Anderic RRTX012 User manual

Anderic® RRTX012 and FD40-H02R Instructions
INSTALLING THE RECEIVER
If replacing the receiver in your fan please follow the
below instructions:
1. Locate the existing receiver unit inside the motor
housing of the fan. For instructions on disassembly,
please refer to the fans’ operating manual, or contact
the manufacturer.
2. Remove the two screws fixing the receiver to the
motor.
3. Unplug the wire harness and remove the receiver.
4. Replace the receiver an reassemble the fan. Follow the
above instructions in reverse order.
SETTING UP THE REMOTE CONTROL
The receiver should already be installed from the factory.
Receiver assembly is not needed.
1. Installing the Battery
Remove the battery cover from the back of the
remote. Insert an “A23 12V” battery (not included);
ensuring the polarity matches with diagram indicated
in the battery compartment. Replace battery cover.
2. Learning/Pairing the remote control (see Figure 1)
The dip switch in the remote control has been set to
“0” to match the receiver in the fan. If there is more
than one fan that uses this same remote control,
changing dip switch setting may be needed.
To change the dip switch setting, slide the switch
inside the battery compartment to “1”, turn off power
to the fan, then turn on the power. Within 30 seconds
of restoring power, tap the “learn” key located inside
battery compartment. If learning is successful, the fan
light will blink three times and turn on.
Note: The fan will run at the highest speed in
corresponding direction per seasonal slide switch.

OPERATING THE REMOTE CONTROL
1. Season slide switch (see Figure 2)
• Slide the switch depending on the direction
you wish the air to flow.
Note: Wait for the fan to stop before
reversing switch.
• In warmer weather, counterclockwise
rotation creates a downward air flow, which
cools the air. Slide switch to the left
indicated by the icon.
• In cooler weather, clockwise rotation
creates an upward air flow, which moves
hot air from the ceiling into the room. Slide
the switch right indicated by the icon.
2. Fan speeds: 6 speeds and natural breeze
• Tap “1”, “2”, “3”, “4”, “5” or “6” key to switch fan to corresponding speed, “1” being the lowest
and “6” being the highest.
• Tap “ ” key to enter Natural breeze mode. Natural breeze mode will simulate a natural breeze,
like being outside. Fan blades will turn at different speeds randomly.
• To exit Natural breeze mode, tap “ ” then one of the numerical settings to shift to relative key
function/speed.
3. Fan On/Off (see Figure 2)
• Fan On/Off controls power to the fan.
• Tapping the “ ” key cycles fan On/Off. The fan will continue with previously set setting when
turning on.
4. Light On/Off/Dimming/Upper and Lower (see Figure 2)
• Tap “ ” key to turn light on/off; press and hold for dimming.
• For fans with Up and Lower Lights only, when applicable:
i. Press the light button for the 1st time: the down light turns on
ii. Press the light button for the 2nd time: the up and down lights both are on
iii. Press the light button for the 3rd time: the up light is on/the down light turns off
iv. Press the light button for the 4th time: the up light turns off
v. Long press the light button to turn the up and down lights on or off at the same time.
5. Walk away light delay (see Figure 2)
• Using this button automatically turns off the light 1 minute after button is pressed.
• Tap “ ” once, light on ceiling fan blinks once to confirm walk-away-light-delay is active, the light
and fan will turn off after 1 minute.
• During walk-away-light-delay mode, press any other key to cancel function.
6. Home shield (see Figure 2)
• Using this button will randomly turn lights on and off to give the illusion that someone is at home.
• Tap “ ”, light on ceiling fan blinks two times to confirm home shield is active. Fan is off and will
cycle through A and B modes as described below:
• A mode: Light randomly turns on for 5-20 minutes.
• B mode: Light is off for 60 minutes.

• During home shield mode, press any other key to cancel function.
7. Sleep timer (see Figure 2)
• Using these buttons will turn the fan off automatically after a 2-hour, 4-hour, 8-hour duration.
• Turn the fan on at the desired speed.
• Tap “2H”, “4H”, or “8H” key. The fan will turn off automatically after desired time has expired.
• During Sleep timer mode, tap “ ” key to exit Sleep timer mode. Tap “ ” or “ ” to also exit
Sleep timer and shift to relative key function.
8. Power off memory (see Figure 2)
• Using this button resumes the settings used on the fan prior to the power being turned off.
• If the fan was in sleep timer mode before the power is turned off, fan will be off when power is
turned back on.
• If the fan is in walk-away-light-delay mode before power is turned Off, both the fan and light will be
off when power is turned back on.
2.
3. WALL BRACKET INSTALLATION
The included wall bracket can be installed to house the
remote control. Remove the small plate preassembled on
the wall bracket and use the screws provided to secure the
wall bracket at desired mounting location. Replace the small
plate.
For product support please go to our website at
www.Anderic.com/RRTX012.
Anderic® is a registered trademark of Dan’s Electronics Etc., Inc.
Customer service regarding the RRTX012 remote control: Phone:
1-855-263-3742
Customer service regarding your fan: Please contact the fan’s
manufacturer or the store the fan was purchased from.