Anolis ArcPad Zoom 48MC User manual

Version 1.
1

ArcPad Zoom 48MC
2
Table of contents
1. Safety instructions ...................................................................................................................................................... 3
2. Fixture exterior vie ................................................................................................................................................... 5
3. Installation .................................................................................................................................................................. 5
3.1 Mounting the fixture ............................................................................................................................................ 5
3.2 Connection to the mains ...................................................................................................................................... 6
3.3 Wireless DMX operation ....................................................................................................................................... 7
4. ArcPad Zoom 48MC (RGBW) - DMX protocol ............................................................................................................ 8
5. Control menu map (RGBW version) ......................................................................................................................... 10
6. Control menu ............................................................................................................................................................ 13
6.1 Addressing (DMXA) ............................................................................................................................................. 13
6.2 Fixture information (Info) ................................................................................................................................... 13
6.3 Personality (Pers) ................................................................................................................................................ 14
6.4 Manual Control (Manual) ................................................................................................................................... 14
6.5 Test program (Test Prg) ...................................................................................................................................... 14
6.6 Stand-alone (St Alone) ........................................................................................................................................ 15
6.7 Reset ................................................................................................................................................................... 15
6.8 Special functions (Special) .................................................................................................................................. 15
7. RDM .......................................................................................................................................................................... 17
8. Technical specifications ............................................................................................................................................ 18
9. Cleaning and maintenance ....................................................................................................................................... 21
9.1 Replacing a fuse .................................................................................................................................................. 21

ArcPad Zoom 48MC
3
FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY
BEFORE POWERING OR INSTALLING YOUR ArcPad Zoom 48MC
Save it for future reference.
This device has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a
safe operation, it is absolutely necessary for the user to follo the safety instructions and arning notes ritten in
this manual.
The manufacturer ill not accept liability for any resulting damages caused by the non-observance of this manual
or any unauthorized modification to the device.
Please consider that damages caused by manual modifications to the device are not subject to arranty.
This device is for professional use only. It is not for household use.
1. Safety instructions
DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT
Make sure that the available voltage is not higher than stated on the rear side of the fixture.
This fixture should be operated only from the type of po er source indicated on the marking label. If you are not
sure of the type of po er supplied, consult your authorized distributor or local po er company.
Al ays disconnect the fixture from AC po er before cleaning, removing or installing the fuses, or any part.
Do not overload supply line as this can result in fire or electric shock.
Make sure that the po er/data cable is never crimped or damaged by sharp edges. Check the fixture and the
po er/data cable from time to time.
Do not install the unit near naked flames.
Refer servicing to qualified service personnel.
This fixture falls under protection class I. Therefore this fixture has to be connected to a mains socket outlet with
a protective earthing connection.
Do not connect this fixture to a dimmer pack.
Warning Risk Group 2 LED product according to EN 62471 .
LED light emission. Risk of eye injury.
Do not look straight at the fixture´s LEDs during operation. The intense light beam may damage your eyes.
Keep compustible materials at least 0.2 m a ay from the fixture.
If the fixture has been exposed to drastic temperature fluctuation (e.g. after transportation), do not s itch it on
immediately. The arising condensation ater might damage your device. Leave the device s itched off until it has
reached room temperature.
Avoid brute force hen installing or operating the fixture.

ArcPad Zoom 48MC
4
When choosing the installation spot, please make sure that the fixture is not exposed to extreme heat or dust.
Avoid using the unit in locations subject to possible impacts.
Only operate the fixture after having checked that the housing is firmly closed and all scre s are tightly fastened.
Make sure that the area belo the installation place is blocked hen rigging, derigging or servicing the fixture.
Do not block the front glass cover ith any object hen the fixture is under operation.
The fixture body never must be covered ith cloth or other materials.
The fixture becomes very hot during operation. Allo the fixture to cool approximately 30 minutes prior to
manipulate ith it.
Operate the fixture only after having familiarized ith its functions. Do not permit operation by persons not
qualified for operating the fixture. Most damages are the result of unprofessional operation!
Do not attempt to dismantle or modify the unit.
Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons!
Please use the original packaging if the fixture is to be transported.
If this device ill be operated in any ay different to the one described in this manual, the product may suffer
damages and the guarantee becomes void. Furthermore, any other operation may lead to dangers like short-
circuit, burns, electric shock etc.

ArcPad Zoom 48MC
5
2. Fixture exterior view
3. Installation
3.1 Mounting the fixture
The ArcPad Zoom 48MC can be arranged in any position orientation ithout altering its operation characteristics.
The LED module can be tilted to desired position by means of the tilt lock. Use an Allen key 6 to adjust desired tilt
position.
Three slots in the mounting bracket serve for mounting on the non-flammable flat surface.
Dimensions in mm
1.
Head
2. LED zone
3. Tilt locks
4. Bracket
5. Control board ith cover
6. Po er/DMX input

ArcPad Zoom 48MC
6
Ensure that the structure to which you are attaching
the fixture is secure.
Caution: Overhead installation requires experience. Fixtures may cause severe injuries hen crashing do n! If you
have doubts concerning the safety of a possible installation, do not install the device and consult installation ith
an expert.
3.2 Connection to the mains
Fixtures must be installed by a qualified electrician in accordance with all national
and local electrical and construction codes and regulations.
This device falls under class one and must be grounded!
The ArcPad Zoom 48 MC is equiped ith ith a 5-cored po er/data cable. The 3 cores serve for the po er supply
and next 2 shielded cores are intended for DMX connection as sho n the table.
Core
Connection
Core
Connection
Black
Live
Red
Data +
B
lue
Neutral
White
Data
-
Yello /Green
Shielding
0
The po er/data cable is connected to a junction box as sho n on the picture belo .
Connect the junction box acording to the tables belo
Power connection
L
EU
Braun
Blue
Green/yello
US
Black
White
Green

ArcPad Zoom 48MC
7
DMX connection
+
0
-
Data +
Data ground(shielding)
Data
-
There is an example of possible ArcPad Zoom 48MC connection
The junction box allo s to connect several fixtures in a daisy chain of the po er/data cable. Use the 3 x 1.5mm
2
po er cable to connect the first junction box ith the mains and the po er/data cable for connecting fixtures
each other. Do not overload the supply line and the connecting leads.
The max. number of connected fixtures in a daisy chain depends on input voltage:
13 fixtures at po er supply= 230V (for po er cable 3 x 1.5mm
2
)
6 fixtures at po er supply= 120V (for po er cable 3 x 1.5mm
2
)
You have to take into account the the length of po er/data cable, circuit breaker etc. at projecting of the fixtures
installation.
3.3 ireless DMX operation
The ireless version of the ArcPad Zoom 48MC ( ArcPad Zoom 48MC/W) is equipped ith the Lumen Radio CRMX
module and antenna for receiving DMX signal. CRMX module operates on the 2.4 GHz band.
1. Select ireless DMX input from the menu PErS (PErs-->dMX In.-->Wireless).
2. To link the fixture ith DMX transmitter.
The fixture can be only linked ith the transmitter by running the link procedure at DMX transmitter .
After linking , the level of DMX signal ( 0-100 %) is displayed in the menu
item “Stat“ (Special -->Wireless--> Stat).
3. To unlink the fixture from DMX transmitter.
The fixture can be unlinked from receiver via the menu item “Unlink“ (Special-->Wireless-->Unlink).

ArcPad Zoom 48MC
8
4. ArcPad Zoom 48MC (RGB ) - DMX protocol
Version 1.1
Mode 1 - Standard 16 bit, Mode 2 - Reduced 8 bit
Mode/Channel
DMX
Value
Function
Type of
control
1 2
1 1
0-29
30-39
40-49
50-59
60-69
70-89
90-99
100-109
110-179
180-189
190-255
Special
functions
Reserved
To activate following functions , stop in DMX value
for at least 3 sec. and shutter must be closed at least 3
sec. (Shutter channel 1 /9 must be at range of 0-31 DMX).
Corresponding menu items are temporily overrided.
RGBW colour mixing mode
CMY colour mixing mode
Colour calibration mode On
Colour calibration mode Off
Reserved
Dimmer curve: linear
Dimmer curve: square la
Reserved
To activate zoom reset function, stop in DMX value for at
least 3 sec.
Zoom reset
Reserved
step
step
step
step
step
step
step
2 2
0-255
Red (Cyan) coarse
Red LEDs saturation control (0-100%)
proportional
3 -
0-255
Red (Cyan) fine
Red LEDs saturation fine control min.—>max.
proportional
4 3
0-255
Green (Magenta) coarse
Green LEDs saturation control (0-100%)
proportional
5 -
0-255
Green (Magenta) fine
Green LEDs saturation fine control min.—>max.
proportional
6 4
0-255
Blue (Yellow) coarse
Blue LEDs saturation control (0-100%)
proportional
7 -
0-255
Blue (Yellow) fine
Blue LEDs saturation fine control min.—>max.
proportional
8 5
0-255
White coarse (RGBW mode only)
White LEDs saturation control (0-100%)
proportional
9 -
0-255
White fine (RGBW mode only)
White LEDs saturation fine control min.—>max.
proportional
10 6
0
1-255
CT0
No function
Colour temperature correction
step
proportional
11 7
0
Virtual colour wheel
No function
step

ArcPad Zoom 48MC
9
1
-
2
3
4-5
6
7-9
10-12
13-15
16
17-55
56
57 - 95
96
97 – 134
135
136 - 174
175
176 -214
215
216 - 246
247
248-251
252-255
White
2700 K
White 2700 K (tungsten emulation)*
White 3200 K
White 3200 K (tungsten emulation)*
White 4200 K
White 5600 K
White 8000 K
Blue (Blue=full, Red+Green+White=0)
Red=0, Greenup,Blue =full, White=0
Light Blue (Red=0, Green=full, Blue =full, hite=0)
Red=0, Green=full, Bluedo n, White=0
Green (Red=0, Green=full, Blue =0, White=0)
Redup, Green=full, Blue=0, White=0
Yellow (Red=full, Green=full, Blue=0,White=0)
Red=full, Greendo n, Blue=0, White=0
Red(Red=full, Green=0, Blue=0, White=0)
Red=full, Green=0, Blueup, White=0
Magenta (Red=full, Green=0, Blue=full, White=0)
Reddo n, Green=0, Blue=full, White=0
Blue (Red=0, Green=0, Blue=full, White=0)
Rainbo effect ( ith fade time) from min.->max. s peed
Rainbo effect( ithout fade time)from min .-> max. s peed
step
step
step
step
step
step
step
step
proportional
step
proportional
step
proportional
step
proportional
step
proportional
step
proportional
step
proportional
proportional
12 8
0-255
Zoom
coarse
Zoom from min. to max. beam angle
proportional
13 -
0-255
Zoom fine
Fine zooming from min.—>max.
proportional
14 9
0-31
32-63
64-95
96-127
128-143
144-159
160-191
192-223
224-255
Shutter/ Strobe
Shutter closed
Shutter open
Strobe-effect from slo to fast
Shutter open
Opening pulses in sequences slo --> fast
Closing pulses in sequences fast --> slo
Shutter open
Random strobe-effects from slo to fast
Shutter open
step
step
proportional
step
proportional
proportional
step
proportional
step
15 10
0 - 255
Dimmer coarse
Dimmer intensity from 0% to 100%
proportional
16 -
0 - 255
Dimmer fine
Dimmer intensity from min.—>max.
proportional
*Halogen lamp effect during dimming

ArcPad Zoom 48MC
10
5. Control menu map (RGB version)
Default settings=Bold print
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
DMXA
Set DMX
address
001
-
255
DMX Pres
Mode 1
Mode 2
Info
POn Time
Total
Reset
DMX In
Po r
0
-
255
:
Dimm
F
0
-
255
Temp
Current
High Res
Highest
S
Ver
IC
-
1
IC
-
2
IC
-
3
WL
Pers
DMX Pres
Mode 1
Mode 2
RGB Cnt
Active, Deactive
DMX In
Wired
Wireless
Display
Turn
On/Off T
On, Off
Contrast
0
-
100%
Backlight
0
-
100%
C Cal M
On
, Off

ArcPad Zoom 48MC
11
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
C Mix M
RGBW
, CMY
Dimmer
Sq
L
Linear
Temp Uni
°C
, °F
I Ef Pos
Po r
:
Dimm
F
Store
Defaults
Manual
Po r
:
Dimm F
Test Prg
Sta Alone
Auto Run
Off
Test
User
Pr Play
Test Prg
User Prg
Pr Edit
Step 1
Prg End
:
Po er
Step 4
0
:
Copy
Reset
Special
RDM
UID
RDM L
RDM H

ArcPad Zoom 48MC
12
Level 1
Level 2
Level 3
Level 4
Level 5
Level 6
Level 7
Wireless
Stat
Unlink
Adjust
DMX Val
Po r
0
-
255
:
Dimm
F
0
-
255
Calib
R
ed
G
reen
B
lue
W
hit
Store
Load d
.
C
S Upd
On, Off

ArcPad Zoom 48MC
13
6. Control menu
The ArcPad Zoom 48MC is equipped ith 2-line LCD display hich allo s to set the fixture´s behaviour according
to your needs, obtain information on its operation, control various range of effects and lastly program it, if it has to
be used in a stand-alone mode.
Control board:
The four control buttons on the front have the follo ing functions:
- ESCAPE button-leaves menu ithout saving changes.
- E TER button- enters menu, confirms adjusted values and leaves menu.
- UP and - DOW buttons - move bet een menu items on the same level, sets values.
After s itching the fixture on, display sho s current DMX address .
6.1 Addressing (DMXA)
Set DMX address- Use this menu item to set the DMX start address of the fixture, hich is defined as the first
channel from hich the fixture ill respond to the DMX controller.
Please, be sure that you do not have any overlapping channels in order to control each ArcPad Zoom 48MC
correctly and independently from any other fixture on the DMX data link.
If there is no data received at the DMX input, the display ill start to flash "0001” ith actually stored DMX
address.
DMX Pres - DMX preset. Use the menu to select desired channel mode.
Mode 1 - 16 control channels
Mode 2 - 10 control channels
6.2 Fixture information (Info)
POn Time - Power on time. Select this menu to read the number of fixture operation hours.
Total - The item sho s the total number of the operation hours since
the ArcPad Zoom 48MC has been fabricated.
Reset - The item sho s the number of the operation hours that the
ArcPad Zoom 48MC has been po ered on since the counter as last reset.
In order to reset this counter to 0, press and hold both [UP] and [DOWN] buttons and the
[Enter] button at the same time.
DMX In - DMX readout. The menu is used to read DMX values of each channel received by the fixture.
Temp - Temperature. The menu sho s temperature in the moving LED head.
Current - A current temperature of the moving LED head.
Highest - A maximum temperature of the moving LED head since the fixture has
been fabricated.
High Res - A maximum temperature of the the moving LED head since the counter
as last reset.

ArcPad Zoom 48MC
14
In order to reset this counter, press and hold both [UP] and [DOWN] buttons and the
[Enter] button at the same time.
Sw Ver - Software versions. Select this item to read version of soft are in fixture processors (IC-1, IC-2, IC-3, WL).
6.3 Personality (Pers)
DMX Pres - DMX preset. Use the menu to select desired channel mode.
Mode 1 - 16 control channels
Mode 2 - 10 control channels
RGB Cnt ---RGB counting. If this function is active, the hite channel (channel 4) uses red, green and blue chanels
in proportional relation to ensure max. light output in a hite colour ( if hite channel =full, also red, green and
blue channels are full).
DMX In - DMX input. Use the menu to select mode of receiving DMX signal.
Wired - DMX signal is received by means of the standard DMX cable.
Wireless - DMX signal is received by means of the inbuilt ireless module (if the module is installed).
Display - Display adjusting. This menu allo s you to adjust the display behaviour.
Turn - This function rotates menu 180 degrees from current orientation.
On/Off T - This function allo s you to keep the display permanent on or turn it off t o
minutes after last pressing any button on the control panel.
Contrast- Use this function to adjust contrast of the display (0-100%).
Backlight- Use this function to adjust backlight of the display (0-100%).
C Cal M - Colour calibration mode. If the functin is on, the hite output (2700K-8000K) from the fixture (and also
mixed colours) is more uniform.
C Mix M - Colour mixing mode. This item allo s s itching into RGBW or CMY mode. In the CMY mode, the
hite(8bit) and hite (16) bit channels are not active.
Dimer C – Dimmer curve. This menu item allo s to set linear (Linear) or square la (SqL) dimmer curve.
Temp Uni - Temperature unit. Use the menu item to change temperature unit from °C to °F.
I Ef Pos - Init effect positions. Use the menu to set all effects to the desired positions at hich they ill stay after
s itching the fixture on ithout DMX signal connected.
Defaults - The menu item allo s to set all fixture parameters to the default (factory) values.
6.4 Manual Control (Manual)
Use the menu to control all fixture channels by means of the control panel. Displayed menu items depend on
selected DMX mode.
6.5 Test program (Test Prg)
Use this menu item to run a special demo-test sequences ithout an external controller, hich ill sho you some
possibilities of using ArcPad Zoom 48MC.

ArcPad Zoom 48MC
15
6.6 Stand-alone (St Alone)
Auto Run - Presetting playback. This function allo s you to select the program hich ill be played in the stand-
alone mode after s itching the fixture on. Selected program ill be played continuously in a loop.
Off - The option disables „Auto Run” function.
Test - The option ill start built-in test program.
User - The option ill start user-created program
Pr Play - Playing program. Select this menu to run a user-created program in a loop.
Test Prg - The option runs built-in test program.
User Prg - The option runs user-created program
Select the program you ish and press [ENTER]. The selected program starts running. By Pressing [ENTER] again,
program pauses running.
Pr Edit - Editing program. Select this menu to edit or create the program. The ArcPad Zoom 48MC has one built-in
program and one user-editable program up to 40 steps. Each program step has a step time during hich effects
last in the current step.
To edit program:
Procedure:
1. Press [UP] or [DOWN] to select the menu "Pr Edit" and press [ENTER].
2. Press [UP] or [DOWN] to select the desired program step and press [ENTER] button.
3. Press [UP] or [DOWN] to select the desired item and press [ENTER] button. No you can edit by [UP] or [DOWN]
buttons the DMX value (0-255) for selected item:
Prg End. a total number of the program steps (value 1-40). This value you should be set before
starting of programming (e.g. if you ant to create program ith the 10 steps, set Prg End=10)
Po r a po er/special functions
R L A red LEDs (all pixels)
G L A green LEDs (all pixels)
B L A blue LEDs (all pixels)
W L A hite LEDs (all pixels)
CTO a colour temperature correction
Vir C a virtual colour
Zoom a zoom movement
Stro a strobe/shutter
Dimm a dimmer
S.Tm a step time (0-25.5 sec)
COPY copying the current prog. step to the next prog. step
4. Press [ENTER] button to confirm adjusted value .
5. Press [ESCAPE] button, select next prog. step, press [ENTER] button and repeat steps 3 - 5).
6.7 Reset
This option resets zoom system of the fixture.
6.8 Special functions (Special)
RDM UID
RDM L - This menu item sho s the first part of the RDM identification code.

ArcPad Zoom 48MC
16
RDM H - This menu item sho s the second part of the RDM identification code.
Wireless - Wireless DMX status. The menu serves for reading of the ireless operation status.
Stat - Wireless DMX information. The menu item sho s level of received signal in %.
UnLink - Wireless DMX unlink. The item serves for unlinking the fixture from transmitter.
Adjust - Adjustment. The menu allo s the fine adjustment of colours.
DMX Val- DMX values. Use the menu to set DMX values of fixture´s channels.
Calib – A calibration of hite colour 5600K.
Load d.C. – Loading a default calibration.
Sw Upd - Software update. The menu item allo s you to update soft are in the fixture via either serial or USB
port of PC.
The follo ing are required in order to update soft are:
- PC running Windo s 95/98/2000/XP/7/8 or Linux
- DMX Soft are Uploader
- Flash cable RS232/DMX No.13050624 (if you ant to use a serial port of PC)
- Robe Universal Interface (if you ant to use an USB port of PC)
Note 1: Soft are update should execute a qualified person. If you lack qualification, do not attempt the update
yourself and ask for help your Anolis distributor.
Note 2: DMX address, user program and all items in the menu "Pers" ill be set to their default (factory) values.
To update software in the fixture:
I. Installation of the DMX Soft are Uploader.
1. DMX Soft are Uploader program is available from the Anolis eb site at WWW.anolis.cz.
2. Make a ne folder ( e.g. Anolis_Uploader) on your hard disk and do nload the soft are to it.
3. Unpack the program to the folder.
II.Fixture soft are updating.
1.Determine hich of your ports is available on your PC and connect it:
- ith the DMX input of the fixture if you using the flash cable RS232/DMX
- ith the DMX output of the Robe Universal Interface if you using the USB cable.
Disconnect the fixture from the other fixtures in a DMX chain. Turn both the computer and
the fixture on. Make sure the lamp is s itched off (only if the fixture involves a lamp).
2. S itch the fixture to the updating mode by selecting the "SW Upd " item and press [ENTER].
Note: If you do not ant to continue in soft are update, you have to s itch off and on the fixture
to escape from this menu.
We recommend to cancel all running programs before starting the Soft are Uploader.
3. Run the Soft are Uploader program. Select desired COM and then click on the Connect button.
(Select COM if the serial port is used or Robe Universal Interface if the USB port is used).
If the connection is OK, click on the “Start Uploading button“ to start uploading. It ill take several
minutes to perform soft are update.
If the option "Incremental Update" is not checked, all processors ill be updated (including
processors ith the same soft are version).
If you ish to update only later versions of processors, check the “Incremental Update box“.
Avoid interrupting the process. Update status is being displayed in the Info Box indo .
When the update is finished, the line ith the text “The fixture is successfully updated“ ill appear in
this indo and the fixture ill reset ith the ne soft are.
Note: In the case of an interruption of the upload process (e.g. po er cut), the fixture keeps the updating mode
and you have to repeat the soft are update again.

ArcPad Zoom 48MC
17
7. RDM
This fixture is ready for RDM operation. RDM (Remote Device Management) is a bi-directional communications
protocol for use in DMX512 control systems, it is the ne open standard for DMX512 device configuration and
status monitoring.
The RDM protocol allo s data packets to be inserted into a DMX512 data stream ithout adversely affecting
existing non-RDM equipment. By using a special „Start Code,“ and by complying ith the timing specifications for
DMX512, the RDM protocol allo s a console or dedicated RDM controller to send commands to and receive
messages from specific moving lights.
RDM allo s explicit commands to be sent to a device and responses to be received from it.
The list of commands for the fixture is the follo ing.
Parameter ID Discovery command SET command GET command
DISC_UNIQUE_BRANCH *
DISC_MUTE *
DISC_UN_MUTE *
DEVICE_INFO *
SUPPORTED_PARAMETERS *
SOFTWARE_VERSION_LABEL *
DMX_START_ADDRESS * *
IDENTIFY_DEVICE * *
DEVICE_MODEL_DESCRIPTION *
MANUFACTURER_LABEL *
DEVICE_LABEL
*
*
SENSOR_DEFINITION
*
SENSOR_VALUE
*
DISPLAY_LEVEL
*
*
DEVICE_RESET
*
DMX_PERSONALITY
*
*
DMX_PERSONALITY_DESCRIPTION
*
STATUS_MESSAGES
*
STATUS_ID_DESCRIPTION
*
DEVICE_HOURS
*
Please, see the Robe Universal Interface user manual for detail description of RDM operation.

ArcPad Zoom 48MC
18
8. Technical specifications
Power supply
• Electronic auto-ranging
• Input voltage: 100 - 277V AC, 50-60 Hz
• Max. po er consumption: 150W@230V (po er factor=0,94)
Optic & Effects
• Light source: 12 x 15W LED multi-chip
• Zoom range: 8° - 44°( at ½ beamu)
• RGBW or CMY colour mixing
• Built-in colour macros
• Adjustable strobe sequences
•Typical Lumen maintenance: 70% @ 60.000 hours
Control
• Setting & Addressing: t o-ro LCD display & 4 control buttons
• Control: USITT DMX 512 (RDM support)
• DMX protocol modes: 2 (16,10 control channels)
• Operations modes: DMX, Stand-alone
• Manual control of all effects via control panel
• One editable program, up to 40 steps
Wireless DMX/RDM module (only for ArcPad Zoom 48MC/W)
• Compliance ith USITT DMX-512 (1986 & 1990) and 512-A
• Full DMX fidelity and frame integrity
• Auto sensing of DMX frame rate and frame size
• <5ms DMX latency
• Operational frequency range of 2402-2480 MHz
• Producer: LumenRadio
Strobe
• Strobe effect ith variable speed (max. 20 flashes per second)
• Pre-programmed random strobe pulse-effects
Dimmer
• Smooth 16-bit dimming from 0 - 100 %
Connection
• Data/po er cable: Li9Y11Y 3xAWG16+2xAVG24 shielded and jacketed
• junction box
Mounting
• Via mounting bracket
Protection factor
• IP 67
Impact resistance
• IK 10

ArcPad Zoom 48MC
19
Temperatures
• Ambient temperature range: -20°C/+40° C
• Maximum housing temperature: 70° C
Total heat dissipation
• 440 BTU/h (calculated)
Weight
• 11.6 kg (fixture)
• 1.5 kg (floor stand)
Dimensions (mm)

ArcPad Zoom 48MC
20
Junction box
Included items
• 1 x ArcPad Zoom 48MC
• 1 x Junction box (P/N 99714080)
• 1 x Data/po er cable
• 1 x User manual
Optional accessories
• Floor stand for ArcPad Zoom 48MC (P/N 10980235)