AOK AC202-02 User manual

-40℃～+85℃
AC202-02
38KHZ
2.Parameters
≤500W
230VAC 50Hz
AC202-02Radio Receiver Manual V 1 .0.2
1.Features
!
3.Wiring
AC118-01
IR Remote Control
≤
80M
AC112-04
AC104-02
AC118-01
Infrared control
AC118-01 AC104-02
AC112-04
AC202-02
Receiver
433.92HZ
AC104-02
RF Remote control
IR
RF
≤
8M
AC112-04
Warning
Power off before wiring Avoid static damage Earth wire must be
connected well and correctly
To keep good control
range, avoid connect
metal parts
Manual switch wiring terminal
+5V:IR voltage
IR:IR signal
U:UP/DOWN(brown)
N:Neutral(Blue)
E: Earth (Yellow/Green)
L:Live(Brown)
Power wiring terminal
E:Earth (Green/Yellow)
N:Neutral(Blue)
L:UP /Down(Black)
R:Down/UP (Brown)
Motor wiring terminal
Model No. Voltage Temperature Receive distance Loading Power Operation Mode
Manual pulse Switch
Work with all A-OK tubular motor
SMT machine automatical assembly, dampproof craft
Support of IR,RF,Manualcontrol and DC12V trigger
Work with motorized projection screen, motorized
awning, roller blinds etc
RF Control Manual Switch
Frequency
IR
RF RF, IR and Manual
control, DV12V trigger
signal light
IR receive head
program button
sw1 up
sw2 stop
sw3 down
IR transmitter
projector
IR receive head
Manual switch and IR receive
N:Noutral(Blue) E:Earth(Yellow/Green)
L:Live(brown)
N:Noutral(Blue) E:Earth(Yellow/Green) L:UP/Down(Black) R:Down/UP(Brown)
RF transmitter
Motor
power input
Manual switch operate instruction:
1:press up key less than1's the motor
run up,more than 1's then loose up,
the motor stop
2:press down key less 1's and motor
run down,more than 1's loose and
motor stop
Wiring
NC:empty terminal
GND: earth wire
+12V:DC trigger
out-link projector terminal
S:stop(green)
D:Down/up(black)
G:Neutral(BLUE)
Metal Parts
up
stop
down

Remark:
①IR remote control must make program (same as RF operation), while within effective range.
②Receiver would come back the original state if there are not any operations within 10's.
③Only total 20 IR or RF transmitter can be programmed with 1 receiver
④The longest working time of motor is 5 minutes
Function Adjustment
4.Program setting（select delete channel before operation）
5.Delete all codes on receiver
4's
Power On receiver
Press the transmitter's
UP button
Program finished
Items
When operate,the transmitter's LED1
work well ,and the receiver doesn't action
The transmitter's LED isn't bright or dark bright
The control system work well ,but the motor is out of working
Trouble phenomenon Test/Solution/ probable cause
Have a check with the receiver's wiring
correct or not ,or the program setting is OK
Checking the motor's wiring correct or not ,
and the motor had damage or not
Check the battery power is Ok or not
(The battery install is OK or not )
press program button“sw4” once
signal light flash
operate within 10's
to next step
Power On receiver
Press program button“sw4”
for more than 4's
signal light
flash quickly
and loose up
signal light flash quickly
operate within 6's
to next step
press program button“sw4” once
signal light
flash stop
All code deleted
6.Delete single code on receiver（select delete channel before operation）
Power On receiver
press program button“sw4” once
signal light flash
operate within 10's
to next step
press down button once
signal light
flash stop
signal light
flash stop
Single code deleted
7.Change direction
Power On receiver
press program button“sw4”once
signal light flash
operate within 10's
to next step
press stop button once
signal light
flash stop
Direction changed
8.Troubles handle
Press up key,motor run down, press down key,motor run up set change direction on control or exchange the
up and down wire of motor
4