ANTAIRA AMS-7131-AC Series User manual

Antaira Technologies
AMS-7131-AC Series
Industrial 802.11a/b/g/n/ac Wi-Fi Access
Point/Client/Bridge/Repeater
Quick Installation Guide
Version 1.0
(January 2019)
Tel: [phone]
Fax: [phone]
www.antaira.com
Package Check List
The package contains the following items:
⚫1 –Quick Installation Guide
⚫1 –AMS-7131-AC Series
⚫1 –Wall Mounting Bracket Set with Screws
⚫1 –Terminal Block
⚫2 –External Antennas
Front Panel Layout
Top Panel View
AMS-7131-AC Series’top panel is equipped with one 6-pin
removal terminal block connector for dual DC power inputs
(9~48VDC).
Product Overview
System Interface/Performance
Qualcomm Atheros QCA9892
2*10/100Tx RJ45 Ethernet Ports
WLAN Supports 2.4GHz Wi-Fi
Two External SMA Antenna
Power Input & Connection
DC 9~48V a 6-Pin Removal Terminal Block
Operating Temperature
Standard Operating Temperature: 0°C to 60°C
Extended Operating Temperature (-T): -35°C to 75°C
Case/Installation
IP30 Protection
Installation in a Pollution Degree 2 Industrial Environment
DIN-Rail and Wall Mount Design
LED Indicators
LED
Color
Description
Power 1
Green
On
Power input 1 is active
Off
Power input 1 is inactive
Power 2
Green
On
Power input 2 is active
Off
Power input 2 is inactive
Fault
Red
On
Power input 1 or 2 is inactive
Off
Preconfigured alarms are detecting failure
Wi-Fi Signal
Strength
Green/Red
Red
Less than 25% signal strength
Green
LED 2 Less than 50% signal strength
Green
LED 3 Less than 75% signal strength
Green
LED 4 Less than 100% signal strength
ETH Ports 1 & 2
(ACT)
Green
On
Connected to network, 10/100Mbps
Flashing
Networking is active
Off
Not connected to network
ETH Ports 1 & 2
(LINK)
Amber
Amber
Link established
Off
No Link detected
Quick Installation
Ethernet Ports
RJ45 Ports (Auto MDI/MDIX)
All RJ45 ports are auto-sensing for 10Base-T and 100Base-TX
device connections. Please follow the wiring pin assignment
table below for Ethernet port installation.
Grounding Screw
(Behind)
Reset Button
LED for Activity Status
LED for Link Status –10/100Tx
LED for P1, P2, and Fault
Grounding Screw
6-Pin Removal Terminal Block
(Power Input)
Wi-Fi Signal Strength
Ethernet Port
Antenna Mount
Terminal Block

Power Input Wiring
Please follow the steps below to insert the power wire:
1. Insert the positive and negative wires into the V+, V-
contacts on the terminal block connector as shown
below in Figure 1.
2. Tighten the wire-clamp screws to prevent the wires from
loosening, as shown below in Figure 2.
Figure 1
Figure 2
Industrial Switch Mounting
DIN-Rail Mounting
The DIN-Rail bracket is pre-installed on the
industrial Ethernet switch from the factory.
Please refer to Figure 3 for a DIN-Rail
bracket installation reference. Follow the
steps below for installing the industrial
switch on the DIN-Rail track:
1. Insert the top of the DIN-Rail onto the
track as shown below in Figure 4.
2. Lightly pull down the bracket onto the
rail as shown below in Figure 5.
3. Check if the bracket is mounted tightly
on the rail.
4. To remove the industrial
Ethernet
switch
from the rail, do the opposite from the steps above.
Figure 4
Wall Mounting
Follow the steps below to mount the industrial Ethernet switch
using the wall mounting bracket as shown below in Figure 6.
1. Remove the DIN-Rail bracket from the industrial Ethernet
switch by loosening the screws.
2. Place the wall mounting brackets on the top and bottom of
the industrial Ethernet switch.
3. Use the screws to screw the wall mounting bracket on the
industrial Ethernet switch.
4. Use the hook holes at the corners of the wall mounting
bracket to hang the industrial Ethernet switch on the wall.
5. To remove the wall mount bracket, do
the opposite from the steps above.
Field Maintenance and Service
⚫If the device requires servicing of any kind, the user is
required to disconnect and remove it from its mounting. The
initial installation should be done in a way that makes this as
convenient as possible.
⚫Voltage/power lines should be properly insulated as well as
other cables. Be careful when handling them so as to not trip
over.
⚫Do not under any circumstance insert foreign objects of any
kind into the heat dissipation holes located in the different
faces of the device. This may not only harm the internal
layout, but might cause harm to the user as well.
⚫Do not under any circumstance open the device for any
reason. Please contact your dealer for any repair needed or
follow the instructions within the manual.
Warranty Policy
Warranty Conditions
Products supplied by Antaira Technologies are covered in this
warranty for sub-standard performance or defective
workmanship. The warranty is not, however, extended to goods
damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock,
earthquake
(c) Use of unqualified power supply, connectors, or
unauthorized parts/kits
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA" number
from Antaira before shipping the goods for repair or
replacement.
•Within the warranty period (based on the invoice date), all
parts and labor are free of charge to the customers.
•Customers are responsible for the cost of parts and labor, if
the products are out of warranty.
•For RMA service, customers are responsible for the shipping
expense for shipping the RMA unit(s) to Antaira. Antaira is
responsible for the shipping expense via a ground service
for the return repair/replace unit(s) back to customers.
Limited Liability
Antaira would not be held responsible for any consequential
losses from using Antaira’s product.
Warranty Period
5-Year Warranty
Antaira’s Customer Service and Support
•Antaira’s Technical Service & Support Centers:
+ 844-268-2472 (Antaira US Headquarter)
+ 48-22-862-88-81 (Antaira Europe Office)
+ 886-2-2218-9733 (Antaira Asia Office)
•Antaira’s Web Sites & Repair/Support Emails:
www.antaira.com / [email protected]
www.antaira.eu / [email protected]
www.antaira.com.tw / [email protected]
*Any changes will be announced on the Antaira website.
Figure 3
Figure 6
Figure 5