AOC AG271FZ2 User manual

LCD Monitor User Manual
AG271FZ2 LED backlight
www.aoc.com
©2019 AOC. All Rights Reserved.

2
Safety........................................................................................................................................................................3
National Conventions.........................................................................................................................................3
Power ................................................................................................................................................................4
Installation..........................................................................................................................................................5
Cleaning.............................................................................................................................................................6
Other..................................................................................................................................................................7
Setup ........................................................................................................................................................................8
Contents in Box .................................................................................................................................................8
Setup Stand & Base...........................................................................................................................................9
Adjusting Viewing Angle...................................................................................................................................10
Connecting the Monitor....................................................................................................................................11
Adaptive-Sync function....................................................................................................................................12
Wall Mounting..................................................................................................................................................13
Adjusting.................................................................................................................................................................14
Hotkeys............................................................................................................................................................14
Quick Switch....................................................................................................................................................15
OSD Setting.....................................................................................................................................................16
Luminance................................................................................................................................................17
Image Setup.............................................................................................................................................18
Color Setup...............................................................................................................................................19
Picture Boost............................................................................................................................................20
OSD Setup ...............................................................................................................................................21
Game Setting............................................................................................................................................22
Extra.........................................................................................................................................................23
Exit............................................................................................................................................................24
LED Indicator...................................................................................................................................................24
Driver......................................................................................................................................................................25
G-Menu............................................................................................................................................................25
e-Saver............................................................................................................................................................26
Screen+...........................................................................................................................................................27
Troubleshoot...........................................................................................................................................................28
Specification............................................................................................................................................................29
General Specification.......................................................................................................................................29
Preset Display Modes......................................................................................................................................30
Pin Assignments ..............................................................................................................................................31
Plug and Play...................................................................................................................................................33

3
Safety
National Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type.
These blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer system.
CAUTION: ACAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: AWARNING indicates the potential for bodily harm and tells you how to avoid the problem.Some
warnings may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specific
presentation of the warning is mandated by regulatory authority.

4
Power
The monitor should be operated only from the type of power source indicated on the label. If you are not sure
of the type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will
fit only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug,
have an electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the
safety purpose of the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the
monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in fire or electric shock.
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate
configured receptacles marked between 100 - 240V ~, Min. 5A
The wall socket shall be installed near the equipment and shall be easily accessible.
For use only with the attached power adapter (Output: 20Vdc, 4.5A)
Manufacturers: TPV ELECTRONICS（FUJIAN）CO.,LTD. Model: ADPC2090

5
Installation
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a
person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by
the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and
use mounting accessories recommended by the manufacturer. A product and cart combination should be moved
with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a fire or
electric shock. Never spill liquids on the monitor.
Do not place the front of the product on the floor.
If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
instructions.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence
overheating may cause a fire or damage to the monitor.
See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on
the stand:
Installed on the wall
Installed with stand
Leave at lease this space
around the set
10cm
4 inches
10cm
4 inches
11 7/8 inches
10cm
4 inches
30cm
10cm
4 inches
10cm
4 inches
11 7/8 inches
30cm
10cm
4 inches
Leave at lease this space
around the set

6
Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of
strong-detergent which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough
as it will scratch the screen surface.
Please disconnect the power cord before cleaning the product.

7
Other
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and
contact a Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.

8
Setup
Contents in Box
Not all signal cables (Audio, Analog, DVI, USB, DP and HDMI cables) will be provided for all countries and
regions. Please check with the local dealer or AOC branch office for confirmation.
CD manual Warranty card Stand Base Quick Switch Keypad VESA bracket
Adapter Power Cable Audio Cable Dual-Link Analog cable DP cable HDMI cable USB cable
DVI Cable
Monitor

9
Setup Stand & Base
Please setup or remove the base following the steps as below.
Setup:
Remove:

10
Adjusting Viewing Angle
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your
own preference.
Hold the stand so you will not topple the monitor when you change the monitor's angle.
You are able to adjust the monitor as below:
Tilt angle:- 5°~23°Pivot angle: 0°~90°
Swivel angle: -20°~20°Height adjustment:130mm
NOTE:
1. Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
2. The scale on the stand can remember which location is your favorite.

11
Connecting the Monitor
Cable Connections In Back of Monitor and Computer:
1
Power
9
Quick Switch port
2
DVI Dual-Link
10
Microphone in
3
HDMI-2(HDMI1.4)
11
Earphone( Combined with Microphone)
4
HDMI-1(HDMI2.0)
12
USB3.0 downstream + fast charging
5
DP
13
USB3.0 downstream
6
D-SUB
14
USB3.0 upstream
7
Audio line in
15
Headphone hook
8
Microphone out
To protect equipment, always turn off the PC and LCD monitor before connecting.
1 Connect the power cable to the DC port on the back of the monitor.
2 Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the
computer's D-Sub port.
3 (Optional –Requires a video card with DVI port) - Connect one end of the DVI cable to the back of the monitor
and connect the other end to the computer’s DVI port.
4 (Optional –Requires a video card with HDMI port) - Connect one end of the HDMI cable to the back of the
monitor and connect the other end to the computer’s HDMI port.
5 (Optional –Requires a video card with Audio port) - Connect one end of the Audio cable to the back of the
monitor and connect the other end to the computer’s Audio port.
6 (Optional–Requires a video card with DP port) –Connect one end of the DP cable to the back of the monitor
and connect the other end to the computer’s DP port.
7 Turn on your monitor and computer.
If your monitor displays an image, installation is complete. If it does not display an image, please refer
Troubleshooting.

12
Adaptive-Sync function
1. Adaptive-Sync function is working with DP/HDMI
2. Compatible Graphics Card: Recommend list is as the below, also could be checked by visiting
www.AMD.com
RadeonTM RX Vega Series
RadeonTM RX 500 Series
RadeonTM RX 400 Series
RadeonTM R9/R7 300 Series（except R9 370/X，R7 370/X，R7 265）
RadeonTM Pro Duo（2016 Version）
RadeonTM R9 Nano Series
RadeonTM R9 Fury Series
RadeonTM R9/R7 200 Series（except R9 270/X，R9 280/X）

13
Wall Mounting
Preparing to Install An Optional Wall Mounting Arm.
This monitor can be attached to a wall mounting arm you purchase separately. Disconnect power before this
procedure. Follow these steps:
1 Remove the base.
2 Follow the manufacturer's instructions to assemble the wall mounting arm.
3 Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the
back of the monitor.
4 Insert the 4 screws into the holes and tighten.
5 Reconnect the cables. Refer to the user's manual that came with the optional wall mounting arm for
instructions on attaching it to the wall.
Noted : VESA mounting screw holes are not available for all models, please check with the dealer or official
department of AOC.

14
Adjusting
Hotkeys
1
Source/Auto/Exit
2
Game Mode/<
3
Dial Point />
4
Menu/Enter
5
Power
Power
Press the Power button to turn on/off the monitor.
Menu/Enter
Press to display the OSD or confirm the selection.
Dial Point/>
When there is no OSD, press Dial Point button to show / hide Dial Point.
Game Mode/<
When there is no OSD, press the minus key to open game mode function, then press < or > key to select game
mode (FPS, RTS, Racing, Gamer 1, Gamer 2 or Gamer 3) basing on the different game types.
Source/Auto/Exit
When there is no OSD, press Auto/Source button continuously about 2 second to do auto configure. When the
OSD is closed, press Source button will be Source hot key function. Press Source button continuously to select the
input source showed in the message bar, press Menu/Enter button to change to the source selected.

15
Quick Switch
◀:
When there is no OSD, press the ◀button to open game mode function, then press ◀or ▶key to select game
mode (FPS, RTS, Racing, Gamer 1, Gamer 2 or Gamer 3) basing on the different game types.
▶:
When there is no OSD, press ▶button to show / hide Dial Point.
Menu:
Press the Menu button to display the menu
OK:
Press the OK button to confirm the selection.
:
Press the button to exit.
When there is no OSD, press continuously about 2 second to do auto configure. When the OSD is closed,
press button will be Source hot key function. Press button continuously to select the input source showed
in the message bar, press OK button to change to the source selected.
1:
Press the 1 button to select Gamer 1 mode
2:
Press the 2 button to select Gamer 2 mode
3:
Press the 3 button to select Gamer 3 mode

16
OSD Setting
Basic and simple instruction on the control keys.
1) Press the -button to activate the OSD window.
2) Press < or > to navigate through the functions. Once the desired function is highlighted, press the -button
to activate it . press < or > to navigate through the sub-menu functions. Once the desired function is highlighted,
press -button to activate it.
3) Press < or > to change the settings of the selected function. Press to exit. If you want to adjust any other
function, repeat steps 2-3.
4) OSD Lock Function: To lock the OSD, press and hold the button while the monitor is off and then press
button to turn the monitor on. To un-lock the OSD - press and hold the button while the monitor is off
and then press button to turn the monitor on.
Notes:
1) If the product has only one signal input, the item of "Input Select" is disable to adjust.
2) ECO modes (except Standard mode), DCR, DCB mode and Picture Boost, for these four states that only one
state can exist.

17
Luminance
1. Press (Menu) to display menu.
2. Press< or >to select (Luminance), and press to enter.
3. Press< or >to select submenu, and press to enter.
4. Press< or >to adjust.
5. Press to exit.
Contrast
0-100
Contrast from Digital-register.
Brightness
0-100
Backlight Adjustment
Eco mode
Standard
Standard Mode
Text
Text Mode
Internet
Internet Mode
Game
Game Mode
Movie
Movie Mode
Sports
Sports Mode
Reading
Reading Mode
Gamma
Gamma1
Adjust to Gamma1
Gamma2
Adjust to Gamma 2
Gamma3
Adjust to Gamma 3
DCR
Off
Disable dynamic contrast ratio
On
Enable dynamic contrast ratio

18
Image Setup
1. Press (Menu) to display menu.
2. Press< or >to select (Image Setup), and press to enter.
3. Press< or >to select submenu, and press to enter.
4. Press< or >to adjust.
5. Press to exit.
Clock
0-100
Adjust picture Clock to reduce Vertical-Line noise.
Phase
0-100
Adjust Picture Phase to reduce Horizontal-Line noise
Sharpness
0-100
Adjust picture sharpness
H. Position
0-100
Adjust the horizontal position of the picture.
V. Position
0-100
Adjust the vertical position of the picture.

19
Color Setup
1. Press (Menu) to display menu.
2. Press< or >to select (Color Setup), and press to enter.
3. Press< or >to select submenu, and press to enter.
4. Press< or >to adjust.
5. Press to exit.
Color Temp.
Warm
Recall Warm Color Temperature from EEPROM.
Normal
Recall Normal Color Temperature from EEPROM.
Cool
Recall Cool Color Temperature from EEPROM.
sRGB
Recall SRGB Color Temperature from EEPROM.
User
Red
Red Gain from Digital-register
Green
Green Gain Digital-register.
Blue
Blue Gain from Digital-register
DCB Mode
Off
Disable DCB Mode
Full Enhance
Enable Full Enhance Mode
Nature Skin
Enable Nature Skin Mode
Green Field
Enable Green Field Mode
Sky-blue
Enable Sky-blue Mode
AutoDetect
Enable AutoDetect Mode
DCB Demo
On/Off
Disable or Enable Demo

20
Picture Boost
1. Press (Menu) to display menu.
2. Press< or >to select (Picture Boost), and press to enter.
3. Press< or >to select submenu, and press to enter.
4. Press< or >to adjust.
5. Press to exit.
Bright Frame
on or off
Disable or Enable Bright Frame
Frame Size
14-100
Adjust Frame Size
Brightness
0-100
Adjust Frame Brightness
Contrast
0-100
Adjust Frame Contrast
H. Position
0-100
Adjust Frame horizontal Position
V. Position
0-100
Adjust Frame vertical Position
Note:
Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience.