AndroTec Metor MTR-60R User manual

Instruction Manual
www.androtec.com
Digital Laser Receiver
Model: MTR-60R
Art. 600373
Laser Detection at its Best
V1.1 EN 09.06.2017
www.androtec.com
/links/detectors
Metor

For Your Safety
Safety Instructions
Please read this instruction manual
before using the device for the first
time and comply with it.
Retain this instruction manual for
future reference or for subsequent
owners.
This instruction manual is available
online under:
www.androtec.com/manuals/metor
èOnly authorised and trained personnel are
allowed to repair the device. Only use genuine
spare parts from AndroTec GmbH. This ensures
continuous device safety.
èDo not look directly into the laser beam.
èLaser receiver should not be used in the
vicinity of pacemakers. The magnets produce a
field which can affect the function of the
pacemaker.
èKeep the laser receiver away from data media
and devices that react sensitive to magnetic
force. Exposure to magnets can result in
irreversible data loss.
CAUTION
Prior to the first start-up, it is definitely
necessary to carefully read the Safety
instructions!
Failure to adhere to this instruction manual and the
safety instructions may result in damage to the
device and cause dangerous situations for the
operator and other people.
In case of transport damage please inform your
vendor immediately.
èNoise emission
The a-rated sound pressure level of the acoustic
signal is >80 db (A) at a distance of one meter.
èDo not hold the laser receiver directly to your
ear!
èKeep the laser receiver away from children.
èDo not use the laser receiver in explosive
atmospheres or near flammable liquids, gases
or dust. The device may produce sparks that
can ignite vapours or dust.
èPlease remove the battery if the device is not in
use for a prolonged period of time.
èUse only genuine AndroTec accessories.
When using non-recommended accessories, you
may receive incorrect measuring values.
Laser Detection at its Best
CAUTION
Do not modify the device.
Modifications can cause injuries
and malfunctions.
Page 1
Instruction Manual
Digital Laser Receiver Metor
Model: MTR-60R

Laser Detection at its Best
Page 2
2 3 4 56
6
9
8
10
7
Fig. A
11
14 10
11
12
13
Instruction Manual
Digital Laser Receiver Metor
Model: MTR-60R

Laser Detection at its Best
Page 3
Fig. C
22
21
18
17
18
20
19
Fig. D
Fig. B
15
16
unit
Instruction Manual
Digital Laser Receiver Metor
Model: MTR-60R

Laser Detection at its Best
Page 4
Instruction Manual
Digital Laser Receiver Metor
Model: MTR-60R
1Magnet
2 LED grade indicator (yellow)
3 LED grade indicator (green)
4 LED grade indicator (red)
5 Laser-sensitive area
6 Marking notch
7Clamp
8 Keypad
9 Bubble vial
10 Display
11 Beeper
12 Battery door and latch
13 Type plate with serial number
14 Fixing thread for the clamp
15 On / Off - Beeper volume
16 Deadband resolution - LED On/Off
Device Elements (Fig. A)
Keypad (Fig. B)
Display (Fig. C)
17 Numeric / text display
18 Grade indication arrows
19 On grade indicator
20 Beeper volume
21 Accuracy (Deadband)
22 Low battery
Numeric / text display
Three digits display either the numeric elevation or
simple text messages. Numeric elevation can be
displayed in mm, cm, inch or fractional inch. Resolution
and decimal point will be determined by the units of
measure and the accuracy selected.
Grade indication arrows
Four individual levels of grade information for above
and below grade. Arrow size increases, as distance
from on-grade increases.Arrow bars represent steps of
the selected deadband. Horizontal bar indicates on-
grade.
__________________________________________
Capture height 60 mm
__________________________________________
Numeric readout height 50 mm
__________________________________________
Reception angle ± 45°
__________________________________________
Detectable spectrum 620nm to nm
__________________________________________
Working radius 300m (depending on
laser transmitter)
__________________________________________
Accuracy (Deadband) See table at page 5
__________________________________________
Beeper volumes High (> 100 dBA) /
Low (> 75 dBA) / off
__________________________________________
Automatic shutoff After 30min without key
stroke / laser reception
__________________________________________
Filter against Flash / Sun light / LED /
Fluorescent lamps
__________________________________________
Marking notch 41mm from top edge
__________________________________________
Physical dimensions 135mm x 69mm x 25mm
__________________________________________
Weight without clamp 0,19kg
__________________________________________
Protection class IP 67 (waterproof)
__________________________________________
Power supply 1 x AA
__________________________________________
Battery life > 50h
__________________________________________
Operating temperature -20°C to +50°C
__________________________________________
Storage temperature -40°C to +70°C
__________________________________________
800
The receiver detects the laser beams of rotating laser
transmitters emitting red laser light. Any other use than
the described above shall be deemed to be improper
use.
The user is liable for damage resulting from
improper use.
Technical Specifications
Proper Use

Laser Detection at its Best
Page 5
Setting the numeric elevation display unit:
Press the buttons [15] und [16] at once cycles through
the display units:
>mm: Millimetre
>cm: Centimetre
>in: Inch
>F.in: Fractional Inch
Instruction Manual
Digital Laser Receiver Metor
Model: MTR-60R
Battery (Fig. A/D)
Inserting / changing the battery
!Change the battery if is displayed .
!Open the battery compartment by unlatching the
battery door [12].
!Remove the battery and insert a new one
(observe correct polarity!).
!Dispose of the used battery (see chapter on
environmental protection).
NOTE: Make sure that the device is in
vertical position and that the laser-
sensitive area [5] is not partially covered
during measurement. This can entail
false measuring results.
Operation
Switching the device on / off
To switch on the device, press the On / Off button
[15] . To switch off the device, press and hold the On
/ Off button [15] for more than two seconds until a
confirmation beep sounds.
Adjusting the volume
!Pressing the beeper volume button [15] cycles
trough the following options:
>High: Beeper symbol permanently displayed;
text "Hi" for one second
>Low: Beeper symbol permanently displayed;
text "LOW" for one second
>Off: No Beeper symbol displayed;
text "OFF" for one second
Adjusting the accuracy
!Press accuracy button [16] once to numerically
display current accuracy setting on the LCD. Press
again, while the accuracy is displayed (within one
second), to change the current selection.
!
Fine
Medium
Coarse
1.0
2.0
5.0
0.1
0.2
0.5
0.05
0.1
0.2
1/8
1/4
1/2
mm cm Inch Fract.In. Display
Maintenance and Care
Keep the device always clean, especially the
laser-sensitive area!
!Do not use aggressive cleaning solvents.
!If soiled heavily, the device can be cleaned under
running water.
!Do not use high-pressure cleaner.
!Allow the device to dry completely before storing
it in a closed container. Residual moisture can
result in corrosion of the battery contacts. In this
case our warranty expires.
!In the unlikely event of a failure or defect, have
the appliance examined and repaired by
AndroTec.
!In all your queries and spare part orders, always
quote the 8-digit serial number (see type plate) of
your device.
Environmental Protection
Do not dispose of the device with domes-
tic waste. Have the device disposed of by
an authorised waste management
company or your municipal waste mana-
gement organisation.
Adhere to the applicable regulations. In case of doubt
contact your waste management organisation.
Recycle all packaging material in an environmentally
friendly manner.
Batteries:
Do not dispose of batteries with domestic waste, do
not expose them to fire or water. Collect and recycle
batteries or dispose of them with due care for the
environment.
Activate / deactivate LEDs
Press the LED button [16] for more than two seconds to
change the LED display. If activated, the
measurements are shown by the LEDs in addition to
the display.

Laser Detection at its Best
Page 6
Instruction Manual
Digital Laser Receiver Metor
Model: MTR-60R
Warranty
AndroTec Metor and clamp are warranted to be free of
defects in material and workmanship according to the
statutory warranty regulations.
The user of the product is expected to follow all opera-
ting, maintenance and care instructions. Any evidence
of misuse, alteration, or an attempt to repair products
by unauthorized personnel, or use of parts other than
those provided by AndroTec GmbH automatically voids
the warranty.
AndroTec grants an extended warranty for a period of
three years, if within six weeks from the date of purcha-
se, the warranty registration card is filled out and
returned to AndroTec or the product is registered via
Internet at www.androtec.com. Please make sure that
the registration is filled out properly and on file with
AndroTec.
This warranty period is thirty-six months from the date
the new product is delivered from the dealer to the
purchaser or is put into service by a dealer as a demon-
stration unit or rental unit. Competitor purchased and
tested units are excluded from this warranty.
AndroTec may choose to repair or replace, at its
discretion, any Metor in the event of a failure for any
reason, during the warranty period. In case of a warran-
ty claim, return the product and a proof of purchase to
AndroTec.
AndroTec's liability under this warranty is limited to
repairing or replacing any product returned to its factory
for that purpose. The foregoing states the entire liability
of AndroTec GmbH regarding the purchase and use of
its product and they shall not be held responsible for
any consequential loss or damage of any kind. This
warranty is in lieu of all other warranties, expressed or
implied, and constitutes all of AndroTec GmbH liability
with respect to merchandise sold by it.
Warranty is strictly related to repair or substitution of
defective parts according to AndroTec's discretion. The
warranty does not cover any other damage that may
occur directly or indirectly using defective parts.
AndroTec GmbH
Hauptstraße 186
67714 Waldfischbach-Burgalben
Germany
www.androtec.com
WEEE-Reg.No.: DE37015608
Manufacturer
Declaration of Conformity
We herewith declare that this product conforms with
the following standards and directives:
Standards
·DIN EN 61000-6-1
·DIN EN 61000-6-3
in accordance with the regulations stipulated in the
directives:
EC Directive
·2014/30/EU
·2014/35/EU
Technical Documentation at:
AndroTec GmbH
Mirko Eßling
General Manager
AndroTec GmbH
Waldfischbach-Burgalben, 21.04.2017
© 2017 AndroTec GmbH
Technical changes reserved.
We accept no liability for printing errors.