AOC e2352Phz User manual

23"LCDColorMonitor AOC E2352PHZ
Service
Service
Service
Horizontal Frequency
30-83 KHz
Table of Contents
Description Page Description Page
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
Table of Contents.......……..............................……........1
Revision List.…........................................…………........2
Important Safety Notice.……............................……......3
1.Monitor Specification..............................………..........4
2.LCD Monitor Description……………………………......5
3.Operation Instruction…………...............……..............6
3.1.General Instructions...........................…...................6
3.2.Control Button…………….…..............……...............6
3.3.OSD Menu…………….…...........................…...........7
4.Input/Output Specification............……………............22
4.1.Input Signal Connector............………….................22
4.2.Factory Preset Display Modes…….........................24
4.3.Panel Specification.....………...…………................25
5.Block Diagram…….....................………….................27
5.1.Main Board…….…………...………………....….......27
5.2.Power Board……………..……………...….......28
6.Schematic……………........................................29
6.1.Main Board………...........................................29
6.2.Power Board...…….........................................35
6.3.Key Board...…….............................................37
7.PCB Layout..………….......................................38
7.1.Main Board………...........................................38
7.2.Power Board…...............................................40
7.3.Key Board…………….....................................43
8.Maintainability……….........................................44
8.1.Equipments and Tools Requirement...............44
8.2.Trouble Shooting…………..............................45
9.White-Balance, Luminance Adjustment.............49
10.Monitor Exploded View………..…….…............51
11.BOM List…………………………………............53
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING

2
Revision List
Version Release Date Revision History TPV Model Name
A00 Jul.5.2011 Initial release
HDBGT22MAYSCDN
HDBGT22LAY3ADN
HDBGT22FAYUHDN
HDBGT22BAYK2DN
HDBGT22TAY1RDN
A01 Nov.08.2011 Add new model HDBGT22AAYUNDN
A02 Nov.21.2011 Add new models
HDBGT22EAYACDN
HDBGT22EAY6ADN
HDBGT22QAYA6DN
HDBGT22KAYE6DN

3
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiation when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)

4
1. Monitor Specifications

5
2. LCD Monitor Description
The LCD monitor will contain a main board, an adapter board, a converter board and a key board which house the
flat panel control logic, brightness control logic and DDC.
The power part will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each
voltage.
AC-IN
100V-240
Monitor Block Diagram
Adapter Board
Flat Panel and backlight
Main Board
RS232 Connector
For white balance
adjustment in factory
mode
Video signal, DDC
Key Board
Host Computer
Converter Board

6
3. Operating Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor.
By changing these settings, the picture can be adjusted to your personal preferences.
3.2 Control Buttons
Power
Press the Power button to turn on/off the monitor.
3D/-
Press this hotkey continuously to select 2D/3D functions when the on-screen display (OSD) is unavailable.
Volume/+
When there is no OSD, press Volume adjust volume.
Auto / Exit / Source hot key
When there is no OSD, press Auto/Source button continuously about 2 second to do auto configure. When the OSD
is closed, press Source button will be Source hot key function. Press Source button continuously to select the input
source showed in the message bar, press Menu/Enter button to change to the source selected.

7
3.3 OSD Menu
1) Press the MENU-button to activate the OSD window.
2) Press - or + to navigate through the functions. Once the desired function is highlighted, press the MENU-button
to activate it. Press - or + to navigate through the sub-menu functions. Once the desired function is highlighted,
press MENU-button to activate it.
3) Press - or + to change the settings of the selected function. Press AUTO to exit. If you want to adjust any other
function, repeat steps 2-3.
4) OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press
power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off
and then press power button to turn the monitor on.
Notes:
1) If the product has only one signal input, the item of "Input Select" is disable to adjust.
2) If the product screen size is 4:3 or input signal resolution is wide format, the item of "Image Ratio" is disable to
adjust.
3) One of DCR, Color Boost, and Picture Boost functions is active, the other two function is turned off accordingly.

8

9

10

11

12

13

14

15

16

17

18

19

20