AOC E2495SD User manual

24" LCD Color Monitor AOC E2495SD
Copyright © 2012 by TPV Corporation. All rights reserved. Specifications are subject to change without notice.
No part of this publication may be reproduced in any form or means, without the prior written permission of TPV Corporation. Otherwise we will
reserve the right to investigate the legal responsibility.
1
Service
Service
Service
HorizontalFrequency
30-83kHz
TABLE OF CONTENTS
Description Page Description Page
SAFETY NOTICE
ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS
AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING
ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES.
Table Of Contents…………………………………………...1
Revision List………………………………………………....2
Important Safety Notice ……..............................……...... 3
1. Monitor Specification..............................…………........4
2. LCD Monitor Description…………………………….......5
3. Operation Instructions....................................…...........6
3.1. General Instructions..........................….....................6
3.2. Control Buttons………………………….…................6
3.3 Adjusting the Picture...................................................8
4. Input/ Output Specification............……………............14
4.1. Input Signal Connector..............……….................14
4.2. Factory Preset Display Modes...........…..................15
4.3. Panel Specification......……..…………..................16
5. Block Diagram….........................................................19
5.1 Main Board……………………………………….…….19
5.2.Power Board……………………………………….......20
6. Schematic……………..............................................21
6.1. Main Board....………............................................21
6.2. Power Board……………………………………....26
6.3. Key Board………………...….……………………28
7. PCB Layout..………….............................................29
7.1. Main Board………................................................29
7.2. Power Board.…....................................................32
7.3. Key Board….........................................................35
8. Maintainability………...............................................36
8.1. Equipments and Tools Requirement.....................36
8.2. Trouble Shooting……….......................................37
9. White-Balance, Luminance Adjustment….…..…...41
10. Monitor Exploded View………….……….…........43
11. BOM List…............................................................45
CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING

24" LCD Color Monitor AOC E2495SD
2
Revision List
Version Release Date Revision History TPV Model Name
A00 Dec.12, 2012 Initial release TKCAUF7BALK2HN

24" LCD Color Monitor AOC E2495SD
3
Important Safety Notice
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service
procedures recommended by AOC and described in this service manual are effective methods of performing service
operations. Some of these service operations require the use of tools specially designed for the purpose. The
special tools should be used when and as recommended.
It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in
order to minimize the risk of personal injury to service personnel. The possibility exists that improper service
methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE
NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in
which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not
undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not
recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the
equipment will be jeopardized by the service method selected.
Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock,
fire, or other hazards.
Under no circumstances should the original design be modified or altered without written permission from AOC.
AOC assumes no liability, express or implied, arising out of any unauthorized modification of design.
Servicer assumes all liability.
FOR PRODUCTS CONTAINING LASER:
DANGER-Invisible laser radiation when open AVOID DIRECT EXPOSURE TO BEAM.
CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
CAUTION -The use of optical instruments with this product will increase eye hazard.
TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S
REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF
THIS SERVICE MANUAL.
Take care during handling the LCD module with backlight unit
-Must mount the module using mounting holes arranged in four corners.
-Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen.
-Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to
the panel.
-Protect the module from the ESD as it may damage the electronic circuit (C-MOS).
-Make certain that treatment person’s body is grounded through wristband.
-Do not leave the module in high temperature and in areas of high humidity for a long time.
-Avoid contact with water as it may a short circuit within the module.
-If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may
damage the panel.)

24"LCDColorMonitor AOCE2495SD
4
1. Monitor Specification

24"LCDColorMonitor AOCE2495SD
5
2. LCD Monitor Description
The LCD Monitor will contain a main board, a power board and a key board which house the flat panel control logic,
brightnesscontrollogicandDDC.
The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips
each voltage.
Video signal, DDC
Power Board
Flat Panel and
LED backlight
Main Board RS232 Connector
For white balance
adjustment in
factory mode
HOST Computer
Led Drive
AC-IN
100V~240V
Monitor Block Diagram
Key board

24"LCDColorMonitor AOCE2495SD
6
3. Operation Instructions
3.1 General Instructions
Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the
monitor. By changing these settings, the picture can be adjusted to your personal preferences.
The power cord should be connected.
Connect the Signal cable from the monitor to the video card.
Press the power button to turn on the monitor position. The power indicator will light up.
3.2 Control Buttons
EXTERNAL CONTROLS
Power
Press the Power button to turn on/off the monitor.
Eco (DCR/I-Care)/-
Press the Eco key continuously to select the Eco mode of brightness and DCR/I-Care on when there is no OSD.
(Eco mode hot key may not be available in all models).
Volume / +
When there is no OSD, Press Volume button to active volume adjustment bar, Press -or + to adjust volume (Only
for the models with speakers).
4:3 or Wide/+
When there is no OSD, press + continuously to change 4:3 or wide image ratio. (If the product screen size is 4:3 or
input signal resolution is wide format, the hot key is disable to adjust. )
Auto / Exit
When there is no OSD, press Auto/ Source button continuously about 3 second to do auto configure.
Source hot key
When the OSD is closed, press Source button will be Source hot key function. Press Source button continuously to
select the input source showed in the message bar, press Menu/Enter button to change to the source selected.

24"LCDColorMonitor AOCE2495SD
7
FRONT PANEL CONTROL
1) Press the MENU-button to activate the OSD window.
2) Press - or + to navigate through the functions. Once the desired function is highlighted, press the MENU-button
to activate it . press - or + to navigate through the sub-menu functions. Once the desired function is highlighted,
press MENU-button to activate it.
3) Press - or + to change the settings of the selected function. Press AUTO to exit. If you want to adjust any other
function, repeat steps 2-3.
4) OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press
power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off
and then press power button to turn the monitor on.
Notes:
1) If the product has only one signal input, the item of "Input Select" is disable to adjust.
2) If the product screen size is 4:3 or input signal resolution is wide format, the item of "Image Ratio" is disable to
adjust.
3) One of DCR, Color Boost, and Picture Boost functions is active, the other two function is turned off accordingly.

24"LCDColorMonitor AOCE2495SD
8
3.3 Adjusting the Picture
HOW TO ADJUST A SETTING

24"LCDColorMonitor AOCE2495SD
9

24"LCDColorMonitor AOCE2495SD
10