Aosom A91-169 Installation guide

ASSEMBLY & INSTRUCTION MANUAL
INamc002V01_US_CA
A91-169
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY

Safety
Before you undertake any exercise program, please be sure to consult with your doctor.Fre-
quent strenuous exercise should be approved by your doctor and proper use of your product is
essential. Excessive or incorrect training may result to health injuries. Please read this manual
carefully before commencing the assembly of your product or starting to exercise.
• Please keep all children away from this item when in use. Do not allow children to climb or
play on them when they are not in use.
• Supervise teenagers while they use this unit.
• For your own safety, always ensure that there is at least 3 feet of free space in all directions
around your product while you are exercising.
• Regularly check to see that all nuts, bolts and fittings are securely tightened. Periodically
check all moving parts for obvious signs of wear or damage.
• Any adjustment devices that could interfere with the user's movement on this unit should not
be left projecting.
• Clean only with a damp cloth, do not use solvent cleaners. If you are in any doubt, do not use
your product; contact CUSTOMER SUPPORT.
• Before use, always ensure that your product is positioned on a solid, flat surface. If necessary,
use a rubber mat underneath to reduce the possibility of slipping.
• Always wear appropriate clothing and footwear such as training shoes when exercising. Do not
wear loose clothing that could become caught in moving parts during exercise.
• Do not use this unit if it is not functioning properly or if it is not fully assembled.
• Do not use this unit for commercial purposes. This unit is for home use only.
• Before use, you must read and understand all instructions & warnings stated in this Owner’s
Manual as well as posted on the equipment.
• It is the facility owner’s responsibility to properly instruct users on the proper operation of the
equipment and to warn them of the potential hazards.
• If at any time during exercise you feel faint, dizzy or experience pain, stop and consult your
physician.
Assembling Tools
- Ruler with both metric and English measurements
- 2 x Adjustable Wrenches
- 1 x Philips (”Crosshead”) Screw Driver
Weight Limit
Your product is suitable for users weighing: 150kg or less.
Storage and Use
Your product is intended for use in clean dry conditions. You should avoid storage in excessively
cold or damp places as this may lead to corrosion and other related problems.
General Information
2

Hardware List
The following hardware is used to assemble your unit. Please take a moment to familiarize yourself with these
items. Please note some of this hardware is already pre-assembled on the machine. Do not be alarmed if you
see parts on this page that are not included in your hardware packet.
WASHER
#56. Washer (M8)
[15 Pieces]
Pre-assembled [3 Pieces]
#55. Washer (M10)
[24 Pieces]
#39. Quick Clip
Tool
[2 Pieces]
#45. Hex Bolt (M10x140 mm)
[1 Piece]
#46. Hex Bolt (M10x85 mm)
[4 Pieces]
#47. Hex Bolt (M10x75 mm)
[2 Pieces]
#48. Hex Bolt (M10x70 mm)
[2 Pieces]
#49. Hex Bolt (M10x65 mm)
[1 Piece]
#50. Hex Bolt (M10x25 mm)
[2 Pieces]
#41. Right Safety Hook
#51. Hex Bolt (M8x40 mm)
[8 Pieces]
#42. Left Safety Hook
[1 Piece] [1 Piece] [3 Pieces]
NUT
#54. Nylon Nut (M8)
[2 Pieces]
Pre-assembled
#53. Nylon Nut (M10)
[12 Pieces]
OTHERS
#52. Hex Bolt (M8x20 mm)
[7 Pieces]
Pre-assembled [3 Pieces]
#38. Knob Bolt (M10x60 mm)
#43. Pop-Pin (10x105 mm)
[1 Piece]
#44. Pop-Pin (8x70 mm)
[1 Piece]
[3 Pieces]
BOLT
3

Parts Listing
The following parts list describes all of the parts illustrated on the
exploded diagram on the following page. Please note, most of
these parts are already pre-assembled on your unit.
# Description # Description
01 Right Upright 29 Square End Cap (50 mm)
02 Left Upright 30 Round End Cap
03 Rear Cross Tube 31 Round End Plug (25 mm)
04 Main Frame 32 Bumper
05 Front Upright 33 Adjustable Knob
06 Front Stabilizer 34 Square Spacer (60x50 mm)
07 Adjustable Upright Tube 35 Square Spacer (50x10 mm)
08 Leg Developer 36 AB Strap
09 Backrest Adjustment Tube
10 Backrest Supporting Tube
38 Knob Bolt (M10x60 mm)
11 Supporting Tube
39 Quick Clip
12 Foam Roller Tube
40 Spring Clip
13 Weight Plate Post
41 Right Safety Hook
14 Arm Curl Frame
42 Left Safety Hook
15 Olmypic Adapter
43 Pop-Pin (10x105 mm)
16 Arm Curl Bar
44 Pop-Pin (8x70 mm)
17 Reinforcement Plate
45 Hex Bolt (M10x140 mm)
18 Backrest Cushion Post
46 Hex Bolt (M10x85 mm)
19 Backrest Cushion
47 Hex Bolt (M10x75 mm)
20 Seat Cushion
48 Hex Bolt (M10x70 mm)
21 Arm Curl Cushion
49 Hex Bolt (M10x65 mm)
22 Foam Roller
50 Hex Bolt (M10x25 mm)
23 Foam Grip
51 Hex Bolt (M8x40 mm)
24 Round End Cap (25 mm)
52 Hex Bolt (M8x20 mm)
25 Rectangular End Cap (30x60 mm)
26 Square End Cap (45 mm)
54 Nylon Nut (M8)
27 Square End Cap (25 mm)
55 Washer (M10)
28 Square End Cap (60 mm)
56 Washer (M8)
57 Square Spacer (50x45 mm)
53 Nylon Nut (M10)
4

The following diagram is provided to help you familiarize yourself with the parts and
hardware that will be used during the assembly process. Please note that not all of the
parts and hardware you see here will be used while you are assembling the machine
because some of these items are already pre-installed. Please continue to the next
page to begin the assembly process and use this page only as a reference guide for
parts and hardware.
Exploded Diagram
5

Assembly Instructions
(REAR)
(FRONT)
A
B
AssemblyS tep 1Hardware Required
A). With the help of an assistant, stand both Right
Upright (#01) and Left Upright (#02) on level flooring
as illustrated.
Attach the Rear Cross Tube (#03) to the Right/Left
Uprights (#01/#02) and secure together by inserting
from the rear side as illustrated -- on each side -- two
Hex Bolts (#46) through two Washers (#55) followed
by an additional two Washers (#55) and two Nylon
Nuts (#53).
B. Attach/insert the Backrest Adjustment Tube (#09)
onto the same bracket notch settings*** on both Right
Upright (#01) and Left Upright (#02).
***NOTE:
Please ensure any settings on left/right sides match
and are equal for alignment to avoid serious injury.
WASHER
#55. Washer (M10)
[8 Pieces]
#46. Hex Bolt (M10x85 mm)
[4 Pieces]
NUT
#53. Nylon Nut (M10)
[4 Pieces]
BOLT
55
40
1 2 3 4
55
40
1 2 3 4
STEP3:
6

AssemblyS tep 2
Hardware Required
Assembly Instructions
A). Remove the two Nylon Nuts (#54) pre-assembled on the Left/Right Safety Hooks (#42/#41). Set them aside
nearby for now.
On the left side, insert Left Safety Hook (#42) into the hole on top of left Adjustable Upright Tube (#07) as shown.
Secure using one Nylon Nut (#54) from the inner side.
Select the desired height*** for the Adjustable Upright Tube (#07) on the Left Upright (#02) and secure by screwing
one Knob Bolt (#38) through both the rear of Left Upright (#02) and Adjustable Upright Tube (#07).
Repeat this process on the right side with Right Safety Hook (#41), Right Upright (#01), and the other Adjustable
Upright
Tube (#07).
***NOTE: Please ensure any settings on left/right sides match and are equal for alignment to avoid serious injury.
B). On the left side, insert the Weight Plate Post (#13) in through the side hole of Left Upright (#02). Secure from
the inner side using one Hex Bolt (#52) through one Washer (#56). Attach the Quick Clip (#39) to the outer side of
Weight Plate Post (#13).
Repeat this process on the right side with the other Weight Plate Post (#13) and Right Upright (#01).
WASHER
#56. Washer (M8)
[2 Pieces]
#41. Right Safety Hook
#42. Left Safety Hook
[1 Piece] [1 Piece]
NUT
#54. Nylon Nut (M8)
[2 Pieces]
OTHERS
BOLT
#52. Hex Bolt (M8x20 mm)
[2 Pieces]
#38. Knob Bolt (M10x60 mm)
[2 Pieces]
#39. Quick Clip
[2 Pieces]
(RIGHT)
(LEFT)
A
B
7

AssemblyS tep 3
A). Remove the three Hex Bolts(#52) and three Washers (#56) pre-assembled on the Front Stabilizer (#06). Set
them aside nearby for now.
Attach the Front Upright (#05) to the Front Stabilizer (#06) and secure by using two Hex Bolts (#52) through two
Washers (#56) from each side as illustrated.
B). Attach the Front Upright (#05) to the Main Frame (#04) and secure by using two Hex Bolts (#50) through two
Washers (#55) and then two additional Washers (#55) and two Nylon Nuts (#53).
C). Attach the Main Frame (#04) over and onto the Rear Cross Tube (#03) by inserting two Hex Bolts (#48) through
two Washers (#55) and from the bottom one Reinforcement Plate (#17), an additional two Washers (#55), and two
Nylon Nuts (#53).
D). Attach the Supporting Tube (#11) to the bottom of Main Frame (#04) inserting downward one Hex Bolt (#49)
through one Washer (#55) followed by an additional Washer (#55) and one Nylon Nut (#53), and, to the back of
Front Stabilizer (#06) using one Hex Bolt (#52) through one Washer (#56) as shown in the diagram below.
Assembly Instructions
Hardware Required
WASHER
#56. Washer (M8)
[3 Pieces]
#55. Washer (M10)
[10 Pieces]
#48. Hex Bolt (M10x70 mm)
[2 Pieces]
#49. Hex Bolt (M10x65 mm)
[1 Piece]
#50. Hex Bolt (M10x25 mm)
[2 Pieces]
NUT
#53. Nylon Nut (M10)
[5 Pieces]
BOLT
#52. Hex Bolt (M8x20 mm)
[3 Pieces]
C
D
B
A
8

AssemblyS tep 4
A). Attach the Leg Developer (#08) by aligning the holes to bracket of Front Upright (#05). Secure together using
one Hex Bolt (#47) through one Washer (#55) and an additional Washer (#55) followed by one Nylon Nut (#53) as
illustrated.
B). Slide one Foam Roller (#22) onto one end of a Foam Roller Tube (#12). Next, slide the same Foam Roller Tube
(#12) through the lower hole of the Leg Developer (#08) as illustrated. Next, slide one more Foam Roller (#22) onto
the other end of the Foam Roller Tube (#12) (after it has been inserted through the lower hole).
Repeat this process with the other Foam Roller Tube (#12) and the two other Foam Rollers (#22) through the
upper hole on the Leg Developer (#08).
C). Attach the four Round End Caps (#30) on the outside of the four Foam Rollers (#22).
D). Attach the Olympic Adapter (#15) over the protruding tube of Leg Developer (#08) and secure using Quick Clip
(#39) as illustrated below.
Assembly Instructions
Hardware Required
WASHER
#55. Washer (M10)
[2 Pieces] #39. Quick Clip
#47. Hex Bolt (M10x75 mm)
[1 Piece]
[1 Piece]
NUT
#53. Nylon Nut (M10)
[1 Piece]
OTHERS
BOLT
55
40
OLYMPIC ADAPTER
If you intend to use Olympic plates,
slide the Olympic Adapter (#15)
over the standard plate post and
secure it with one
(#39).
Quick Clip
*FOAM R O LLE R S
The Foam Roller Tube (#12)
can be placed through either
of these two holes depending
on your height. Simply
remove the Round End Cap
(#30) and one Foam Roller
(#22) from one end to reposition
the location of the Foam Roller
Tube (#12).
A
B
C
D
9

Assembly Instructions
AssemblyS tep 5
A). Attach the Arm Curl Bar (#16) to the Leg Developer
(#08) by aligning the holes on bracket of Leg Developer
(#08) and securing them with one Hex Bolt (#47) through
one Washer (#55) followed by an additional Washer
(#55) and one Nylon Nut (#53) as illustrated.
B). For added versatility to your workouts, you may attach
the AB Strap (#36) to the bracket of Arm Curl Bar (#16)
using the Spring Clip (#40).
Hardware Required
WASHER
#55. Washer (M10)
[2 Pieces]
#47. Hex Bolt (M10x75 mm)
[1 Piece]
NUT
#53. Nylon Nut (M10)
[1 Pieces]
BOLT
#44. Pop-Pin (8x70 mm)
[1 Piece]
OTHERS
A
B
10

AssemblyS tep 6
A). With the help of an assistant, insert the two pegs on the sides of the Backrest Cushion Post (#18) into the two
side holes located on the inside of both Backrest Supporting Tubes (#10). While simultaneously holding these three
pieces together, align and slide the two holes on the bottom of the Backrest Supporting Tubes (#10) onto each side
of the “welded rod” on Main Frame (#04). Secure by inserting one Hex Bolt (#45) through one Washer (#55)
followed by one additional Washer (#55) and one Nylon Nut (#53). Please DO NOT OVER-TIGHTEN.
B). Insert the Arm Curl Frame (#14) into the Front Upright (#05) and secure it in place with one Knob Bolt (#38) as
illustrated below.
C). Insert the Pop-Pin (#43) into the hole on back of Main Frame (#04) for now. This Pop-Pin (#43) will allow you to
adjust seating positions for versatile workouts.
Assembly Instructions
Hardware Required
WASHER
#55. Washer (M10)
[2 Pieces]
#45. Hex Bolt (M10x140 mm)
[1 Piece]
NUT
#53. Nylon Nut (M10)
[1 Pieces]
OTHERS
#38. Knob Bolt
(M10x60 mm) [1 Piece]
#43. Pop-Pin (10x105 mm)
[1 Piece]
BOLT
LOCK PIN
The
is used to place the
backrest into the
position quickly.
Pop-pin (#43)
Remove the Pop-pin
(#43) for all other
positions and insert it
into the hole on the
Main Frame (#04)
when it is not in use.
C
KNOB BOLT
The Knob Bolt (#38) is used to adjust the height
of the Arm curl pad post. Simply unscrew the
Knob bolt (#38), reposition the height of the
Arm Curl Frame (#14) and then tighten the Knob
Bolt (#38).
A
B
“Welded Rod”
11

AssemblyS tep 7
A). Attach the Backrest Cushion (#19) gently onto the Backrest Supporting Tubes (#10) by inserting and securing
four Hex Bolts (#51) through four Washers (#56) from underneath the Backrest Cushion (#19).
B). Attach the Seat Cushion (#20) to the two tubes on the Main Frame (#04) as shown in diagram. Secure them
together by inserting upward four Hex Bolts (#51) through four Washers (#56).
C). Attach the Arm Curl Cushion (#21) to the Arm Curl Frame (#14) using two Hex Bolts (#52) through two Wash-
ers (#56).
The assembly process is now complete. However, for your own safety, please make sure to read this entire Own-
er's Manual which includes safety instructions and warnings, as well as any safety/warning labels affixed to the
product before use.
Assembly Instructions
Hardware Required
WASHER
#56. Washer (M8)
[10 Pieces]
#51. Hex Bolt (M8x40 mm)
[8 Pieces]
BOLT
#52. Hex Bolt (M8x20 mm)
[2 Pieces]
A
B
C
12

• Make sure all nuts and bolts are tightened (but do not over-tighten).
• Check for any loose parts and components and tighten prior to each use.
• Check to see if there are any tears or bends in the welding or metal prior to each use.
Do NOT use the product if you find any such tears or bends. Please contact our Customer
Service.
• Be sure that all adjustment locking devices and safety devices are properly located and fully
engaged prior to use!
FINAL CHECK (Before EACH use)
13

Before use, you must read and understand all instructions & warning stated in this Owner's
Manual as well as posted on the equipment.
The following flexibility exercises are provided to you as a means to prevent injury while you are
exercising. A proper warm-up routine decreases the chance of injuring your muscles while you
are exercising. Please take the time to do these flexibility exercises before and after each time
you exercise.
Groin Stretch
1. Sit with your knees flexed
and soles of feet together.
2. Hold your ankles and bend
at your hips (keep your back
straight) as you press your
knees toward the floor with
your elbows.
Hip Stretch
1. Lie on your back and raise your right leg as you clasp both
hands under the back of the knee. Keep your left leg straight.
2. Gently pull your right leg toward your trunk without raising
your upper body. Switch leg positions and repeat.
Quadriceps Stretch
1. Stand on your left leg and
hold onto a support with your
left hand.
2. Flex your right leg behind
you, grasp your ankle or foot
with your right hand and pull
your foot toward your buttocks.
Keep your back straight and
right knee pointed down.
Repeat on the other leg.
Hamstring Stretch
1. Sit with your left leg extended and
bend your right leg at the knee as
you place the sole of your right foot
against the inner thigh of your
extended leg.
2. Flex the foot of your extended leg
(toes pointed toward ceiling) and
gently bend forward from your hips;
keep your back straight.
3. Reach your hands on your
extended leg as far as possible and
then switch legs and repeat.
Trunk Twister
1. Sit with your leg extended and bend
your right knee as you cross your right
leg over your left leg. Your right foot
should be flat on the floor alongside
your left knee.
2. Place your left arm on the outside
of your right leg and pull against that
leg while twisting your trunk as far as
possible to the right. Place your right
hand on the floor behind your
buttocks. Reverse leg positions and
repeat.
Warm-Up Instructions
14

Shoulder Stretch
1. Bring your right hand over your
right shoulder to the upper back
and bring your left hand under your
left shoulder to the upper back.
2. Try to reach your fingertips. If
you are not able to reach your
fingertips, use a towel as an
extension of your hands and gently
pull one hand toward the other.
Reverse arm positions and repeat.
Calf Stretch
1. Place both hands against a wall
to aid your balance. Press the ball
of your left foot against the wall
and keep the heel of the same
foot rested on the floor (make sure
your left knee is bent).
2. Slowly start to straighten your
left knee and you will feel the
muscles in your left calf stretch.
Switch leg positions and repeat.
Trunk Flexion, Prone
1. Assume the depicted position on your hands and knees. Stretch your hands out in front of you and then
slowly start to pull them back in toward your body as you tuck your chin and arch your back upward.
2. Return to the starting position slowly
Warm-Up Instructions
15

MANUEL D’INSTRUCTIONS
16

Sécurité
Avant d’entreprendre tout programme d’exercice, veillez à consulter votre médecin.
Les exercices intenses et fréquents doivent être approuvés par votre médecin et l'utilisation
correcte de votre produit est essentielle. Un entraînement excessif ou incorrect peut entraîner
des blessures. Veuillez lire attentivement ce manuel avant de commencer l'assemblage de
votre produit ou l'exercice.
• Veuillez tenir tous les enfants à l’écart de ce produit lorsqu’il est utilisé. Ne laissez pas les
enfants grimper ou jouer dessus lorsqu'il n'est pas utilisé
• Supervisez les adolescents pendant qu’ils utilisent cet appareil.
• Pour votre propre sécurité, veillez toujours à ce qu'il y a au moins 1 mètre d'espace libre dans
toutes les directions autour de votre produit pendant que vous vous exercez.
• Vérifiez régulièrement que tous les écrous, boulons et raccords sont bien serrés. Vérifiez
périodiquement que toutes les pièces mobiles ne présentent pas de signes évidents d'usure ou
de dommages.
• Tout dispositif de réglage qui pourrait interférer avec le mouvement de l’utilisateur sur cet
appareil ne doit pas être laissé en saille.
• Nettoyez uniquement avec un chiffon humide, n’utilisez pas de nettoyants solvants. Si vous
avez des doutes, n’utilisez pas votre produit ; contactez LE SOUTIEN A LA CLIENTELE.
• Avant utilisation, assurez-vous toujours que votre produit est positionné sur une surface solide
et plane. Si nécessaire, utilisez un tapis en caoutchouc en dessous pour réduire le risque de
glissade.
• Portez toujours des vêtements et des chaussures appropriés, comme des chaussures d'en-
traînement, lorsque vous vous entraînez. Ne portez pas de vêtements amples qui pourraient se
prendre dans les pièces mobiles pendant l'exercice.
• N’utilisez pas cet appareil s’il ne fonctionne pas correctement ou s’il n’est pas entièrement
assemblé.
• N’utilisez pas cet appareil à des fins commerciales.
Cet appareil est destiné à un usage domestique uniquement.
• Avant toute utilisation, vous devez lire et comprendre toutes les instructions et tous les aver-
tissements figurant dans ce manuel d’instructions ainsi que sur l’équipement.
• Il incombe au propriétaire de l’installation d’enseigner correctement aux utilisateurs le bon
fonctionnement de l’équipement et de les avertir des risques potentiels.
• Si, à tout moment pendant l’exercice, vous vous sentez faible, étourdi ou éprouvez de la
douleur, arrêtez-vous et consultez votre médecin.
Outils d’assemblage
- Règle avec des mesures métriques et anglaises
- 2 x Clés réglables
- 1 x tournevis Philips (« cruciforme »)
Limite de poids
Votre produit convient aux utilisateurs pesants: 150kg ou moins.
Stockage et utilisation
Votre produit est destiné à être utilisé dans des conditions propres et sèches. Vous devez éviter
de le stocker dans des endroits excessivement froids ou humides, car cela peut entraîner de la
corrosion et d'autres problèmes connexes.
General Information
17

Liste du matériel
Le matériel suivant est utilisé pour assembler votre appareil. Veuillez prendre un moment pour vous familiariser
avec ces éléments. Veuillez noter qu’une partie de ce matériel est déjà préassemblé sur la machine. Ne vous
inquiétez pas si vous voyez des pièces sur cette page qui ne sont pas incluses dans votre paquet du matériel.
Rondelle
#56. Rondelle (M8)
[15 Pièces]
Préassemblé [3 Pièces]
#55. Rondelle (M10)
[24 Pièces]
#39. Clip rapide [3 Pièces]
Outil [2 Pièces]
#45. Boulon hexagonal (M10x140 mm) [1 Pièce] #46. Boulon hexagonal
(M10x85 mm) [4 Pièces]
#47. Boulon hexagonal
(M10x75 mm) [2 Pièces]
#48. Boulon hexagonal
(M10x70 mm) [2 Pièces]
#49. Boulon hexagonal
(M10x65 mm) [1 Pièce]
#50. Boulon hexagonal
(M10x25 mm) [2 Pièces]
#41. Crochet de sécurité droit
[1 pièce]
#51. Boulon hexagonal
(M8x40 mm) [8 Pièces]
#42. Crochet de sécurité
gauche [1 pièce]
Ecrou
#54. Ecrou en nylon
(M8) [2 pièces]
Préassemblé
#53. Ecrou en
nylon (M10)
[12 pièces]
Autre
#52. Boulon hexagonal
(M8x20 mm) [7 Pièces]
Préassemblé [3 Pièces]
#38. Boulon à bouton
(M10x60 mm) [3 Pièces]
#43. Goupille (10x105 mm)
[1 Pièce]
#44. Goupille (8x70 mm) [1 Pièce]
Boulon
18

Liste des pièces
La liste des pièces suivantes décrit toutes les parties illustrées sur le diagramme explosé sur la page suivante.
Veuillez noter que la plupart de ces pièces sont déjà préassemblées sur votre appareil.
#
Description
#
Description
01
Montant droit
29
Embout carré (50 mm)
02
Montant gauche
30
Embout rond
03
Tube transversal arrière
31
Bouchon rond (25 mm)
04
Cadre principal
32
Pare-chocs
05
Montant avant
33
Bouton réglable
06
Stabilisateur avant
34
Entretoise carrée (60x50 mm)
07
Tube du montant réglable
35
Entretoise carrée (50x10 mm)
08
Exerciseur de jambe
36
Sangle AB
09
Tube de réglage du dossier
38
Boulon à bouton (M10x60 mm)
10
Tube de soutien du dossier
39
Clip rapide
11
Tube de soutien
40
Clip à ressort
12
Tube à rouleaux en mousse
41
Crochet de sécurité droit
13
Montant de la plaque de poids
42
Crochet de sécurité gauche
14
Cadre de flexion de bras
43
Goupille (10x105 mm)
15
Adaptateur olympique
44
Goupille (8x70 mm)
16 Barre de flexion de bras 45 Boulon hexagonal (M10x140
mm)
17
Plaque de renfort
46
Boulon hexagonal (M10x85 mm)
18
Poteau de coussin du dossier
47
Boulon hexagonal (M10x75 mm)
19
Coussin du dossier
48
Boulon hexagonal (M10x70 mm)
20
Coussin
49
Boulon hexagonal (M10x65 mm)
21
Coussin de flexion de bras
50
Boulon hexagonal (M10x25 mm)
22
Rouleau de mousse
51
Boulon hexagonal (M8x40 mm)
23
Poignée en mousse
52
Boulon hexagonal (M8x20 mm)
24
Embout rond (25 mm)
53
Écrou en nylon (M10)
25
Embout rectangulaire (30x60 mm)
54
Écrou en nylon (M8)
26
Embout carré (45 mm)
55
Rondelle (M10)
27
Embout carré (25 mm)
56
Rondelle (M8)
28 Embout carré (60 mm) 57 Entretoise carrée (50x45 mm)
19

Le schéma suivant est fourni pour vous aider à vous familiariser avec les pièces et le
matériel qui seront utilisés pendant le processus d'assemblage. Veuillez noter que toutes
les pièces et le matériel que vous voyez ici ne seront pas utilisés lors de l'assemblage de
la machine, car certains de ces éléments sont déjà préinstallés. Passez à la page
suivante pour commencer le processus d'assemblage et utilisez cette page uniquement
comme guide de référence pour les pièces et le matériel.
Vue Eclatée
20