AP&T AP-AB1215 User manual
AP&T
R
High Efficient Electroshock-proof
Intelligent Ion Bar
AP-AB1215
正高压幅值
Vp
Vp Vp
Vp
Vn
Vn Vn
Vn
.
.
，
The effect of static eliminating is better
compare to power frequency AC ion bar
30mm
150mm
0s
0s
0.1s
1.0s
1.7s
3.2s
3.1s
5.1s
2.8s
3.1s
2.3s
6.0s
150mm
50mm
70mm
100mm
：
：4：
Efficiently static removal
No.1
No.2
No.4
No.3
unit：mm
25
3
25
3
16
Φ5
34
25
34
DC
Negative high voltage (orange light on when working)
Positive high voltage (green light on when working)
RJ45 port on the front and back panel of ion bar:
The orange light on the front port and the green light on the back port blink alternately with the working frequency;
The green light works at positive high pressure;
The orange light works at negative high pressure.
..6；
：
（ ）
G，，，
＜
：；：
12
34
+-
OK
CTTH
PWM FREQ CFM
IBV
IBN
123
6
5
4
IBP
CAL ALTH
AP&T
R
1
2
3
4
5
6
7
8
9
55 100
30 100
10 150
5 200
1 250
≥ 100mm
≥ 100mm
60-200mm
Safety warning
+OK -
CTTH
PWM FREQ CFM
IBV
IBN
123
6
5
4
IBP
CAL ALTH
AP&T
R
15
After-sales service
MaintenanceNO. Faults Reasons Solutions
1
The RJ45 power port indicator
on the front panel is off
Poor contact of the power cable
Power supply mismatch
Check whether the power cable is in good condition and securely
connected
Wrong working mode -- Only green light on at the right port (positive
high voltage only) Unplug the power cord and restart the ion bar. Or reset the working
frequency (this lamp is not used to judge the failure of the high
voltage module)
Wrong working mode -- Only orange light on at the right port (negative
high voltage only)
The duty ratio is too small and the green light is dark Adjust duty ratio until ion balance becomes good. Return to factory
for repair if adjustment is not effective.
The duty ratio is too high and the orange light is dark
2
The electrostatic removal
performance decreased
obviously
Discharge needle is polluted and damaged Clean or replace the discharge needle
Whether the discharge seat is tightened Confirm the discharge seat is tightened
Ion bar positioning is incorrect Confirm the best installation location
3There are conductors or other ion bar around
4
High voltage alarm
（Panel indicator red light
on ）
Electromagnetic interference
Remove (moving) conductors or other ion bar
Abnormal discharge
No power supply for high voltage module
High voltage module is damaged Return to factory for maintenance
5Unable to discharge
High voltage module is damaged
Main-board chip is damaged
Return to factory for maintenance
Return to factory for maintenance
Main-board chip is damaged caused by poor grounding or no grounding
6High voltage module is damaged or insulation of the discharge seat is
damaged
The product is smoky or burnt
The electrostatic removal
performance decreased
Check the grounding of the ion bar and plant equipment, and return to
factory for maintenance
Return to factory for maintenance
Confirm the power supply specification（INPUT：100—240VAC
50/60Hz；OUTPUT：24VDC 2000mA）
Turn off the power switch / unplug the power cable, restart the ion bar
Confirm the installation location and stay away from surrounding
conductors
Return to factory for maintenance
Trouble shooting
专业创造价值
AP&T
Professional electrostatic intelligent monitoring/analysis
and elimination solution provider
Speciality Creates Value
AP&T
Shanghai Anping Static Technology Co.,Ltd
Tel : +86-21-64517676
Fax : +86-21-64517673
Postcode : 200233
Website : www.ap-static.com
Address : 3/F,Building 27,No.69,Guiqing Road,Shanghai,China
Table of contents
Popular Control Unit manuals by other brands
GEA
GEA VARIVENT 24/7 PMO Original operating instructions
Elkron
Elkron MR16 Installation and user manual
DeDietrich
DeDietrich JA7 Assembly instructions
Phoenix Mecano
Phoenix Mecano Dewert Okin ACCUCONTROL 4.5 installation instructions
Chicco
Chicco Clip-On Electronic Module owner's manual
GE
GE B90 instruction manual
Festo
Festo MS6N-SV Assembly Installation Safety Instructions
Honeywell
Honeywell Esser IQ8TAL Installation instruction
Pentair
Pentair Aurora CBV-S Installation and operation manual
Toro
Toro 112-4881 installation instructions
ICP DAS USA
ICP DAS USA MDC-700 Series user manual
Sun Oracle
Sun Oracle Sun Blade 6000 Product notes