Anritsu Rubidium MG36271A User manual

Operation Manual
Rubidium™ MG362x1A Series
Low-Noise RF/Microwave Signal
Generators
MG36221A, 9 kHz to 20.0 GHz
MG36241A, 9 kHz to 43.5 GHz
MG36271A, 9 kHz to 70.0 GHz
Anritsu Company
490 Jarvis Drive
Morgan Hill, CA 95037-2809
USA
P/N: 10370-10383
Revision: E
Printed: June 2023
Copyright 2023 Anritsu Company

1-2 PN: 10370-10383 Rev. E MG362x1A OM
Unauthorized Use or Disclosure
Anritsu Company has prepared the product user documentation for use by Anritsu Company personnel and
customers as a guide for the proper installation, operation, and maintenance of Anritsu Company equipment and
software programs. The drawings, specifications, and information contained therein are the property of Anritsu
Company, and any unauthorized use of these drawings, specifications, and information is prohibited; they shall not be
reproduced, copied, or used in whole or in part as the basis for manufacture or sale of the equipment or software
programs without the prior written consent of Anritsu Company.
Export Management
The Anritsu products identified herein and their respective manuals may require an Export License or approval by
the government of the product country of origin for re-export from your country. Before you export these products or
any of their manuals, please contact Anritsu Company to confirm whether or not these items are export-controlled.
When disposing of export-controlled items, the products and manuals must be broken or shredded to such a degree
that they cannot be unlawfully used for military purposes.
Contacting Anritsu
To contact Anritsu, visit the following URL and select the services in your region:
http://www.anritsu.com/contact-us

MG362x1A OM PN: 10370-10383 Rev. E 1-1
Table of Contents
Chapter 1 — General Information
1-1 About this Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-3 Additional Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
1-4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1-5 Instrument Integrity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Antivirus Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
1-6 ESD Caution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-7 Instrument Care and Preventive Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Cleaning the Fan Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Connector Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Power Output. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-8 Unpacking the Product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-9 Operating Environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
1-10 Typographic Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1-11 Preparation for Storage/Shipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Preparation for Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Preparation for Shipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
1-12 Contacting Anritsu for Sales and Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Instrument Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Chapter 2 — Instrument Overview
2-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
2-2 Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Menu Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Rotary Knob. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Cursor Control Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Numeric Keypad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
RF Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
2-3 Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Rear Panel BNCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
2-4 Installation and Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
2-5 Powering On the MG362x1A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Standby Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Warm-up Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
2-6 Common GUI Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
2-7 GUI Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
2-8 Title Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
2-9 Menu Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
2-10 Status Area. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13

1-2 PN: 10370-10383 Rev. E MG362x1A OM
Table of Contents (Continued)
2-11 Entering Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Opening a Parameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Cursor Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Text Entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-18
2-12 System Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20
SYSTEM INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
INSTRUMENT Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-21
SOFTWARE Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-22
CONNECTIVITY Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-23
2-13 SETTINGS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24
DISPLAY Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
SOUND Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-25
ETHERNET Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-26
Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-27
2-14 Connecting to the MG362x1A or Localhost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
Working with the Localhost . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
Measurement Setup Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
2-15 REMOTE Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
GPIB Interface Connection and Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-29
SCREENSHOT Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-31
Previewing Screenshots . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-32
DATE TIME Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-33
OPTIONS Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-34
RESET Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-35
Resetting to Default Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-36
2-16 FILES Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
File Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
File Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
File Management Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37
2-17 DIAGNOSTICS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
EVENT LOG Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-38
SELF TEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-39
SERVICE Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-41
TOOLS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-42
Chapter 3 — Instrument Operation
3-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3-2 Power-on Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3-3 Standby Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3-4 Self Testing the MG362x1A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3-5 Resetting to Default Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3-6 CW Frequency Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
FREQUENCY Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
FREQUENCY Menu (Option 36) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
FREQUENCY PRESETS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6

MG362x1A OM PN: 10370-10383 Rev. E 1-3
Table of Contents (Continued)
3-7 Frequency Step Sweep Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
SWEEP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
SUMMARY Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
Step Sweep SETUP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Editing the Current Start/Stop Frequencies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Setting the Step Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Number of Points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Setting DWELL TIME . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Setting SWEEP DIRECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
Setting PRESET SWEEP RANGES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-11
RANGE Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
Setting SWEEP TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-12
3-8 Starting a Step Sweep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
TRIGGER Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Sweep TRIGGER TYPES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Initiate Step Sweep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
3-9 LIST Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
SWEEP LIST Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-16
LIST TRIGGER Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-18
LIST - LIST Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Copy to the LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
3-10 Power Level Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
LEVEL Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-21
LEVEL SETUP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-25
LEVEL PRESETS Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Setting Fixed Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
Setting a Preset Power Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-29
LEVEL OFFSET Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
Edit the Offset Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
3-11 Power Level Sweep Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
LEVEL SWEEP Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
Setting CW Power Sweep, Step Size, and Dwell Time . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
Triggering a CW Power Sweep . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
RANGE Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36
Setting a Power Level Sweep Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-36
Setting SWEEP TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-37
3-12 Setting the ALC Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38
ALC Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38
ALC Level Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-38
3-13 Step Attenuator (Option 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40
ATTENUATOR Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-40
Decoupling the Attenuator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-41
POWER SEARCH Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-43
3-14 Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-44

1-4 PN: 10370-10383 Rev. E MG362x1A OM
Table of Contents (Continued)
3-15 Amplitude Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-44
Setting AM SOURCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-44
Amplitude Modulation Set to Internal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-45
Amplitude Modulation Set to External . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-48
3-16 Frequency Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-50
Setting FM SOURCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-50
Frequency Modulation Set to Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-51
Frequency Modulation Set to External. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-54
3-17 Phase Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-56
PHASE Modulation Set to Internal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-56
PHASE Modulation Set to External . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-59
3-18 Pulse Modulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-60
Setting Pulse SOURCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-60
PULSE Modulation Set to Internal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-61
Setting Period and (PRF) FREQUENCY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-62
Pulse Width-Delay Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-62
PULSE Modulation Set to External . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-66
3-19 Saving/Recalling Instrument Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-67
Saving Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-67
Erasing Stored Setups. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-68
3-20 Reference CALIBRATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-69
100 MHz Calibration (Standard Reference). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-70
10 MHz Calibration (Option 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-70
100 MHz Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-71
10 MHz Calibration With Option 66 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-73
RUBIDIUM Menu (Option 56) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-74
GNSS Menu (Option 66) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-75
3-21 Reference Status Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-76
Reference Oscillator Current Source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-76
Reference Oscillator Lock Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-76
Reference Oscillator 100 MHz Lock Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-76
Reference Oscillator GPS Lock Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-77
Reference Oscillator Rubidium Lock Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-77
Config Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-78
INCREMENT Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-79
Increment Size. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-79
RESET Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-80
Chapter 4 — Operation Verification
4-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4-2 Test Records. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4-3 Initial MG362x1A Checkout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Power On. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Warm-up Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Self Test. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4-4 Presetting the MG362x1A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

MG362x1A OM PN: 10370-10383 Rev. E 1-5
Table of Contents (Continued)
4-5 Frequency Synthesis Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
4-6 Level Accuracy and Flatness Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5
4-7 Accuracy Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
4-8 Flatness Test Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Appendix A — Software Installation
PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
A-2 FILE (File Management) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Appendix B — Updating Firmware
B-1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
B-2 Updating Firmware on the MG362x1A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Use the MG362x1A WEB UPDATES Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-1
Use a USB Memory Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-3
Appendix C — Software Option Upgrades
C-2 Exporting a Software Configuration File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
C-3 Importing Software License . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1
Appendix D — Software Installation
PC Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1
D-2 FILE (File Management) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-2
Appendix E — Instrument Messages
E-2 Error Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-1
E-3 Informational Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-3
E-4 Warning Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-5
E-5 Self-Test Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E-6

1-6 PN: 10370-10383 Rev. E MG362x1A OM
Table of Contents (Continued)

MG362x1A PN: 10370-10383 Revision D 1-1
Chapter 1 — General Information
1-1 About this Guide
This manual provides general and operating information for the Anritsu series MG362x1A synthesized signal
generator. Throughout this manual, the terms MG362x1A, signal generator, and synthesizer will be used
interchangeably to refer to the instrument.
1-2 About this Chapter
This chapter contains general information about the series MG362x1A signal generators. It includes a general
description of the instrument and information on its identification number, related manuals, options, and
performance specifications.
1-3 Additional Documentation
For additional information and literature covering your product, visit the product page of your instrument and
select the Library tab:
https://www.anritsu.com/en-us/test-measurement/products/mg362x1a
Table 1-1. Related Manuals
Document Part Number Description
10100-00070 Product Information, Compliance, and Safety Notices
10100-00031 RF and Microwave Connector Care
11410-00928 MG362x1A Technical Data Sheet
10370-10385 MG362x1A Programming Manual
10370-10386 MG362x1A Maintenance Manual

1-4 Description General Information
1-2 PN: 10370-10383 Revision D MG362x1A
1-4 Description
The series MG362x1A synthesized signal generators are microprocessor-based, synthesized signal sources with
high resolution phase-lock capability. The MG362x1A is the "ideal microwave signal generator," offering
frequency coverage from 9 kHz to 70 GHz and provides the lowest phase noise, leveled output power, spectral
purity, switching speed, AM, FM, Phase and Pulse modulation performance, upgradability, reliability, and
service. Accepts GNSS as well as accepts and provides 1600 MHz, 100 MHz, 10 MHz ±100 Hz, 0 to 10 dBm
time-base signals. Our signal generators are configurable for a broad range of applications from R&D to
manufacturing and depot repair. Anritsu provides a total solution including proven reliability and standard 3
year warranty plus pre-sale and post-sale support that is the best in the industry. All functions of the signal
generator are fully controllable locally from the front panel or remotely (except for power on/standby) via
Ethernet (raw sockets over TCP/IP) or GPIB (IEEE-488 interface bus).
1-5 Instrument Integrity
The MG362x1A is configured for optimum signal generator performance when the instrument leaves the
factory. To maintain the system’s operating integrity, it is best to put the instrument into standby from the
front panel before cycling power.
Antivirus Protection
The MG362x1A is tested with most common antivirus software, but stability is not guaranteed with all anti-
virus software. Anritsu recommends connecting the instrument only to a secure network. The user assumes
the responsibility to provide virus protection because this is not supplied with the instrument. Contact your
network administrator for information about your network security and antivirus protection policies.
Figure 1-1. MG36221A Synthesized Signal Generator

General Information 1-6 ESD Caution
MG362x1A PN: 10370-10383 Revision D 1-3
1-6 ESD Caution
Connection of coaxial cables carrying an electrostatic potential, excess power, or excess voltage can damage the
internal circuitry of the signal generator. Operators must be aware of the potential for ESD damage and take
all necessary precautions. Operators should exercise practices outlined within industry standards such as
JEDEC-625 (EIA-625), MIL-HDBK-263, and MIL-STD-1686, which pertain to ESD and ESDS devices,
equipment, and practices. Because these apply to the MG362x1A, Anritsu recommends that any static charges
that may be present be dissipated before connecting coaxial cables to the signal generator. It is important to
remember that the operator may also carry a static charge. Following the practices outlined in the referenced
standards will ensure a safe environment for both personnel and equipment.
1-7 Instrument Care and Preventive Maintenance
The MG362x1A signal generator care and preventive maintenance consists of cleaning the unit and inspecting
and cleaning the RF connectors on the instrument and all accessories. Clean the signal generator with a soft,
lint-free cloth dampened with water or water and a mild cleaning solution.
Cleaning the Fan Grill
The signal generator must always receive adequate ventilation. A blocked fan grill can cause the instrument to
overheat and shut down. Clean the fans as follows:
1. Disconnect the MG362x1A from the power source.
2. Carefully vacuum the fan filters from the outside to clean them.
Connector Care
Refer to the Anritsu RF and Microwave Connector Care Instruction Sheet for recommended connection
procedures, connector care, and maintenance.
https://www.anritsu.com/en-us/test-measurement/support/downloads/manuals/dwl20373
Power Output
The MG362x1A is capable of output s in excess of +30 dBm. Ensure that proper care is taken to protect
sensitive power sensors from being damaged by using a fixed attenuator.
1-8 Unpacking the Product
Inspect the shipping container for damage. Retain the shipping container or cushioning material if they are
damaged until the contents of the shipment have been checked against the packing and the signal generator
has been checked for specified operation. If the shipment is incomplete or if the signal generator is damaged
mechanically or electrically, notify your local sales representative or Anritsu Customer Service. If either the
shipping container is damaged or the cushioning material shows signs of stress, notify the carrier as well as
Anritsu. Keep the shipping materials for the carrier’s inspection.
1-9 Operating Environment
Before installing the MG362x1A in its operating environment, ensure that all airflow passages at the sides and
rear of the instrument are clear. Proper ventilation is of particular importance whenever the unit is being rack
mounted. See the MG362x1A Technical Data Sheet for environmental requirements (11410-00928).
Caution To avoid damaging the display or covers, do not use solvents or abrasive cleaners.

1-10 Typographic Conventions General Information
1-4 PN: 10370-10383 Revision D MG362x1A
1-10 Typographic Conventions
Sequential menu successions are presented as a string of actions separated with a vertical pipe. For example,
to trigger a level-sweep:
Press: SWEEP | LEVEL | TRIGGER
1-11 Preparation for Storage/Shipment
The following paragraphs give instructions for preparing the MG362x1A for storage or shipment.
Preparation for Storage
Preparing the signal generator for storage consists of cleaning the unit, packing the inside with
moisture-absorbing desiccant crystals, and storing the unit in a temperature environment that is maintained
between –40°C and +75°C.
Preparation for Shipment
To provide maximum protection against damage in transit, the signal generator should be repackaged in the
original shipping container. If this container is no longer available and the unit is being returned to Anritsu for
repair, advise Anritsu Customer Service; they will send a new shipping container free of charge. In the event
neither of these two options is possible, instructions for packaging and shipment are detailed on the next page.
Use a Suitable Container
Obtain a corrugated cardboard carton with a 125 kg test strength. This carton should have inside dimensions
of no less than 15 cm larger than the unit dimensions to allow for cushioning.
Cushion the Instrument
Cushion the instrument on all sides by tightly packing dunnage or urethane foam between the carton and the
unit. Provide at least three inches of dunnage on all sides. Surround the unit with polyethylene sheeting to
protect the finish.
Seal the Container
Seal the carton by using either shipping tape or an industrial stapler.
Address the Container
If the instrument is being returned to Anritsu for service, mark the address of the appropriate Anritsu service
center and your return address on the carton in one or more prominent locations.
1-12 Contacting Anritsu for Sales and Service
To contact Anritsu, visit the following URL and select the services in your region:
http://www.anritsu.com/contact-us
Instrument Identification
All Anritsu instruments are assigned a unique six-digit ID number, such as “020312”. The ID number is
imprinted on a decal that is affixed to the rear panel of the unit. Special-order instrument configurations also
have an additional special number tag attached to the rear panel of the unit, such as SM1234.
When ordering parts or corresponding with Anritsu Customer Service, please use the correct serial number
with reference to the specific instrument's model number.

MG362x1A OM PN: 10370-10383 Rev. E 2-1
Chapter 2 — Instrument Overview
2-1 Introduction
This chapter provides an overview of the Anritsu MG362x1A signal generator. It describes the instrument
hardware features, touch screen display, general system settings and instrument configurations, and the
connector panels.
2-2 Front Panel
The MG362x1A front panel consists of the Graphical User Interface (GUI) and the data entry area.
The following sections provide a brief description of the front panel controls and data entry areas shown in
Figure 2-1. See Section 2-7 “GUI Overview” on page 2-10.
1. Power Button: Press the power button to power the signal generator on and off. Standby (off) is indicated by the
white illuminated power button; Operate (on) is indicated by the green illuminated power button.
2. Model Identification Label: Identifies the model type and frequency range.
3. LCD Display: The LCD display provides information about the current status of the MG362x1A in a menu display
format. This information includes the operating mode of the instrument and the value of the active frequency and
parameters. The display functions as a touch-screen interface to provide access to graphical button controls and
additional setting menus.
4. Front Panel Buttons: The front panel buttons provide controls for changing parameter values.
5. RF Output Control Key: The RF output control key turns the RF output power on and off. Output Off is indicated
by an orange LED; Output On is indicated by a green LED.
6. RF Output Connector: The RF output connector provides the 50 ΩRF signal output. Before making connections
to the RF output connector, see “Torque Requirements” on page 2-3.
7. Front Panel BNCs: Available with Option 29. Input BNCs are AM IN, FM/ΦM IN, Pulse IN, External ALC IN).
8. Handles: Standard configuration includes handles.
9. USB Interface: Four front panel Type A USB Inputs.
Figure 2-1. MG362x1A Front Panel Overview
4 5
6
9
7
8
21 3

2-2 Front Panel Instrument Overview
2-2 PN: 10370-10383 Rev. E MG362x1A OM
Front Panel Controls
Use the numeric keypad, arrow hard buttons, or rotary data knob to change the MG362x1A parameter value.
The data entry area is shown in Figure 2-2 and described in the following paragraphs.
Menu Buttons
Frequency: Press to access the frequency menu.
Level: Press to access the level menu.
ALT: Non-Functional
Rotary Knob
Use the rotary knob to change the value of a parameter that is open for editing. The cursor is moved under the
open parameter using the left or right pad cursor control pads. Turn the rotary knob clockwise to increase the
parameter or counterclockwise to decreased by the parameter unit size. The unit size is determined by the
cursor placement. Turn the knob rapidly changes the value in larger steps.
When editing frequency and time parameters, the incremental size can be set to using the system
configuration increment menu. Refer to “INCREMENT Menu” on page 3-79. Once set, each time the knob is
turned clockwise or counter-clockwise, the parameter's value increases or decreases by the set unit amount.
Cursor Control Pad
The left and right pads control the direction of the cursor when editing a parameter. Press the left keypad to
move the cursor left to edit an open parameter. Press the right keypad to move the cursor right to edit an open
parameter. Press the top keypad to increase a units value, Press the bottom keypad to decrease the units
value. Press and hold will allow the selected parameter to continually increase or decrease. Press Select to
enter an opened single terminator value.
1. Menu Hard Keys
2. Rotary Knob
3. Cursor Control Pad
4. Numeric Keypad
Figure 2-2. Front Panel Controls
2
3
1
4

Instrument Overview 2-2 Front Panel
MG362x1A OM PN: 10370-10383 Rev. E 2-3
Numeric Keypad
The numeric keypad provides for entering frequency, , time, number-of-steps, modulation parameters, and
GPIB address values. The “+/–” key functions as a “change sign” key during any keypad entry.
RF Output
The front panel output connector panel is described in Figure 2-3.
Torque Requirements
To avoid connector damage or inaccurate measurements, review document 10100-00031Connector Care
Reference before making any connections.
N-Type Connector: Torque to 0.9 N-M (8in-lb) for standard N connectors using Anritsu Model 01-203 13/16 in
Torque End Wrench.
K (2.92 mm) Connector: Torque to 0.9 Nm (8 lbf·in) using Anritsu Model 01-201 5/16 in Torque End Wrench
and Anritsu Model 01-204 - 8 mm (5/16 in) Open End Wrench.
V Connector: Torque to 0.9 Nm (8 lbf·in) using Anritsu Model 01-201 5/16 in Torque End Wrench and Anritsu
Model 01-204 - 8 mm (5/16 in) Open End Wrench.
Unleveled Indicator: The unleveled indicator is displayed when the RF output goes
unleveled and is normally caused by exceeding the specified leveled power rating.
RF On/Off: Press to manually turn RF output on or RF output off.
RF Output Connector: The female RF output connector. The 50 Ωoutput connector is:
K for the 20 GHz model MG36221A
K for the MG36241A model
V for the MG36271A model
CAUTION Label: The output power may exceed +30 dBm. Attenuate output power as
necessary to protect RF test equipment from excessive output power when connecting to
the output connector.
Figure 2-3. RF Output Panel
Note To prevent power losses due to an impedance mismatch, the mating connector and cable should
also be rated at 50 Ω

2-3 Rear Panel Instrument Overview
2-4 PN: 10370-10383 Rev. E MG362x1A OM
2-3 Rear Panel
This section provides descriptions for the rear panel connectors on a typical Series MG362x1A RF/Microwave
signal generator.
Table 2-1 provides an overview of the MG362x1A rear panel.
Note Connectors are option dependent.
Table 2-1. Rear Panel Overview
Index Description
1 Input/Output BNCs. See “Rear Panel BNCs” on page 2-5.
2 Two USB 3.0 Type-A for peripherals such as memory device.
3 One USB 2.0 Type-B for USB-TMC.
4 AC Input connector, with On/Off switch, and fuses 350 VA maximum, 90 to 264 VAC, 47 Hz to 63 Hz
5 Accepts an external SDIO memory card.
6Fan
7 Provides input/output connections for a Gigabit Ethernet interface. RJ45 type, rear panel
8 Provides input/output connections for the General Purpose Interface Bus (GPIB).
9 AUX2 I/O: 25-pin connector - Future capability
10 AUX1 I/O: 15 Pin connector - Future capability
11 Fan: Instrument air-intake fan. Do not block airflow or the instrument may overheat.
12 Cover plates: Not Used
41 3
2
12
11 10 9 8 7 6 5

Instrument Overview 2-3 Rear Panel
MG362x1A OM PN: 10370-10383 Rev. E 2-5
Rear Panel BNCs
The MG362x1A rear panel BNCs are described in Figure 2-4.
AM OUT: Provides the amplitude modulation waveform from the internal LF generator. Enabled with Option 027.
(BNC type, rear panel)
HORIZ OUT: Provides 0 V at beginning and +10 V at end of sweep, regardless of sweep width. In CW mode, the
voltage is proportional to frequency between 0 V at low end and +10 V at the high end of the range. In CW mode, if
CW RAMP is enabled, a repetitive, 0 V to +10 V ramp is provided.(BNC type, rear panel)
PULSE OUT: Provides a video modulating signal from the internal pulse generator. Enabled with Option 027.
(BNC type, rear panel)
FM OUT: Provides the frequency or phase modulation waveform from the internal LF generator. Enabled with
Option 027. (BNC type, rear panel)
EXT TRIG: Accepts a TTL low-level signal of 1 s width to trigger a sweep. (BNC type, rear panel)
PULSE SYNC: Provides a TTL compatible signal, synchronized to the internal pulse modulation output. Enabled
with Option 026. (BNC type, rear panel)
LOCKED/LEVELED: TTL high/low output signal when in internal ALC mode that is a logical AND of frequency
locked condition and output leveled condition. When in Fixed Gain mode this signal indicates only frequency
locked/unlocked condition. (BNC type, rear panel)
PPS: 1PPS input/output from either GNSS/GPS atomic clock receiver or internal rubidium reference option.
(3.3V CMOS I/O, BNC type, rear panel)
FM IN: Accepts an external signal to frequency or phase modulate the RF output signal. Enabled with Option 012.
50 Ωimpedance. (BNC type, rear panel)
EXT ALC: Provides for leveling the RF output signal externally with either a detector or power meter. Signal
requirements are shown in the RF Output specifications. (BNC type, rear panel)
EFC: ±4 VDC 30 Hz bandwidth in wide reference PLL mode 1 MΩinput impedance. Provides the capability to
frequency modulate the internal crystal oscillator, allowing phase locking of the synthesizer inside an external lock
loop. (BNC type, rear panel)
AM IN: Accepts an external signal to amplitude modulate the RF output signal. Enabled with Option 012. 50 Ω
impedance. (BNC type, rear panel)
10 MHZ REF IN: Accepts an external 10 MHz ± 3 Hz, 0 dBm to +10 dBm (20 dBm no-damage level) time-base
signal. Automatically disconnects the internal high-stability time-base option, if connected. 50 Ωimpedance input
(BNC type, rear panel)
10 MHZ REF OUT: Provides a 10 dBm, AC coupled, signal derived from the internal frequency standard.
(50 Ωimpedance, SMA type, rear panel
Figure 2-4. Rear Panel BNCs
FM OUT LOCKED/LEVELED EXT ALC 10 MHz
REF IN
100 MHz
REF IN
1600 MHz
REF IN
AM OUT
HORIZ OUT EXT TRIG PPS EFC 10 MHz
REF OUT
100 MHz
REF OUT
1600 MHz
REF OUT
GPS
PULSE INAM INFM INPULSE SYNCPULSE OUT

2-3 Rear Panel Instrument Overview
2-6 PN: 10370-10383 Rev. E MG362x1A OM
PULSE IN: Accepts an external TTL compatible signal to pulse modulate the RF output signal or to trigger or to gate
the optional internal pulse generator. Enabled with Option 026. (BNC type, rear panel)
100 MHZ REF IN: Accepts an external 100 MHz ± 200 Hz or 2 ppm 12 ± 1 dBm (20 dBm no-damage level)
reference signal. Enabled with Option 003 or 013. Automatically disconnects the internal high-stability time-base
option, if connected. (50 Ωimpedance, SMA type, rear panel
100 MHZ REF OUT: Provides a 12 dBm, AC coupled, 100 MHz signal derived from the internal frequency standard.
Enabled with Option 003 or 013. (50 Ωimpedance, SMA type, rear panel
1600 MHZ REF IN: Accepts an external 1600 MHz ± 3.2 kHz or 2 ppm, 4 ± 1 dBm (20 dBm no-damage level)
reference signal. Enabled with Option 003 or 013. Automatically disconnects the internal high-stability time-base
option, if connected. (50 Ωimpedance, SMA type, rear panel
1600 MHZ OUT: Provides a 5 dBm, AC coupled, 1600 MHz signal derived from the internal frequency standard.
Enabled with Option 003 or 013. (50 Ωimpedance, SMA type, rear panel
GNSS/GPS: Accepts GNSS/GPS antenna input.

Instrument Overview 2-4 Installation and Power Requirements
MG362x1A OM PN: 10370-10383 Rev. E 2-7
2-4 Installation and Power Requirements
The signal generator accepts 90 to 264 VAC, 47 Hz to 63 Hz, single-phase, AC mains input power. The signal
generator is intended for Installation Category (Over Voltage Category) II. To connect the MG362x1A to the
power source, plug the female end of the power cable into the input line voltage receptacle on the rear panel as
shown in Figure 2-5. Then plug the male end of the power cord into a three-wire power line outlet. Turn on the
rear panel power button. This automatically places the signal generator in operation (front panel Operate LED
on).
2-5 Powering On the MG362x1A
Connect the MG362x1A to an AC power source. Turn on the rear panel power button as shown in Figure 2-5.
This automatically places the signal generator into operation (front panel green Operate LED on). During
power on and power down, the orange LED blinks for five to ten seconds.
Warning
When supplying power to this equipment, always use a three-wire power cable connected to a
three-wire power line outlet. If power is supplied without grounding the equipment in this manner,
there is a risk of receiving a severe or fatal electric shock.
1. Power Button
2. AC Mains Input
Figure 2-5. Rear Panel Power Connection
GPIB SD CARD
AUX1 AUX2
FM OUT LOCKED/LEVELED EXT ALC 10 MHz
REF IN
100 MHz
REF IN
1600 MHz
REF IN
AM OUT
HORIZ OUT EXT TRIG PPS EFC 10 MHz
REF OUT
100 MHz
REF OUT
1600 MHz
REF OUT
GPS
PULSE INAM INFM INPULSE SYNCPULSE OUT
NO OPERATORSER VICE-
ABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED PERSONNEL.
WARNING
1
2
Do not operate
with power cord
ungrounded.
CAUTION
90-264 VAC
47-63 Hz
350 VA max
INPUT
For continued re protection,
replace only with specied
type and rated fuse.
CAUTION
T 6.3 A 250 V
230 V
Anritsu Company
490 Jarvis Drive
MorganHill,CA 95037-2809
WTO COOUS
CAN ICES-1(A)/NMB-1(A)
KCC-REM-A2J-0004

2-5 Powering On the MG362x1A Instrument Overview
2-8 PN: 10370-10383 Rev. E MG362x1A OM
Power on the signal generator. The front panel display is shown as in Figure 2-6 during power-on. The power
on sequence shows the loading internal programs status-bar, the model number of the signal generator, the
options installed, and the revision level of the installed firmware. When complete, the MG362x1A then returns
to the same configuration it was in when last set to Standby.
Standby Mode
Whenever the signal generator is not being used, it should be left connected to the power source and placed in
standby. Standby mode provides power to keep the internal time base at operating temperature. This assures
specified frequency accuracy and stability when the MG362x1A is placed in operation.
Warm-up Time
After placing the MG362x1A into operation mode, allow 30 minutes of warm-up time to ensure stable
operation.
From a cold start (0 C), the signal generator requires approximately 120 hours (5 days) of warm-up to achieve
specified frequency stability with aging.
Figure 2-6. Startup Screen
Note
The Ref Cold message may appear on the MG362x1A user interface task bar when the instrument is
first powered on from a cold condition. The message may be displayed for a few minutes until the
lock circuitry has reached the operational temperature. This warning message may display for units
with Option 3, 13, 23, 56, and 66.
Note Instruments disconnected from AC power for more than 72 hours require 30 days to return to
specified aging.
Model: MG36221A Software Version T2021.3255 20210915_160802
Options: 0002/0003/0004/0013/0015/0016/0056/0066
Loading...