Ancona Valencia Series User manual

© ®
Single Handle Pull-out Bathroom Faucet
STANDARDS
Tools:
PLUMBERS PUTTY FLASHLIGHT BASIN WRENCH
SAFETY GLASSES SCREWDRIVER
PLIERSCHANNELLOCKS ADJUSTABLE WRENCH
HEX-KEY TAPE
Helpful Information
Flow Rate Chart
Valencia
2019-09-16 MAAN4366-1
SEALED-TUBE
Please keep the tools for future use!
ASME A112.18.1/CSA B125.1
ASME A112.18.2/CSA B125.2
LISTED IAPMO/cUPC
Gather the necessary tools as shown below to complete the installation of
this faucet. Some may not be needed depending on the model of faucet you
are installing. Check with your local hardware store on the requirements of
your installation situation.
WARNING:
For easy installation, you will need:
- To read all the installation instructions completely before beginning.
- To read all the warning, attention and maintenance information.
- To purchase the proper supply lines.
Flow diagram
0
1
2
3
10 20 30 40 50 60 70 80
GPM/min
(
Psi
)
(GPM/min)
Connect to water supply lines with either
A 3 8 O D copper tubing ball nose
risers with the coupling nuts or
B 3 8 copper tubing no ball with
supplied tube head interior connector or
C IPS faucet connectors 1 2
C
A . B . C .
Important
Tighten connection with two wrench to prevent damage to
tube body.
Be careful not to bend the stem as this will void the
product warranty

Faucet Installation
3
Installation size map
Step 2: Secure Spout Body in place:
C. Insert black rubber ring into the metal ring.
D. Insert the metal ring in between bottom of
faucet body and sink deck hole.
E. Insert faucet body through sink deck hole.
Step 4: Securing all connections:
H. Connect supply hoses to main water
supply.
I. Ensure all connections are tight to avoid
potential leakage.
7.6 cm
(3 in.)
Faucet Installation
1
Preparation: Turn off water supplies and
drain water lines. Clean installation site
and remove any debris from the area.
Step 1: Connect Supply Hoses:
A. Screw supply hoses and into base of
faucet body.
B. Screw in steel post into base of faucet
body.
2
Step 3: Insert Rubber and Metal washers:
F. Slide black rubber washer and metal washer over
steel post, so that they fit around supply hoses.
G. Insert nut onto steel post.
4
9.8 cm (3.8 in.)
16.5 cm
(6.5 in.)
Ø 4 cm
(1.5 in.)
Ø 2 cm
(0.8 in.)
14.1 cm (5.5 in.)
11.1 cm (4.3 in.)
Ø 3.5 cm (1.3 in.)
2-9/16 in.
Max 4.5 cm

1. Clean it with water and dry it with soft cloth.
2. Clean the product with gentle liquid or glass cleaner.
3. Don't use acid cleaner.
4. Don't clean with abrasive material, abrasive paper or knife.
Cleaning and care
Daily cleaning and care are required in order to keep the product shining and working properly.
A. Move handle into "OFF" position.
B. Turn on water supplies. Check connections for leaks.
C. Remove and let both hot and cold water run for
one minute. This will help clean any debris that might
otherwise clog the system. Replace aerator.
D. Operate handle up and down, in cold and hot positions,
to flush water lines thoroughly.
aerator
Test Faucet Installation
Simply rinse the surface with clear water or
mild liquid detergents if necessary Dry the
faucet with a clean soft cotton cloth Do not
use any cleaning agents containing
acids polish abrasives or harsh cleaners
Maintenance: