AOC U2790PC User manual
1
www.aoc.com
©2021 AOC.All Rights Reserved
LCD Monitor
User Manual
U2790PC
i
Safety ................................................................................................................................................................................... 1
National Conventions ................................................................................................................................................ 1
Power ........................................................................................................................................................................ 2
Installation ................................................................................................................................................................. 3
Cleaning .................................................................................................................................................................... 4
Other ......................................................................................................................................................................... 5
Setup .................................................................................................................................................................................... 6
Contents in Box......................................................................................................................................................... 6
Setup Stand & Base.................................................................................................................................................. 7
Adjusting Viewing Angle............................................................................................................................................ 8
Connecting the Monitor ............................................................................................................................................. 9
Adjusting............................................................................................................................................................................. 10
Hotkeys ................................................................................................................................................................... 10
OSD Setting ............................................................................................................................................................ 12
Luminance ................................................................................................................................................... 13
Color Setup.................................................................................................................................................. 14
Picture Boost ............................................................................................................................................... 15
OSD Setup................................................................................................................................................... 16
Extra ............................................................................................................................................................ 17
Exit............................................................................................................................................................... 18
LED Indicator .......................................................................................................................................................... 19
Troubleshoot....................................................................................................................................................................... 20
Specication ....................................................................................................................................................................... 21
General Specication .............................................................................................................................................. 21
Preset Display Modes ............................................................................................................................................. 22
Pin Assignments...................................................................................................................................................... 23
Plug and Play .......................................................................................................................................................... 24
1
Safety
National Conventions
The following subsections describe notational conventions used in this document.
Notes, Cautions, and Warnings
Throughout this guide, blocks of text may be accompanied by an icon and printed in bold type or in italic type. These
blocks are notes, cautions, and warnings, and they are used as follows:
NOTE: A NOTE indicates important information that helps you make better use of your computer system.
CAUTION: A CAUTION indicates either potential damage to hardware or loss of data and tells you how to avoid the
problem.
WARNING: A WARNING indicates the potential for bodily harm and tells you how to avoid the problem. Some warnings
may appear in alternate formats and may be unaccompanied by an icon. In such cases, the specic presentation of the
warning is mandated by regulatory authority.
2
Power
The monitor should be operated only from the type of power source indicated on the label. If you are not sure of the
type of power supplied to your home, consult your dealer or local power company.
The monitor is equipped with a three-pronged grounded plug, a plug with a third (grounding) pin. This plug will t
only into a grounded power outlet as a safety feature. If your outlet does not accommodate the three-wire plug, have an
electrician install the correct outlet, or use an adapter to ground the appliance safely. Do not defeat the safety purpose of
the grounded plug.
Unplug the unit during a lightning storm or when it will not be used for long periods of time. This will protect the
monitor from damage due to power surges.
Do not overload power strips and extension cords. Overloading can result in re or electric shock.
To ensure satisfactory operation, use the monitor only with UL listed computers which have appropriate congured
receptacles marked between 100-240V AC, Min. 1.5A.
The wall socket shall be installed near the equipment and shall be easily accessible.
For use only with the attached power adapter
Manufacturers: TPV ELECTRONICS(FUJIAN)CO.,LTD. Model: ADPC2090
3
Installation
Do not place the monitor on an unstable cart, stand, tripod, bracket, or table. If the monitor falls, it can injure a
person and cause serious damage to this product. Use only a cart, stand, tripod, bracket, or table recommended by
the manufacturer or sold with this product. Follow the manufacturer’s instructions when installing the product and use
mounting accessories recommended by the manufacturer. A product and cart combination should be moved with care.
Never push any object into the slot on the monitor cabinet. It could damage circuit parts causing a re or electric
shock. Never spill liquids on the monitor.
Do not place the front of the product on the oor.
If you mount the monitor on a wall or shelf, use a mounting kit approved by the manufacturer and follow the kit
instructions.
Leave some space around the monitor as shown below. Otherwise, air-circulation may be inadequate hence
overheating may cause a re or damage to the monitor.
See below the recommended ventilation areas around the monitor when the monitor is installed on the wall or on the
stand:
Installed with stand
Installed with stand
12 inches
30cm
4 inches
10cm
4 inches
10cm
4 inches
10cm
Leave at lease this
space around the set
Please purchase a suitable wall mount to avoid the lack of distance between the back signal cable and the wall.
4
Cleaning
Clean the cabinet regularly with cloth. You can use soft-detergent to wipe out the stain, instead of strong-detergent
which will cauterize the product cabinet.
When cleaning, make sure no detergent is leaked into the product. The cleaning cloth should not be too rough as it
will scratch the screen surface.
Please disconnect the power cord before cleaning the product.
5
Other
If the product is emitting a strange smell, sound or smoke, disconnect the power plug IMMEDIATELY and contact a
Service Center.
Make sure that the ventilating openings are not blocked by a table or curtain.
Do not engage the LCD monitor in severe vibration or high impact conditions during operation.
Do not knock or drop the monitor during operation or transportation.
6
Setup
Contents in Box
Monitor
CD Manual
Warranty Card
Base
Stand
Power Cord
Adapter
HDMI Cable
USB Cable
USB C-C Cable
DP Cable
*
*
*
**
Not all signal cables will be provided for all countries and regions. Please check with the local dealer or AOC branch
oce for conrmation.
7
Setup Stand & Base
Please setup or remove the base following the steps as below.
Setup:
Remove:
8
Adjusting Viewing Angle
For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own
preference.
Hold the stand so you will not topple the monitor when you change the monitor’s angle.
You are able to adjust the monitor as below:
NOTE:
Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen.
9
Connecting the Monitor
Cable Connections In Back of Monitor and Computer:
321 4 5 6 7 8
1. Power
2. HDMI-1
3. HDMI-2
4. DP
5. USB C
6. USB up
7. USB3.2 Gen1x2
8. Earphone
Connect to PC
1. Connect the power cord to the back of the display rmly.
2. Turn o your computer and unplug its power cable.
3. Connect the display signal cable to the video connector on the back of your computer.
4. Plug the power cord of your computer and your display into a nearby outlet.
5. Turn on your computer and display.
If your monitor displays an image, installation is complete. If it does not display an image, please refer Troubleshooting.
To protect equipment, always turn o the PC and LCD monitor before connecting.
10
Adjusting
Hotkeys
1
2
4 3
5
1 Source/Exit/Up
2 Eco/DCR/Uniformity/Down
3 Clear Vision/Left
4 Volume/Right
5 Power/ Menu/Enter
Power/ Menu/Enter
When the monitor is o, press this key to turn on the monitor.
When the monitor is on, press this button to activate the OSD menu or conrm the function adjustment (press the “down”
button to conrm the selection in the rst-level menu); when the OSD menu is o, press and hold this button for about 2
seconds to shut down.
Volume/increase/right
When the OSD menu is closed, press the “right” key to open the volume adjustment bar, and press the “left” or “right” key
to adjust the output volume of the headset.
Eco/DCR/uniformity/down
When the OSD menu is closed, press the “down” key to enter the brightness prole/dynamic contrast/uniformity
compensation adjustment, press the “left” or “right” key to select dierent brightness proles, turn on the dynamic contrast
and uniformity make up.
Source/exit/up
When the OSD menu is o, press the “up” key to activate the signal source switching function, press the “up” or “down”
key to select the signal source displayed in the information bar, and press the “menu” key to adjust to the selected signal
source .
When the OSD menu is active, press the “up” key as the exit key (to exit the OSD menu).
11
Clear Vision
1. When there is no OSD, Press the “Left” button to activate Clear Vision.
2. Use the “Left” or “Right” buttons to select between weak, medium, strong, or o settings. Default setting is always “o”.
3. Press and hold “Left” button for 5 seconds to activate the Clear Vision Demo, and a message of “Clear Vision Demo:
on” will be display on the screen for a duration of 5 seconds. Press and hold “Left” button for 5 seconds again, Clear
Vision Demo will be o.
Clear Vision function provides the best image viewing experience by converting low resolution and blurry images into
clear and vivid images.
Clear Vision
O
Adjust the Clear Vision
Weak
Medium
Strong
Clear Vision Demo On or O Disable or Enable Demo
12
OSD Setting
Basic and simple instruction on the control keys.
Luminance Color Setup Picture Boost OSD Setup ExitExtra
Contrast 50
Brightness 90
Eco mode Standard
Gamma Gamma 1
DCR Off
Overdrive Off
HDR Off
1). Press the MENU-button to activate the OSD window.
2). Press Left or Right to navigate through the functions. Once the desired function is highlighted, press the MENU-
button to activate it, press Left or Right to navigate through the sub-menu functions. Once the desired function is
highlighted, press MENU-button to activate it.
3). Press Left or Right to change the settings of the selected function. Press Exit–button to exit. If you want to adjust
any other function, repeat steps 2-3.
4). OSD Lock/Unlock Function: To lock or unlock the OSD, press and hold the Down–button for 10s while OSD function
is not active.
Notes:
1). If the product has only one signal input, the item of “Input Select” is disable to adjust.
2). If the product screen size is 4:3 or input signal resolution is native resolution, the item of “Image Ratio” is disabled.
3). One of Clear vision, DCR, DCB Mode, and Picture Boost functions is activated; the other three functions are turned
o accordingly.
13
Luminance
Luminance Color Setup Picture Boost OSD Setup ExitExtra
Contrast 50
Brightness 90
Eco mode Standard
Gamma Gamma 1
DCR Off
Overdrive Off
HDR Off
Contrast 0-100 Contrast from Digital-register.
Brightness 0-100 Backlight Adjustment
Eco mode
Standard Standard Mode
Text Text Mode
Internet Internet Mode
Game Game Mode
Movie Movie Mode
Sports Sports Mode
Reading Reading Mode
Uniformity Uniformity Mode
Gamma
Gamma1 Adjust to Gamma 1
Gamma2 Adjust to Gamma 2
Gamma3 Adjust to Gamma 3
DCR
O Disable dynamic contrast ratio
On Enable dynamic contrast ratio
Overdrive
Weak
Adjust the response time.
Medium
Strong
O
HDR
O / DisplayHDR / HDR
Picture / HDR Movie /
HDR Game
Disable or Enable HDR
HDR Mode O / HDR Picture / HDR
Movie / HDR Game Disable or Enable HDR Mode
Note:
When HDR is detected, the HDR option is displayed for adjustment; when HDR is not detected, the HDR Mode option is
displayed for adjustment.
14
Color Setup
Picture Boost OSD Setup ExitExtra
Luminance
Red 50
Green 50
Blue 50DCB Demo Off
Color Temp. Warm LowBlue Mode Off
DCB Mode Off
Color Setup
Color Temp.
Warm Recall Warm Color Temperature from EEPROM.
Normal Recall Normal Color Temperature from EEPROM.
Cool Recall Cool Color Temperature from EEPROM.
sRGB Recall SRGB Color Temperature from EEPROM.
User Restore User Color Temperature from EEPROM.
DCB Mode
Full Enhance On or O Disable or Enable Full Enhance Mode
Nature Skin On or O Disable or Enable Nature Skin Mode
Green Field On or O Disable or Enable Green Field Mode
Sky-blue On or O Disable or Enable Sky-blue Mode
AutoDetect On or O Disable or Enable AutoDetect Mode
OFF on or o Disable or Enable DCB Mode
DCB Demo On or O Disable or Enable Demo
Red 0-100 Red gain from Digital-register.
Green 0-100 Green gain from Digital-register.
Blue 0-100 Blue gain from Digital-register.
LowBlue
Mode
Multimedia
Decrease blue light wave by controlling color
temperature
Internet
Oce
Reading
O
Note:
When “HDR Mode” under “Luminance” is set to a non-o state, all items under “Color Settings” cannot be adjusted.
15
Picture Boost
OSD Setup ExitExtra
Luminance
Brightness 50
Contrast 50
H. Position 0
V. Position 0
Bright Frame off
Frame Size 14
Picture Boost Color Setup
Bright Frame on or o Disable or Enable Bright Frame
Frame Size 14-100 Adjust Frame Size
Brightness 0-100 Adjust Frame Brightness
Contrast 0-100 Adjust Frame Contrast
H. position 0-100 Adjust Frame horizontal Position
V. position 0-100 Adjust Frame vertical Position
Note:
Adjust the brightness, contrast, and position of the Bright Frame for better viewing experience.
16
OSD Setup
Exit
Color Setup
H. Position 50
0V. Position
Transparence 25
Language English
DP Capability 1.2/1.4 USB 2.0
Timeout 10 Break Reminder Off
USB Selection Auto
OSD Setup Picture Boost
Luminance
Extra
Language Select the OSD language
Timeout 5-120 Adjust the OSD Timeout
DP Capability 1.1/1.2/1.4
If the DP video content supports DP1.2/1.4, please
select DP1.2/1.4 for DP Capability; otherwise, please
select DP1.1
H. Position 0-100 Adjust the horizontal position of OSD
V. Position 0-100 Adjust the vertical position of OSD
USB 3.2Gen1/2.0 or
o
For model need to turn on/o USB power during power
saving
Transparence 0-100 Adjust the transparence of OSD
Break Reminder on or o Break reminder if the user continuously work for more
than 1hrs
USB Selection Auto / USB C /
USB up
*Auto : switch with display input source
*USB C / USB up : x up stream not change with input
source
Note:
When the USB is set to 3.2Gen1, the maximum resolution of the USB C interface is 3840x2160@30Hz; when the USB is
set to 2.0 or o, the maximum resolution of the USB C interface is 3840x2160@60Hz.
17
Extra
Exit
00
Input Select
Off Timer
Auto
Auto Config. No
Reset No
Image Ratio Wide
DDC/CI Yes
Picture Boost OSD Setup
Resolution : 1920(H)X1080(V)
H. Frequency : 67KHz
V. Frequency : 60Hz
Extra Luminance Color Setup
Input Select Select Input Signal Source
O timer 0-24hrs Select DC o time
Image Ratio
Wide
Select image ratio for display
4:3
1:1
Movie1
Movie2
DDC/CI Yes or No Turn ON/OFF DDC/CI Support
Reset
yes or no Reset the menu to default.
(ENERGY STAR® available for selective
models.)
ENERGY STAR® or no
18
Exit
Exit Luminance Color Setup Picture Boost OSD Setup Extra
Exit Exit the main OSD
Table of contents
Other AOC Monitor manuals
