargeable battery into the battery box on
the back of controller

After the controller is installed, bury the sensor in the position which would been
irrigated properly, fix the solar panel to place with sun, set control parameters and put
the purple waterproof cover over the controller.

How to use bury sensor
1. Bury the sensor according to crop root system. If root system is shallow and small,
such as vegetables, insert into the ground as shown, if root system is large and deep
such as tree, bury deep to the soil.
2. If using the sensor as a rain sensor, bury the sensor where is no irrigation water can
reach.

How to fix solar panel
User can fix the solar panel according to site. As shown in the following picture, tied
the solar panel to the fence. It is recommended to choose a place with plenty of sun.

Power on
Push and hold [Power] key until two beeps to turn on.

Timer and Moisture mode switching
Push and hold [Menu/Mode] key to switch to operating mode one
by one

One key to setup Dry/Wet Control Level
1) When the soil is just dry to the point of needs irrigation, push and hold [Dry Ctrl]
key until there is a beep, (Two beeps means successful learning. One beep means
fail). Then the valve will open and start watering. This dry moisture level will be
remembered as start irrigation threshold.

2) When soil reached wet point to end irrigation, push and hold [Wet Crtl] key
until there is a beep, (Two beeps means successful learning, one beep means fail.)
The valve will close; this wet level will be remembered as turn off point.
One key to setup Dry/Wet Control Level

Adjust Dry/Wet Control Levels
Push [Menu] key to browse, when browse into “Dry Ctrl” or “Wet Ctrl”, the digits are flashing, push
[▲▼] key to adjust the Dry/Wet control levels. Push and hold the Up/Down key will speed up
adjusting.

Moisture mode, setup Max irrigation time
Set maximum watering duration to prevent flooding by a fault, such as a broken
hose to avoid wasting water.
1) Push [menu] key to browse into “Max”
time limit set.
2) Digits for hour are flashing,
push [▲▼] to adjust the hour. Then
push [menu] key into minute set.
3) Push [▲▼] to adjust the minute, and
then push [Menu] key to save.

Under Moisture mode, setup irrigation window
Set irrigation window then irrigation will only happen in this time window.
1) Push [menu] key browse into "start" and the
digits will flash.
2) Push [▲▼] to adjust start hour and then push
[menu] key browse into start minute setting.
3) After finished, push [menu] key to save.
4) Finish time and start time are set by same
way.

Under Timer mode, set start time for Timer
For example, If you want to start watering 06:00 every morning for 1 hour, should set
up Start time as 06:00, Interval is 23 hours and duration is 1 hour. please prefer the
following:
1) Push [menu] key browse into “start”, digits would flash which means up/down digits to setup.
2) Push [▲▼] to adjust to 06 hours, push [Menu] and adjust minute to 00, push [Menu]key to save.
Start time

1) Push [menu] key browse into "Interval"
2) Push [▲▼] adjust hour to 23 hours, then push [Menu] into minute and adjust minute
to 00, push [Menu]key to save.
Interval
Under Timer mode, setup timer Interval time