Angelcare AC1200 User manual

EASY SETUP
Prepare one hardboard
Thickness: 6 mm (1/4’’)
Minimum dimensions:
33 cm (13’’) x 33 cm (13’’)
Maximum dimensions:
equal to the mattress size
IN THE BOX:
NOT INCLUDED:
1 AC AdapterNursery Unit Sensor Pad
Miniature
Philips
Screwdriver
4 AAA
Alkaline
Batteries
IMPORTANT
The hardboard
must be larger
than Sensor Pad
surface area.
STEP 1 – INSTALL APPLICATION
1) Scan QR Code with your smartphone
OR Search for Angelcare baby monitor
in your App Store.
2) Open application and accept
PUSH Notifications.
3) Sign up and create your account.
STEP 2 - INSTALL NURSERY UNIT
1) Plug in your Nursery Unit.
2) Press Nursery Unit Power Button
and wait for activation sound (30 seconds).
3) Rotate Camera Button to top position.
+
4X
E
N
OR
Shortly after signing up, Angelcare
will send you a automatically generated
password by email.
Power light will turn from white to red
and from red to white until a twinkling sound
confirms complete activation.
1.1
1.3
2.1
2.3
2.2
03Bmf2_QuickInstallation_AC1200_EN_11807.indd 1 2013-08-22 9:46 AM

VIA WIRELESS SETUP
1) Select arrow to add camera.
2) Type in your network name and password.
Use your wireless network name and password to
successfully set up your camera(s).
3) QR Code will be displayed on your device screen.
1) Press and hold Neck Button until
you hear a twinkling sound (3 seconds).
2) Place Nursery Unit and device
approximately 6 inch apart until you hear
a twinkling sound. (Align QR code
with camera lens)
3) Wait for 30 seconds for camera
to connect. Another twinkling sound
will confirm camera connection:
Success Message will appear
on your screen.
1) Edit your camera name.
2) Select your camera.
3) Modify your settings.
STEP 3 - SET UP CAMERA
STEP 4 - CONNECT
STEP 5 - EXPLORE THE APPLICATION
Power light will turn red during
the connecting waiting period.
3.1
5.1
4.3
3.2
5.2
1
4.1 4.2 6 in
5.3
Application
Settings
Camera
Settings
NOTE:
If the connection is not
successful, you will hear a
failed sound. Please try to
connect again.
VIA ACCESS POINT SETUP (No Internet connection needed)
1) Set camera to AP mode (switch underneath camera)
2) Select Angelcare camera via your WiFi
settings device using password: 12345678
3) Restart the app (if it does not work immediately)
OR (IF YOU DON’T HAVE AN INTERNET CONNECTION)
03Bmf2_QuickInstallation_AC1200_EN_11807.indd 2 2013-08-22 9:46 AM

FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/ TV technician for help.
CAUTION:
Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to
operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used
for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must
not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must
be provide with antenna installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
Canada, Industry Canada (IC) Notices
This Class B digital apparatus complies with Canadian ICES-003 and RSS-210.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
Canada, avis d'Industry Canada (IC)
Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210.
Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer
d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent
affecter son fonctionnement.
Radio Frequency (RF) Exposure Information
The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure
limits. The Wireless Device should be used in such a manner such that the potential for human contact during
normal operation is minimized.
This device has also been evaluated and shown compliant with the IC RF Exposure limits under mobile exposure
conditions. (antennas are greater than 20cm from a person's body).
Informations concernant l'exposition aux fréquences radio (RF)
La puissance de sortie émise par l’appareil de sans fil est inférieure à la limite d'exposition aux fréquences radio
d'Industry Canada (IC). Utilisez l’appareil de sans fil de façon à minimiser les contacts humains lors du
fonctionnement normal.
Ce périphérique a également été évalué et démontré conforme aux limites d'exposition aux RF d'IC dans des
conditions d'exposition àdes appareils mobiles (les antennes se situent à moins de 20 cm du corps d'une
personne).

Spec:
1. Dimension: 240*240*10mm
2. 2M length cable with 3.5mm pin
3. Piezoelectricity to detect vital signs
Function:
1. Connect to Babycam by 3.5mm pin.
2. Baby lies down on the sensor pad, once baby without vital signs, pad will send signal to Babycam for alarm.
Sensor Pad Introduction