Anthro Zido Single Monitor Mount User manual

ASSEMBLY INSTRUCTIONS
Anthro | 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone] | email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone] | Fax: [phone]
Zido®Single Monitor Mount
March 2016
Product Part#
Zido Single Monitor Mount ZOMSzz

WELCOME
Thank you for purchasing the Zido
Single Monitor Mount.
If you have any questions or if we
can help you in any way, please
contact us at 800.325.3841.
A 5/32" hex driver (provided with
your Zido Cart) is required for this
assembly.
PARTS LIST
Before beginning assembly of your Zido Single Monitor
Mount, please review the parts list to verify that your
shipment is complete.
2
Fastener quantities listed are the minimum needed for your assembly.
Your shipment may contain a few extras.
Zido Pole Flat Panel Mount, Single Quantity Part Number
01 Outer Bracket 1 225-2661-00
02 Inner Bracket 1 225-2980-00
03 1/4-20 x 1/2" Button Head Screw 4 325-5003-00
04 #10-24 x1/2" Self-threading Screw 2 325-5464-00
05 OmniMount Small Tilt/Pan Mount 1 835-5764-00
06 M6 x 12mm Button-head Screw 2 325-5757-00
07 OmniMount VESA Plate 1 697-915-00
08 Flat Pattern Hardware Kit (not shown) 1 697-563-00
M4 x 12mm Philips Head Screw 4 M-A
M5 x 12mm Philips Head Screw 4 M-B
(not needed in assembly)
M6 x 12mm Philips Head Screw 4 M-C
(not needed in assembly)
09 OmniMount Hardware Kit (not shown) 1 697-878-00
Security Allen Screw 2 P-C
Washer 2 P-D
Allen Wrench 1 P-E
07
01
02
03
04
05
06

Zido Single Monitor Mount Assembly Instructions 3
STEP 1
Attach the VESA plate to your monitor
Place the VESA bracket in position on the back of the monitor. Attach using four
M4 x 12MM Screws (part #M-A) provided in the plastic bag. The VESA bracket
accommodates 75mm and 100mm hole patterns. For this installation, you may also
use the screws that came with your monitor.
STEP 2
Assemble the Brackets
Align the Tilt/Pan Mount with the 2 outer holes that are directly above and below
the 6 small holes in the center of the outer bracket. Secure using 2 M6 x 12mm
Button-head Screws using the 5/32" hex key. (A)
Slide the inner bracket into the outer bracket so that the holes on each side align.
Using the 5/32” hex key, secure with 4 1/4-20 x 1/2" Button-head Screws. (B)
STEP 3
Install the Brackets and the Monitor
Slip the bracket assembly over the top of the Zido tube, with the assembly facing
the front of the cart. Be sure the assembly is installed right side up, with the curved
slot being at the top of the assembly (A). Secure with 2 self-threading screws. (B).
Note: These fasteners are creating the threads in the tube, so the first few turns will require some force.
Lift the monitor into place in front of the Tilt/Pan Mount. Slide the VESA bracket
into the curved slot in the Tilt/Pan Mount.
Secure the monitor to the Tilt/Pan Mount using 2 Security Allen Screws (part #
P-C) using the Allen Wrench (part #P-E), making sure to place a washer (part #P-D)
between the screw and the VESA plate.
To adjust the position of the monitor, loosen the knob on the side of the Tilt/Pan
Mount to adjust and tighten again when the monitor is in the desired position.
CONGRATULATIONS!
YOUR ZIDO SINGLE MONITOR MOUNT ASSEMBLY IS COMPLETE!
Self-threading Screw
325-5464-00
A.
B.
Top of assembly
Curved Slot
Knob
Knob
A.
B.
Self-threading
Screws
Outer Hole
M6 x 12MM Screws
1/4-20 X 1/2"
Button-head Screws
1/4-20 x1/2” Button-hd Screw
3
2
5
-
5003
-
00
M6 x 12mm Button-hd Screw
325-5757-00

*300-5666-00*
300-5666-00
Anthro | 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone] | email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone] | Fax: [phone]
Warranty:
For warranty information, please visit: anthro.com/support/warranty
Notices:
Anthro logo is a registered trademark of Ergotron, Inc. © 1994 - 2016; Anthro-DNA is a trademark of Ergotron Inc., © 2016.
All rights reserved. Anthro is also a brand of Ergotron Inc., a Nortek company.