Anthro METBK User manual

WELCOME
Hello! Thank you for choosing Anthro.
These instructions describe the
installation of Anthro's Monitor Easy
Track. If you have any questions or
if we can help you in any way, please
contact Anthro at 800.325.3841.
TOOLS
You will need a 17/64" drill bit and
power drill.
PARTS LIST
Before beginning this assembly, please take a moment to
review the parts list below to verify that your shipment
is complete. The mounting surface (shown shaded) is not
included with this accessory.
1
Product Quantity Part Number
011 Monitor Easy Track 1 835-MET
02 Nylock Nuts 4 325-5259-00
03 Button Head Screws 4 325-5034-00
04 Washers 8 325-5120-00
10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone] | email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone] | Fax: [phone]
ASSEMBLY INSTRUCTIONS
Monitor Easy Track®
01
02
03
04
Part Number: METBK

Questions? Call us at 800.325.3841 or visit anthro.com. We’re happy to walk you through the assembly!
CONGRATULATIONS! YOUR MONITOR EASY TRACK ASSEMBLY IS COMPLETE!
*300-5635-00*
300-5635-00
Rev A September 2015
Warranty:
For warranty information, please visit:
http://www.anthro.com/support/warranty
STEP 1
Place the Monitor Easy Track on Your Work
Surface
Clear off installation site so you can access the top and bottom of
the work surface.
Remove the Monitor Easy Track from the box. With the assistance
of another person, lift and place it on the work surface (A). The
gray handle must face the user. With the unit closed (the boom
will be furthest away from the user), position it where you want
the track mounted to the surface.
Without moving the unit base, open up the Monitor Easy Track by
squeezing the handle and pull the boom toward you. Once the
unit is in the open position, locate the 4 mounting holes in the
base that will be exposed (B). Use a pen or pencil to mark the 4
holes where you will be drilling.
STEP 2
Drill holes in Your Work Surface
Close the Monitor Easy Track and remove it from the surface with
the assistance of another person. Gently place it aside and out of
the way. Using a 17/64" drill bit, carefully drill straight down and
all the way through the surface. Continue with drilling all 4 holes.
STEP 3
Attach the Monitor Easy Track to Your Work
Surface
Once holes are drilled, be sure the drilled holes and surface are
cleared of debris. Place the Monitor Easy Track back onto the
surface with the assistance of another person. Open the Monitor
Easy Track by squeezing the handle and moving the boom toward
you.
Line up the holes on the unit base with the holes that you drilled.
Place a washer onto the screw, put the screw and washer through
the first hole from the top of the surface. Place a second washer
onto the screw from the underside of the surface. (For best results,
this will require you to work beneath the work surface.) Secure
with a Nylock nut and tighten onto the screw using a 5/32 hex
driver and a 7/16 nut driver. (This works best having someone hold
the hex driver in place while the other person is below the desk
tightening the Nylock nut.)
Repeat this process for the remaining 3 holes.
B
A
Mounting Holes
Handle
Handle
Nylock Nut
Washer
Washer
Screw
17/64" Drill Bit
Notices: Technology Furniture® and Monitor Easy
Track® are registered trademarks of
Anthro. Anthro reserves the right to modify the
design and specifications without prior notice.
2” Button-head Screw
325-5034-00
Handle
1/4-20 Nylock Nuts
325-5259-00
Boom
Boom
Boom
Anthro Corporation is a wholly owned subsidiary of
Ergotron Inc., a Nortek company