Andrew CommScope Metro Cell Series User manual

3X 120.0°
Figure 1. Metro Cell Antenna. Figure 2. Mounting and Cable Routings Holes on Base.
INSTALLATION INSTRUCTIONSGENERAL INFORMATION
(continued on page 2)
It is the responsibility of qualified personnel to
determine the best method for securely anchoring the
compact antenna including a GPS antenna inside.
base plate of the antenna to the mounting surface.
personnel. Antenna systems should be inspected once a
year by qualified personnel to verify proper installation,
frequency range of the station equipment.
on the bottom of the antenna matches the
• Verify that the frequency range shown on the label
damage.
parts are enclosed and that there is no physical
gloves.
sleeved shirt and rubber
clothing including a long-
and heels. Wear protective
Wear shoes with rubber soles
line can electrocute you.
same. Assume any wire or
lines, and guy wires look the
lines. Power lines, telephone
not use metal ladder.
or thunder is in the area. Do
improper or unsafe installation practices.
windy day or when lightning
Do not install on a wet orDo not install near power
• Examine antenna and hardware to ensure that all
maintenance, and condition of equipment. Commscope
disclaims any liability or responsibility for the results of
NOTICE
The installation, maintenance, or removal of an antenna
requires qualified, experienced personnel. Commscope
installation instructions are written for such installation
The Metro Cell antenna (Figure 1) is a wide band,
Mounting hole 25.0 mm
Recommended hardware is M24
Installation Instructions
•
Metro Cell Family Antennas
Page 1 of 2Bulletin 639843 • Revision A • AUGUST 2015 CommScope Infrastructure Academy offers installation training.

1. Refer to Figures 2, 3 and 4 for mounting and bore-
site alignment. It is recommended that the mounting
holes be marked and made ready in the mounting
Figure 4. Antenna Installation Interface
surface prior to installing the antenna.
Figure 3. Determining Boresite for Each Antenna.
Figure 5. Routing RF Cable and Vertical Alignment
2. Attach the RF cable to the antenna GPS connector
firstly, and then attach the RF cables to the antenna
input connectors, and the 4.3/10.0 DIN connectors to
5-10 Nm (44-88 lbf-in), refer to Figure 5.
(Continued from page 1)
Bulletin 639843 • Revision A • AUGUST 2015 • Page 2 of 2
Notice:
Notice:
Any country: [phone]
Metro Cell Family Antennas Installation Instruction
Customer Service 24 hours
CommScope
each antenna is directed where boresite is desired.
position the antenna unit so that the boresite indicator on
Before mounting the base plate to the mounting surface,
email: [e-mail]
1100 CommScope Place SE P.O. Box 339, Hickory, NC 28603-0339
[phone] [phone]
www.commscope.com/andrew
Avvertenza: CommScope declina eventuali responsabilità derivanti dell’esecuzione di procedure di installazione, ispezione, manutenzione e smontaggio improprie o poco sicure.
@2015 CommScope Bulletin 639843
注意：CommScope 公司申明对于不恰当或不安全的安装、检验、维修或拆卸 操作所导致的后果不负任何义务和责任。
Notice: CommScope disclaims any liability or responsibility for the results of improper or unsafe installation, inspection, maintenance, or removal practices.
Aviso: CommScope no acepta ninguna obligación ni responsabilidad como resultado de prácticas incorrectas o peligrosas de instalación, inspección, mantenimiento o retiro.
Avis : CommScope décline toute responsabilité pour les conséquences de procédures d’installation, d’inspection, d’entretien ou de retrait incorrectes ou dangereuses.
Hinweis: CommScope lehnt jede Haftung oder Verantwortung für Schäden ab, die aufgrund unsachgemäßer Installation, Überprüfung, Wartung oder Demontage auftreten.
Atenção: A CommScope abdica do direito de toda responsabilidade pelos resultados de práticas inadequadas e sem segurança de instalação, inspeção, manutenção ou remoção.
North America: [phone] (toll free)
Torque hardware to 100 Nm (880 lbf-in), hardware not
supplied with antenna.
remove.)
(Do not
Indicator
Boresite
Fastener
Radome
Connection
remove.)
(Do not
Fastener
Connection
Radome
Mounting kit
support base
must include
openingsto
allow routing
of RF cables
(not supplied
with antenna.)
M24 Bolt
Flat Washer
Locting Nut
is truly vertical.
Use inclinometer
to verify antenna
Mounting Kit
Support Base
(not supplied
with antenna)