Anthro The Peanut PT1GMPW3 User manual

ASSEMBLY INSTRUCTIONS
Anthro Corporation®| 10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone] | email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone] | Fax: [phone]
The Peanut
May 2014
NOTE: The Peanut, Tall, is shown. The tablet and keyboard are not included.
Product Part#
The Peanut PT1GMPW3
The Peanut for Tablets PT2GMPW3
TM

WELCOME
Thank you for purchasing The Peanut.
If you have any questions or if we can
help you in any way, please contact us
at 800.325.3841.
TOOLS
The Peanut comes with these tools:
• 3-way wrench
Not provided, but suggested:
• 7/16" nut driver
• 3/8" nut driver
PARTS LIST
Before beginning assembly of The Peanut, please review the
parts list to verify that your shipment is complete.
2
Product Quantity Part Number
01 Shelf 1
for The Peanut 225-4834-00
for The Peanut for Tablets 225-4837-00
02 Handle (installed on shelf) 1 125-5411-00
03 Column Assembly 1
for The Peanut 500-1108-00
for The Peanut for Tablets 500-1109-00
04 Cable Sleeve 1 280-5056-00
05 Base 1 225-4833-00
06 Casters, Non-locking 2 150-5117-00
07 Casters, Locking 2 150-5118-00
08 1/4-20 Nylock Nut 24 325-5259-00
09 VESA Tilt Assembly 1 835-5639-00
for Peanut for Tablets
10 Easel Assembly 1 835-5640-00
for Peanut for Tablets
11 #10-24 x 0.75" Flat Head Screw 2 325-5270-00
for Peanut for Tablets (not shown)
10
09
For Peanut for Tablets:
01
02
03
04
05
06
07
08

The PeanutTM Assembly Instructions 3
STEP 3 - ATTACH SHELF TO COLUMN AND CABLE SLEEVE
Stand the column up on its casters.
Align mounting holes on column with bolts
in shelf so the handle is over the locking
casters.
Attach the shelf with four nylock nuts using
a 7/16" nut driver.
Slip the Cable Sleeve over the tube and
press into place.
STEP 1 - ATTACH THE CASTERS TO THE BASE
Lay the base upside down on work surface or floor.
Align the mounting holes in each caster plate with the bolts sticking
out of the base. Locking casters (with tabs as shown) attach to the longer base
legs.
Attach each caster with four nylock nuts using a 7/16" nut driver.
STEP 2 - ATTACH BASE TO THE COLUMN
Align mounting holes in base with bolts
sticking out of the bottom of the column.
Attach the base with four nylock nuts using
a 7/16" nut driver.
1/4-20 Nylock Nuts
325-5259-00
1/4-20 Nylock Nuts
325-5259-00
1/4-20 Nylock Nuts
325-5259-00
Locking Casters

4Questions? Call us at 800.325.3841 or visit anthro.com. We’re happy to walk you through the assembly!
300-5610-00
300-5611-00
Anthro Corporation®
10450 SW Manhasset Dr. | Tualatin, OR 97062
Toll-free: 800.325.3841 | Fax: [phone]
email: [email protected] | anthro.com
Outside the U.S. | Tel: [phone]
Warranty:
For warranty information, please visit:
http://www.anthro.com/support/warranty
Notices:
Technology Furniture and The PeanutTM are trademarks of
Anthro Corporation. Anthro reserves the right to modify
the design and specifications without prior notice.
STEP 5A - ATTACH DEVICE HOLDER TO VESA PLATE
Align device holder with the VESA plate so the four threaded studs on the
holder line up with four holes on the plate.
Attach the device holder to the plate with four acorn nuts using your 3/8"
driver.
To adjust the device holder, loosen the adjustment knobs at the back of the
device holder, slide the top of the holder into position, then tighten the knobs.
STEP 5B - ATTACH TABLET CASE TO VESA PLATE
Align the holes in the back of your tablet case with the four outer holes in the
VESA mount.
Attach monitor with mounting screws that come with the case.
CONGRATULATIONS! YOUR CART ASSEMBLY IS COMPLETE!
STEP 4 - ATTACH VESA MOUNT TO COLUMN
Rotate VESA plate on mounting assembly so it can lay flat.
Align mounting holes in mounting assembly with holes in top of column.
Attach VESA mounting assembly with two hex bolts using 1/8" hex key.
#10-24 x 0.75” Flat-hd Screw
325-5270-00
3/8” Acorn Nut
325-5023-00