SB SB-LPLRC200S User manual
Owners Manual
and Assembly Guide
SB Fitness Equipment
LAT PULLDOWN / LOW ROW COMBO MACHINE
SB-LPLRC200S
1
#",%", !"$,%", #!",!"$,,
, #!,, ",", $ ,
, #!,, %!!", $,!!,##),
, #!,, $ , ,#%!! "$,!!#,
, #!,, %"", $ ,
, , ,#%!! "$,##),
, , !, $ ,
, , ,, ',$# ,%," ,
, , , $ ,
, ', %," ,(,!$,
, , #$,##),!"$#,
, #, $,#$,
, #, $,#$,
, #, #!",'#",
, #, %$",( ,#"',
, #, %$",( ,#"',
, #, %$,
, #, ( ,# $,,#"',
, #, ( ,# $,,#"',
, #, ( ,# $, %$"#%,
,#"',
, #, ( ,# $,,#"',
, ', %#,
, #, %$",( ,#"',
, #, %$,
, ', $$ , $,!,
, , ,, ',$# ,",
%",
, , ,, ',$# , %$",
%",!$,
, ', $ !,#$,%", %, ,
%$"'$,#$,
, , %#$,#$, ,
%$"'$,!$,
, $ !,#$, , %$"'$
', #$,
, ', %#$, $, ,
%$"'$,!$,
, ', %$"'$,#$,
, ', %$"'$,#%!! "$,!!,
, ,,, ',!%,
,%# ,
#$",#*#,
,
$,
$,
$,
,
,,
,
,
,
,
,
,
,
##),!"$#,, #,
$, ,#!,,
,
,
$,
%$,
,!,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
,
2
PARTS LIST AND PART NUMBERS
3
INSTALL THE WEIGHT STACK FRAME ASSEMBLY(1) TO THE UNDER
FRAME ASSEMBLY(4). INSTALL RUBBER FOOT PADS(24) NOW (OPTIONAL).
4
1.) INSTALL GUIDERODS(7) INTO HOLES LOCATED INSIDE BOTTOM OF WEIGHT
STACK FRAME.
2.) SLIDE #32 SPACERS ON FROM TOP OF GUIDE RODS TO HAVE 2 ON EACH
GUIDE ROD AT THE BOTTOM.
3.) INSTALL WEIGHT PLATES(29). SMALLEST WEIGHT PLATE IS LAST AS THIS IS
THE TOP PLATE.
4.) INSTALL #27 ON TO GUIDE ROD AND INTO TOP PLATE.
5.) INSTALL SELECTOR ROD(28) INTO WEIGHT STACK CENTER HOLE.
6.) SECURE TOP OF GUIDE RODS TO WEIGHT STACK FRAME USING #9 PLATE
AND #17 BOLTS.
7.) PLACE SELECTOR PIN(30) INTO WEIGHT
STACK.
** REFER TO PAGE 10 FOR FURTHER ASSISTANCE**
5
INSTALL THE SUPPORT UPRIGHT ASSEMBLY TO THE UNDER
FRAME ASSEMBLY(4).
6
INSTALL THE UPPER CONNECTING CROSS BEAM TO THE WEIGHT
STACK FRAME AND THE SUPPORT UPRIGHT ASSEMBLY.
7
1.) INSERT THE CABLE END OF THE LONG CABLE FROM THE BOTTOM SIDE OF
THE UPPER CONNECTING CROSS BEAM AND FOLLOW DIAGRAM TO THE TOP
PLATE SELECTOR ROD, THEN INSERT AND TIGHTEN SET SCREWS AFTER
STEP 2.
2.) INSTALL SHORT CABLE AS SHOWN IN DIAGRAM BY GOING UNDER LARGER
LOW-ROW PULLEY AND OVER SMALLER PULLEY. ATTACH PULLEYS AS YOU
INSTALL THE CABLE.
8
INSTALL THE ADJUSTABLE LEG PAD SUPPORT(5) TO THE SUPPORT
UPRIGHT ASSEMBLY. INSERT DROP PIN INTO SELECTOR HOLES FIRST TO HELP
LINE UP #5, #10, #19, AND #21 (PIVOT POINT). THEN ATTACH THE LOW ROW
PLATFORM FOOT SUPPORT(6) TO THE BASE OF THE SUPPORT UPRIGHT
ASSEMBLY, THEN INSERT #11 BOLT THROUGH ALL HOLES TO SECURE PLATFORM
TO THE BASE SUPPORT.
9
INSTALL THE SEAT PAD(33), LAT PULLDOWN BAR, AND FRONT AND
REAR WEIGHT PLATE GUARDS(25 & 26).
!%"%% !"! %$!% %%$!%% %%
%#!$!%%% %%% %%
+++"+*"+!"!+!+"+ !+!+"+!"+
+#+!"+"+++&"++#+!#+*+"+
+!"+(+"+!#+*+"+#+"+!#+!)++"+'++"+##+"+)"+!)!+
$+ $+$+)+!$$+ !!++'%)$++
10
11
INSTALL WEIGHT STACK CABLE
WARNING: THE SCREWS AT EACH JOINT OF THE
WEIGHT STACK CABLE MUST BE FULLY TIGHTENED
"#
#
##
##
##
### !!#!###
!###
# ## !##!#!#
##
##
8
#
#!#
8
#
##
7
+
1212
SB FITNESS EQUIPMENT / SB-LPLRC200S
PRODUCT DESCRIPTION, SPECS, & FEATURES
$$#$#$$$$
$$$#$$$
"$$
$$#$ $$#$#$$$
$$$$$$$
#$$$$$#$$#$
#$$$$$ $$
$!$#$"$$
$#$$$$$$
$$#$$#$$
$$#$$$$$
#$$$$$#$
$$
1213
" """"""""
"""""" """
""""""
"""
""""" """
""""""
""""""
" """""" """
""""" """
"""""""
"
" """""""
"""""""
"""""""
"""
""""&"""
"""""""
""
1214
1215
1216
1217
Other SB Fitness Equipment manuals
Popular Fitness Equipment manuals by other brands
G-FITNESS
G-FITNESS AIR ROWER user manual
CAPITAL SPORTS
CAPITAL SPORTS Dominate Edition 10028796 manual
Martin System
Martin System TT4FK user guide
CIRCLE FITNESS
CIRCLE FITNESS E7 owner's manual
G-FITNESS
G-FITNESS TZ-6017 user manual
Accelerated Care Plus
Accelerated Care Plus OMNISTIM FX2 CYCLE/WALK user manual
