Apantac OG-US-5000 User manual

APANTAC LLC www.apantac.com i
OG-US-5000 User Manual
OG-US-5000
APANTAC openGear
UHD (HDMI 2.0 and 12G SDI) Bi-directional
Universal Scaler with Genlock
User Manual
Updated: May 2022

APANTAC LLC www.apantac.com i
OG-US-5000 User Manual
Features .................................................................................................1
Contents .................................................................................................2
Installation ..............................................................................................3
Indicators ...............................................................................................4
Control and Configuration ........................................................................5
Software ............................................................................................5
Product Tab ..............................................................................................6
Signal Tab ..........................................................................................7
Configuration Tab (output settings) .....................................................8
Genlock Tab .......................................................................................9
Display Tab (EDID) ..........................................................................10
Network Tab .......................................................................................... 11
Trouble-Shooting ...................................................................................12
Specifications ........................................................................................13
Copyright and Warranty Statements .......................................................14
Table of Contents

APANTAC LLC www.apantac.com 1
OG-US-5000 User Manual
Features:
• OGX/OG3 card-based form factor
• Dashboard control enabled
• Supports HDMI 2.0 and 12G SDI inputs
• Supports HDMI 2.0 and 12G SDI outputs
• Supports 8 channels of HDMI audio to SDI and vise versa
• Supports Genlock via openGear frame
• Scales any SDI input resolution to HDMI and SDI
• Scales any HDMI input resolutions to HDMI and SDI
• SDI output supports 1080P, UHD (2160P), and 4K-DCI in 50 and 59.94Hz
• HDMI output support 1080P in 50, 59.94Hz, UHD (2160P) in 30, 50, 59.94Hz, and 4K-DCI
in 50 and 59.94Hz.
• Low power consumption - < 25W
• 5 year limited warranty

APANTAC LLC www.apantac.com 2
OG-US-5000 User Manual
1 x OG-US-5000-MB, main board
1 x OG-US-5000-RM, rear module
1 x 75 ohm Terminator
1 x Screw and washer
Contents:

APANTAC LLC www.apantac.com 3
OG-US-5000 User Manual
Card Installation
Install the Apantac OG-US-5000 rear module (RM). Secure
with the included screw and washer.
Insert main board in the appropriate slot to match the RM
card edge connector. Insure the main board is firmly
seated into the RM connector.
Note: Apantac rear modules typically occupy two
openGear card slots. The slot the main board will utilize
depends on the position of the card edge connector on the
rear module, which varies by model.
Output Video - SDI
Connect the SDI output to the receiving/down-stream equipment.
If only one output is to be used, terminate the unused SDI output with the included 75-ohm BNC terminator.
Output Video - HDMI
Connect the HDMI output to the receiving/down-stream equipment using a UHD/4K HDMI cable.
HDMI extenders which draw power from the HDMI port must comply with HDMI power specifications.
Input Video - SDI
Connect an SDI video source to the SDI video input BNC connector using 12G capable 75ohm SDI cable.
Input Video - HDMI
Connect an HDMI video source to the HDMI video input connector with any UHD/4K HDMI cable.
Notes:
• The OG-US-5000 video input is not auto-detecting. The unit must be configured to
identify which video input source is to be processed (HDMI or SDI).
• For HDMI sources containing content protection (HDCP) content Apantac technical
support.
Installation:

APANTAC LLC www.apantac.com 4
OG-US-5000 User Manual
Indicators:
SDI Input Status Indicator:
• Blinking-green* when the OG-US-5000 has recognized and locked on to the SDI video input signal.
• Solid green, no signal recognition.
HDMI Input Status Indicator:
• Blinking-green* when the OG-US-5000 has recognized and locked on to the HDMI video input signal.
• Solid green, no signal recognition.
* Indicators may function differently depending on firmware revisions.

APANTAC LLC www.apantac.com 5
OG-US-5000 User Manual
Control and Configuration:
Software:
The Apantac OG-US-5000 model is controlled and configured through the openGear frame’s
control software ‘Dashboard’ by Ross Video inc. Dashboard can be acquired through the Ross
Video website; https://www.rossvideo.com
Dashboard software runs on PC’s and connects to the openGear frame’s control card via Ether-
net. The IP address of the openGear frame is displayed on the LCD panel on the front of the
frame. The openGear frame may have a fixed IP address or use DHCP.
The openGear frame’s control card communicates to the individual openGear cards via the
frame’s internal CANBUS (Controlled Area Network). CANBUS communicates to the frame’s
slots and all control and configuration of the OG-US-5000 cards is through the Dashboard-
CANBUS channels.
The Apantac OG-US-5000 Dashboard interface is shown above. Each Apantac OG-US-5000 card
should be recognized by Dashboard and displayed by the installed slot number.

APANTAC LLC www.apantac.com 6
OG-US-5000 User Manual
Product Tab
The Product tab is informational only. There are no settings or options.
Firmware:
‘Software Rev’, ‘FPGA Version’, and ‘Firmware Rev’ items indicate the currently installed firmware of the
OG-US-5000. These values should appear as dates similar to shown above. If they show as ‘0’ or not at
all, this may indicate a hardware failure, power cycle the card and check whether firmware numbers are
restored.
Software Rev: This is the firmware of the OG-US-5000’s Dashboard User Interface.
FPGA Version and Firmware Rev: This is the firmware of the OG-US-5000’s video processor.

APANTAC LLC www.apantac.com 7
OG-US-5000 User Manual
Signal Tab:
Unit Status Indicators:
Card State: Indicates whether Dashboard software detects an error state from the card. If ANY of the Signal
tab indicators are red, then the card state will show red. NOTE: this includes lack of gen-lock even when the
genl-lock feature is disabled.
Connection: Indicates whether Dashboard software is communicating via CANBUS with the card.
Signal Status Indicators:
Input Signal: Indicates whether the OG-US-5000 has detected and locked-on to the incoming video signal
(either SDI input or HDMI input, as configured).
SDI Output: Indicates whether the OG-US-5000 is generating an SDI video signal on the outputs. Requires a
successful Input Video Signal lock.
Reference: Indicates the OG-US-5000 is receiving a valid genlock reference signal.
Lock Status: Indicates whether the SDI output video signal is locked to the genlock reference signal.

APANTAC LLC www.apantac.com 8
OG-US-5000 User Manual
Mode:
The OG-US-5000’s video input is not auto-detecting. The card must be configured for which input to pro-
cess.
The mode choices are:
• SDI to SDI conversion; chooses the SDI video input signal for conversion to both HDMI and
SDI outputs.
• HDMI to SDI conversion; chooses the HDMI video input signal for conversion to both HDMI
and SDI outputs. (For HDMI sources requiring HDCP, contact Apantac Technical Support.)
• Test Signals; generates a color-bar test pattern on the SDI outputs.
SDI Output Format:
This option configures the resolutions and refresh rate of the SDI output video signal.
Options are:
• 4K-UHD @ 59.94 Hz
• 4K-UHD @ 50 Hz
• 4K-DCI @ 59.94 Hz
• 4K-DCI @ 50 Hz
• 1080p @ 59.94 Hz
• 1080p @ 50 Hz
HDMI Output Format:
This option configures the resolutions and refresh rate
of the HDMI output video signal.
Options are:
• 4K-UHD @ 59.94 Hz
• 4K-UHD @ 50 Hz
• 4K-DCI @ 59.94 Hz
• 4K-DCI @ 50 Hz
• 2160p @ 30 Hz
• 1080p @ 59.94 Hz
• 1080p @ 50 Hz
Embedded Audio:
This option configures the SDI video output signal. Options are:
• Enabled
• Disabled (outputs SDI/HDMI video without audio)
Factory Reset:
Resets all configuration parameters to the Factory Default settings.
Configuration Tab: