AOC 936Swa User manual

18.5" LCD Color Monitor AOC 936Swa
1
Service
Service
Service
HorizontalFrequency
30-80 kHz
TABLEOFCONTENTS
Description Page Description Page
Description Page
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Table Of Contents.......…….................……...........…........1
Revision List.…........................………................……......2
1. Monitor Specification.................................………........3
2.LCD Monitor Description…………………………….......4
3. Operation Instruction…………...................…...........5
3.1 General Instructions.....................................…...........5
3.2 Control Button……………………………..……...........5
3.3 Adjusting the Picture...........................…............5
4. Input/Output Specification............……………............8
4.1 Input Signal Connector............…..……................8
4.2 Factory Preset Display Modes.........................9
5 Panel Specification.....…………………........................10
5.1 Display Characteristics………………………………10
5.2 Optical Characteristics………………………………..10
5.3 Parameter guide line for CCFL Inverter……………..10
6.Block Diagram…….…................………….........11
6.1 Software Flow Chat…….…..........………….........11
6.2 Electrical Block Diagram………...………...…......13
7. Schematic……………………………………………. 15
7.1 Main Board…………..............................................15
7.2 Power Board....……………....................................19
8. PCB Layout..………….......................................21
8.1 Main Board……………......................................21
8.2 Power Board…......................................................22
8.3 Key Board……………….....................................24
9. Maintainability……….......................................25
9.1. Equipments and Tools Requirement.....................25
9.2. Trouble Shooting…………....................................26
10. White-Balance, Luminance adjustment.................31
11.Monitor Exploded View……..……………............33
12. BOM List....……....................................................34
13.Different Parts List……………………………….…..44
Table Of Contents.......…….................……...........…........1
Revision List.…........................………................……......2
1. Monitor Specification.................................………........4
2. LCD Monitor Description…………………………….......5
3. Operation Instruction…………...................…...........6
3.1 General Instructions.....................................…...........6
3.2 Control Button……………………………..……...........6
3.3 Adjusting the Picture...........................…............7
4. Input/Output Specification............……………............8
4.1 Input Signal Connector............…..……................8
4.2 Factory Preset Display Modes.........................8
5 Panel Specification.....…………………........................9
5.1 Display Characteristics………………………………9
5.2 Optical Characteristics………………………………..10
5.3 Parameter guide line for CCFL Inverter……………..13
6.Block Diagram…….…................………….........15
6.1 Software Flow Chart…….…..........………….........15
6.2 Electrical Block Diagram………...………...…......17
7. Schematic……………………………………………. 19
7.1 Main Board…………..............................................19
7.2 Power Board....……………....................................28
8. PCB Layout..………….......................................30
8.1 Main Board……………......................................30
8.2 Power Board….....................................................34
8.3 Key Board……………….....................................36
8.4 USB Board……………..........................................37
9. Maintainability………...............................................38
9.1. Equipments and Tools Requirement.....................38
9.2. Trouble Shooting…………....................................39
10. White-Balance, Luminance adjustment.................48
11.Monitor Exploded View……..……………............50
12. BOM List....……....................................................51
13.Different Parts List……………………………….…..60

18.5" LCD Color Monitor AOC 936Swa
2
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics might create
shock, fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiations when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)

18.5" LCD Color Monitor AOC 936Swa
3
Revision List
Version Date Revision History Remark
T89MM5NQ6WA16NE
T89AM5NB6WA2UNE
Initial release
T89SM5NB6WA1UNE
M185XW01
Add Panel list in Item 5
LTM185AT02
A00 Jun.-12-2009
Add Power Board in Item
7.1/8.1/9.2 715G3244 1

18.5" LCD Color Monitor AOC 936Swa
4
1. Monitor Specification
Model number 936Swa
Driving system TFT Color LCD
Viewable Image Size 470mm diagonal
Pixel pitch 0.3mm(H) x 0.3mm(V)
Video R, G, B Analog lnterface & Digital Interface
Separate Sync. H/V TTL
Display Color 16.7M Colors
LCD Panel
Dot Clock 85.5MHz
Horizontal scan range 30 kHz - 80 kHz
Horizontal scan Size(Maximum) 409.8mm
Vertical scan range 55 Hz - 75 Hz
Vertical scan Size(Maximum) 230.4mm
Optimal preset resolution 1366x768 (60 Hz)
Highest preset resolution 1366x768 (60 Hz) )
Plug & Play VESA DDC2B/CI
Input Connector D-Sub 15pin
Input Video Signal Analog: 0.7Vp-p(standard), 75 OHM
Power Source 100-240VAC, 50/60Hz
Typical < 25W
Power Consumption Standby < 1 W
USB Downstream port (A type ) To USB device, loading < 100mA
off timer 0~24hours Select timing to turn off the monitor.
Resolution
Speakers 1.5W x 2
Connector Type 15-pin Mini D-Sub
Signal Cable Type Detachable
Height (with base) 358.66mm
Width 463.14mm
Depth 186mm
Weight (monitor only) 3.63 kg
Physical
Characteristics
Dimensions & Weight:
Weight (with packaging) 5.02kg
Operating 0° to 40°
Temperature: Non-Operating -20°to 60°
Operating 10% to 85% (non-condensing)
Humidity: Non-Operating 5% to 80% (non-condensing)
Operating 0~ 3000m (0~ 10000 ft )
Environmental
Altitude: Non-Operating 0~ 5000m (0~ 15000 ft )

18.5" LCD Color Monitor AOC 936Swa
5
2. LCD Monitor Description
The LCD Monitor will contain main board, power board, key board which house the flat panel control logic,
brightness control logic and DDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
Power Board
(Include adapter and inverter)
Flat Panel and
CCFL backlight
Main Board RS232 Connector
For white balance
adjustment in
factory mode
HOST Computer
CCFT Drive.
AC-IN
100V~240V
Monitor Block Diagram
Key board
Video signal, DDC

18.5" LCD Color Monitor AOC 936Swa
6
3. Operation Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor.
By changing these settings, the picture can be adjusted to your personal preferences.
* The power cord should be connected.
* Press the power button to turn on the monitor. The power indicator will light up.
3.2 Control Buttons
Power Press to turn on or turn off the monitor.
4:3 or wide / Up Press key to change the screen aspect ratio between standard 4：3format or Wide format.
Auto / Down Auto configure hot key: When the OSD is closed, press Auto button to do auto configure.

18.5" LCD Color Monitor AOC 936Swa
7
3.3 Adjusting the Picture
OSD Settings
Eco mode ---DCR, Standard, Text, Internet, Game, Movie, Sports
Notes : When Eco mode is not set as “Standard”, Contrast and Brightness can not be adjusted; When DCR is set as
“On”, Contrast, Brightness, Eco mode and Gamma can not be adjusted.
LED Indicator

18.5" LCD Color Monitor AOC 936Swa
8
4. Input/Output Specification
4.1 Input Signal Connector
D-Sub mini 15pin Connector
Pin Number 15-Pin Side of the Signal Cable Pin Number 15-Pin Side of the Signal Cable
1 Video-Red 9 +5V
2 Video-Green 10 Ground
3 Video-Blue 11 N.C.
4 N.C. 12 DDC-Serial data
5 Detect Cable 13 H-sync
6 GND-R 14 V-sync
7 GND-G 15 DDC-Serial clock
8 GND-B
4.2 Factory Preset Display Modes
STAND RESOLUTION HORIZONTAL
FREQUENCY(kHz)
VERTICAL
FREQUENCY(Hz)
VGA 640×480 @60Hz DMT 31.469 59.94
VGA 640×480 @67Hz MAC 35 66.667
VGA 640×480 @72Hz DMT 37.861 72.809
VGA 640×480 @75Hz DMT 37.5 75
Dos-mode 720×400 @70Hz DOS 31.469 70.087
SVGA 800×600 @56Hz DMT 35.156 56.25
SVGA 800×600 @60Hz DMT 37.879 60.317
SVGA 800×600 @72Hz DMT 48.077 72.188
SVGA 800×600 @75Hz DMT 46.875 75
SVGA 832×624 @75Hz 49.725 74.55
XGA 1024×768 @60Hz DMT 48.363 60.004
XGA 1024×768 @70Hz DMT 56.476 70.069
XGA 1024×768 @75Hz DMT 60.023 75.029
WXGA 1366x768 @60Hz DMT 47.765 59.85

18.5" LCD Color Monitor AOC 936Swa
9
5. Panel Specification
5.1 Display Characteristics
M185B1-L02
M185XW01

18.5" LCD Color Monitor AOC 936Swa
10
LTM185AT02
5.2 Optical Characteristics
M185B1-L02

18.5" LCD Color Monitor AOC 936Swa
11
M185XW01

18.5" LCD Color Monitor AOC 936Swa
12
LTM185AT02

18.5" LCD Color Monitor AOC 936Swa
13
5.3 Parameter guide line for CCFL Inverter
1. TFT LCD Module
M185B1-L02
M185XW01
LTM185AT02

18.5" LCD Color Monitor AOC 936Swa
14
2. Backlight Unit
M185B1-L02
M185XW01
LTM185AT02

18.5" LCD Color Monitor AOC 936Swa
15
6. Block Diagram
6.1 Software Flow Chart
1
2
N
Y
5
Y
N
10
Y
N
12
Y
N
7
Y
N
6
4
3
8
9
14
11
13
Y
N
15
Y
N
16
17
19
Y
N
18

18.5" LCD Color Monitor AOC 936Swa
16
REMARK:
1) MCU initialize.
2) Is the EEprom blank?
3) Program the EEprom by default values.
4) Get the PWM value of brightness from EEprom.
5) Is the power key pressed?
6) Clear all global flags.
7) Are the AUTO and SELECT keys pressed?
8) Enter factory mode.
9) Save the power key status into EEprom.
Turn on the LED and set it to green color.
Scalar initialize.
10) In standby mode?
11) Update the lifetime of back light.
12) Check the analog port, are they’re any signals coming?
13) Does the scalar send out an interrupt request?
14) Wake up the scalar.
15) Are there any signals coming from analog port?
16) Display "No connection Check Signal Cable" message. And go into standby mode after the message
disappear.
17) Program the scalar to be able to show the coming mode.
18) Process the OSD display.
19) Read the keyboard. Is the power key pressed?

18.5" LCD Color Monitor AOC 936Swa
17
6.2 Electrical Block Diagram
6.2.1 Scalar Board
FLASH MEMORY
EN25F20-100GCP
(U402)
Scalar TSUM1PFR-LF
(Include :MCU,ADC,OSD etc)
(U401)
LCD Interface
(CN301)
D-Sub
Connector
(CN101)
H sync
V sync
RGB
EEPROM
AZC199-04S
(U103)
VGA_SDA,
VGA_SCL
Crystal 14.31818MHz
(X401)

18.5" LCD Color Monitor AOC 936Swa
18
6.2.2 Inverter / Power Board
CN902
DIM
EMI filter Bridge
Rectifier
and Filter
Start Circuit
PWM
Control IC
Transformer Rectifier
diodes
AC input
12V
ON/OFF
Control
PWM
Control IC
Feedback
Circuit
LC
Resonance
Transformer MOSFET
Over
Voltage
Lamp
ON/OFF
Feedback
Circuit
Over
Voltage
Protect 5V

18.5" LCD Color Monitor AOC 936Swa
19
7. Schematic
7.1 Main Board
715G3329 1 2
VCC 3.3
PA6
For BUZZER control board
or Touch Panel
DSUB_SOG2
MSD A
VPLL
DSUB_R-2
For NVRAM
NC
VCC3.3
BUZ ZER
U402
DSUB_G+2
020A
VCC3.3
Normal Function : CL = Cs + ((Cg*Cd)/(Cg+Cd))
CMVCC1
DDC1_SDA2
DSUB_B+2
R440 NC
PA1
PB6
PB1
R454 NC
R417 100R 1/16W 5%
C435
NC
FB401
300OHM
RXCN2
PPWR _ON#3
C436
1uF 10V
NC
RX1N2
EE_WP
C432
0.1 uF/ 16V
R457 N C
VCC1.84
RX0N2PB[0..9] 3
R462
NC
C408
0.1uF /16V
+
C419
10UF 50V
C409
0.1uF /16V
LED G_B
R427
NC
2.2K 1/16W 5%
DDC2_SDA2
VCC 3.32,4
C423
VCC 3.3
R409 100R 1/16W 5%
R404 1K 1/16W 5%
DDC2_SCL2
DSUB_V2
C406
0.1uF/16V
R424 100R 1/16W 5%
C405
0.1uF /16V
R442
PANEL_ID# 4
R432
3. 9K OHM +- 1% 1/ 16W
R447
NC
For user data, WB, EDID,
HDCP are saved in
Flash.
NC
RX2N2
DSUB_B-2
010A
DET_CABL E 2
LED O
R459
P.S : Assume Cs = 4 pF
X401
DSUB_G-2
R446
NC
VCC1.8
PA[0..9] 3
C401
0.22uF 16V
FB404
300OHM
C415
0.1uF /16V
R441
DVI 1_5V
CMVCC1 2
BUZZ ER
KEY1
R401 390 OHM 1/ 16W
U402
EN25F 20-100GCP
1
2
3
4 5
6
7
8
CS#
DO
WP#
VSS DI
CLK
HOLD#
VCC
RX1P2
HDCP_CTRL 2
LED_ORANGE
VCC 3.3
R441
NC
C421 47pF
For All model
RX0P2
Mut e 4
Eon
100R 1/16W 5%
27 pF
VDD P
VDDP
DDC1_SCL2
LED G_B
DDC_WP 2
PA0
PB2
U403
PA8
PA7
PB0
R460
NC
C420 47pF
100R 1/16W 5%
Indirect LED
adj_BACKLI GHT 4
Volume# 4
Q408
NC
CN 404
NC/CONN
1
2
3
4
5
6
NC
VDVI
MSC L
on_BACKLI GHT 4
CN402
CONN
1
2
3
4
5
6
7
X'TAL
NC
CL of SPEC
VCC3.3
PB3
C416
0.1uF 16V
R422
100R 1/16W 5 %
M24C04-WMN6TP
2.2K 1/16W 5%
VPLL
LED_GRN/BLUE
R442
NC
NC
SST
LED O
R457
R461
32 pF
R411 NC
C414
0.1uF /16V
CN401
NC/CONN
1
2
3
4
5
6
0.22uF16V
VCC3.3
PA5
R434
0R05 1/ 16W
Q408
CMVCC1
R433
3. 9K OHM +- 1% 1/ 16W
C417
0.1uF /16V
R440
NC
VCC3.3
LED_GRN/BLUE
R407
10K 1/16W 5%
Direct LED
PB5
R453 N C
R415 100R 1/16W 5%
C431
NC
0R 1/16W 5%
ZD 401
NC
AVDD
LF_B
EE_WP
2N3906S
VCC 3.3
KEY 2
C412
0.1uF /16V
C433
NC
VDVI
R405 0R05 1/10W 5%
Q407
NC
R462
18 pF
C434
NC
LF_B
C413
0.1uF /16V
NC
KEY1
PA2
R452 0R05 1/1 6W
2N3906S
MSC L
PA9
R419 0R05 1/16W
R461
0R05 1/ 10W 5%
Q401
LMBT3904LT1G
R416 100R 1/16W 5%
Q405
2N3906S-R TK/PS
1
23
WP
MSD A
C402
4.7uF /10V
Max condition for LED:
1. Vcc = 3.3 V
2. Current = 12 mA
FW need to be
modified.
VDDC
PB8
PB9
R406
22K 1/16W 5%
R412
10K 1/16W 5%
CN405
NC/CONN
1
2
3
4
5
6
7
Eon
R453
VCC3.3
R456
22 OHM 1/ 10W
U403
NC
1
2
3
45
6
7
8NC
E1
E2
VSSSD A
SCL
WC
VCC
R414
0R05 1/1 6W
AOC 936SWA B
NEW R SERIES Custom
55Tuesday , May 12, 2009
<
称爹 >
5.0.SCALER
G3329-1-2-X-1-090512
OEM MODEL Size
Rev
Date Sheet of
TPV MOD EL
PCB N AME
称爹
T P V ( Top Victory Electronics Co . , Ltd. )
Key Component
絬 隔 瓜 絪 腹
CMVCC1
020
CMVCC1
Cs and Cd (C420, C421)
X401
14.31818MHz
1 2
PB[0..9]
For ID2008 ID2009
R419
VDDC
NC
C404
0.1uF /16V
U402
NC
Befor AOC ID2007 OSD
10K 1/16W 5%
AVDD
R445 N C
POWER_KEY#
TOUCH_POWER
C411
0.1uF /16V
C407
0.1uF /16V
U402
10K 1/16W 5%
Q407
R455
10K 1/16W 5%
C438
NC
Without NVRAM
NC
POWER _KEY #
CMVCC1
R436
10K 1/16W 5%
100R 1/16W 5%
C422 0. 1uF/16V
FB402
300OHM
PB4
56 pF
R402
1K 1/16W 5%
NC
R459 NC
R423
0R05 1/1 6W
PA[0..9]
C403
0.1uF /16V
R420 N C
R430
R429 NC
R430 NC
R421
100K 1/16W 5%
VMPLL
VCC 3.3
R426 NC
R429
NC
AVDD
VMPLL
LED_ORANGE
PA4
LVDS
CN 403
NC/CONN
2
4
6
8
1
3
5
7
For detect function,
depend on FW
KEY2
R428 100R 1/16W 5%
R418
0R05 1/ 16W
C423
NC
R420
CN406
NC/CONN
1
2
3
TSUM1PFL-LF
23
20
21
18
22
19
17
27
28
15
26
25
37
39
38
40
47
86
59
96
97
60
61
62
63
64
65
67
68
69
70
71
72
73
74
77
78
58
55
54
2 5
3
4
6
7
8
9
10
12
13
11 29 33
24 56
53
52
81
51
30
31
100
1
93
14 75
35
48
85
88
89
90
91
92
94
95
99
43
44
84
41
42
98 16 32 49 66 82 34
50 57 76 79 83
80
87
36
45
46
RIN0P
GIN0P
SOGIN0
BIN0P
RIN0M
GIN0M
BIN0M
HSYNC0
VSYNC 0
REXT
REFP
REFM
SDO
SCK
SCZ
SDI
PWM2/GPIO_P24
PWM1/GPIO_P25
LVACKM
XI N
XO U T
LVA2P
LVA2M
LVA1P
LVA1M
LVA0P
LVA0M
LVB3P
LVB3M
LVBCKP
LVBCKM
LVB2P
LVB2M
LVB1P
LVB1M
LVB0P
LVB0M
LVACKP
LVA3M
LVA3P
GND GND
NC
NC
NC
NC
AVDD_ 33
NC
NC
NC
NC
GND GND GND
AVDD_ 33
VDDP
MOD E[1 ]
MOD E[0 ]
VCTRL
VDDC
DDCA_SDA/RS232_TX
DD CA_SCL/r s232_RX
NC
NC
PWM0/GPIO_P26
AVDD_ 33
VDDP
GPIO_P22/ PWM0
GPIO_P27/PWM1
GPIO_P12
GPIO_P00/ SAR1
GPIO_P01/ SAR2
GPIO_P02/ SAR3
GPIO_P06
GPIO_P07
GPIO_P13
GPIO_P14
GPIO_P16/ PWM2
GPIO_P11/I2C_MDA
GPIO_P10/ I2C_MCL
RST
GPIO_P23
GPIO_P22
AVDD_ 33 AVDD_ 33
VDDP VDDP
VDDC VDDC VDDC
GND GND GND GND GND
BYPASS
GPIO_P17/ SAR0
GPIO_P40
GPIO_P41
GPIO_P42
瑉红 (93G 22-53-J)
100R 1/16W 5%
10K 1/16W 5%
0R 1/16W 5%
R451 NC
R435
NC
PA3
R431
NC
R408 NC
R425 N C
R455 N C
NC
WP
SST
NC
CMVCC1
RXCP2
DSUB_H2
DSUB_R+2
FB405
NC
PB7
蔼 (93G 22-53B-H)
VCC3.3
RX2P2
R458 NC
C410
0.1uF /16V
10K 1/16W 5%
0R 1/16W 5%
0R 1/16W 5%

18.5" LCD Color Monitor AOC 936Swa
20
VGA_B+
VGA_G-
C101
NC
DGND
DVI_5V
DSUB_V 5
VGA_PLUG
C118
NC
R133
10K 1/16W 5%
R131 NC
DSUB_SOG 5
R107
2K2 1/16W 5%
AOC 936SWA B
NEW R SERIES B
25Tuesday , May 12, 2009
<
称爹 >
2.0.INPUT
G3329-1-2-X-1-090512
OEM MODEL Size
Rev
Date Sheet of
TPV MOD EL
PCB NAME
称爹
T P V ( Top Victory Electronics Co . , Ltd. )
Key Component
絬 隔 瓜 絪 腹
CN102
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
26 25
DAT2-
DAT2+
2/4shield
DAT4-
DAT4+
DDC SCL
DDC SDA
VSYNC
DAT1-
DAT1+
1/3shield
DAT3-
DAT3+
+5V
SYNC GND
HPD
DAT0-
DAT0+
0/5shield
DAT5-
DAT5+
clk shield
clk+
clk-
GND GND
C115
0.1uF/16V
R130 NC
U105
NC
1
2
3 4
5
6
I/O1
GND
I/O2 I/O3
VDD
I/O4
ESD_VCC1
C120
NC
R135
NC
R138
NC
H_Sync
DDC1_SCL
DDC2_SCL 5
R121
NC
R120 NC
R117
100R 1/16W 5%
RX0N
ESD_VCC1
R136
NC
C113
5pF/50V
ZD104
RLZ5.6B
VCC3.3
DSUB_G- 5
R108
75R 1/16W 5%
VGA_G+
U106
NC
1
2
3 4
5
6
I/O1
GND
I/O2 I/O3
VDD
I/O4
C107
1000pF
DSUB_H 5
VGA_G-
VGA_R-
R104 1K 1/16W 5%
R119 NC
CMVCC1
U101
AT24C02BN-SH-T
1
2
3
45
6
7
8A0
A1
A2
GNDSDA
SCL
WP
VCC
VGA_PLUG
H_Sync
R103 1K 1/16W 5%
VGA_B+
DVI 1_5V
RXCN 5
Q101
NC
CN101
1
6
2
7
3
8
4
9
5
11
12
13
14
15
10
17 16
R137
NC
R102 0R05 1/10W 5%
R116
75R 1/16W 5%
CMVCC1
DDC1_SCL
C117
NC
DDC2_SDA
C111
0.047uF
C122
NC
C105
5pF/50V
DSUB_R+ 5
DET_CABLE 5
ESD_VCC
DDC1_SDA
R114
100R 1/16W 5%
DSUB_5V
DSUB_SDA
FB105
NC
R139
6K8 1/16W 5%
R127 NC
VGA_PLUG
R126 NC
R134 NC
候綼 U105
ESD_VCC1
DSUB_5V
VGA_R+
FB103
BEAD
1 2 R111
100R 1/16W 5%
R101
100R 1/16W 5%
R110
470R 1/16W 5%
C110
0.047uF
C106
0.047uF
候綼 U106
RX1N 5
RX2N
R123
4K7 1/16W 5%
U103
AZC199-04S
1
2
3 4
5
6
I/O1
GND
I/O2 I/O3
VDD
I/O4
R132 NC
FB102
BEAD
1 2
RXCN
DDC2_SCL
候綼 U107
C104
22pF
DDC_WP5
V_Sy nc
C109
5pF/50V
RX1P
C124
0.1uF/16V
候綼 U103
DSUB_SCL
DDC1_SDA
DDC2_SDA
DSUB_SDA
C116
0.22uF16V
C112
NC
DSUB_B+ 5
R129 NC
DSUB_B- 5
RX1N
FB104
NC
ESD_VCC1
DSUB_R- 5
U102
NC
1
2
3
45
6
7
8A0
A1
A2
GNDSDA
SCL
WP
VCC
R112
75R 1/16W 5%
R118 NC
DVI_HPD
VGA_B+
DDC2_SCL
R113
100R 1/16W 5%
RXCP
U104
AZC199-04S
1
2
3 4
5
6
I/O1
GND
I/O2 I/O3
VDD
I/O4
ESD_VCC
RX0P 5
RX0N 5
ESD_VCC
RX2P 5
VGA_R+
VGA_B-
R140
NC
DSUB_G+ 5
VGA_G+
R105
100R 1/16W 5%
DVI_5V
U107
NC
1
2
3 4
5
6
I/O1
GND
I/O2 I/O3
VDD
I/O4
HDCP_CTRL 5
DDC_WP5
DDC1_SDA5
RX2N 5
GND POWER
VGA_R-
RXCP 5
D104
BAV70
3
1 2
R109
100R 1/16W 5%
D108
NC
3
1 2
DVI_HPD
VGA_G+
RX2P
FB101
BEAD
1 2
DSUB_SCL
VGA_B-
C103
22pF
R122
NC
RX1P 5
C108
0.047uF
C114
0.047uF
C102
0.047uF
DDC2_SDA 5
RX0P
R128 NC
C121
NC
R124
4K7 1/16W 5%
CMVCC13,4
候綼 U101
DVI 1_5V
VGA_R+
R125
4K7 1/16W 5%
DDC1_SCL5
R106
2K2 1/16W 5%
V_Sy nc
C119
NC
R115
100R 1/16W 5%