Apantac CLN-SW-6x1-M User manual

HDMI-8x8
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
CLN-SW-6x1-M
User Manual

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
1
Copyright and Trademarks:
All rights reserved by APANTAC LCC, Portland, Oregon, USA. No part of this document
may be reproduced in any form or by any means without written permission from the
product manufacturer. Changes are periodically made to the information in this document.
They will be incorporated in subsequent editions. The product manufacturer may make
improvements and /or changes to the product described in this document at any time.
All the registered trademarks referred to this manual belong to their respective
companies.

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
2
Table of Contents
1.0!WHAT’S IN THE BOX? ................................................................................................ 3!
2.0!Features ................................................................................................... 3!
3.0!Specifications ........................................................................................... 4!
4.0!Front/Rear Panels ..................................................................................... 5!
4.0.1!Front Panel................................................................................................................... 5!
4.0.2!Button Descriptions..................................................................................................... 5!
4.0.3! Rear Panel .................................................................................................................. 7!
5.0! Connections ............................................................................................................... 9!
5.1! I/O Connections ........................................................................................................ 9!
5.1.1! Output LED................................................................Error! Bookmark not defined.!
5.2! IR Pass-Through Connection..................................Error! Bookmark not defined.!
5.3! IR EXT Connection.................................................................................................. 10!
5.4! Remote Communications ....................................................................................... 11!
5.5! LAN Connection ....................................................................................................... 11!
5.6! Serial Communication............................................................................................. 12!

HDMI-8x8 Matrix Switch
3
1.0 WHAT’S IN THE BOX?
CLN-SW-6x1-M Switch
RS-232 Communication Connecting Cable
Power Cord
IR Extender
Female 1x5 screw terminal
IR Remote Control
Rack Ear Screws
2 Rack-Mount Bracket
2.0 Features
§ Seamless switching with different resolutions
§ Multiple different types of inputs VGA, YPbPr, DVI or HDMI
§ Up/down/cross converter with VGA, YPbPr, DVI and HDMI inputs with HDMI,
VGA and audio ouptuts..
o Supports 1080i to 1080P conversion
o Suppports VGA to 1080P upconversion

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
4
o Supports 1080P@60 to 720P@60 down conversion
o Supports 576i@50 to 1080P@60 cross conversion
§ Output resolution up to 1080P
§ Supports 2 aspect ratio modes
o 1:1 – retains the original input aspect ratio
o Full – Always stretch the input image to fit the output aspect ratio
§ Cascadable control via RS-485
§ Supports both HDMI and VGA outputs
§ RS-232 serial control
§ Ethernet (web interface) control
§ Discrete audio input and output
§ IR remote control
§ EDID management (copy from output port to the 3 HDMI inputs)
§ HDCP compliant
3.0 Specifications
Function
CLN-SW-6x1-M
Modular Input cards
1 x VGA, 1 x YPbPr, 1 x DVI, 3 x HDMI
Output Connector
1 x HDMI Type A, 1 x VGA DB15
RS-232 Connector
DB9 Female
LAN Connector
RJ-45
RS-485 connector
2
Audio Port
1 x audio output, 4 audio inputs
2 pin dip switch
1
8 pin dip switch
1
Power
90 VAC – 250 VAC, 50/60Hz
Weight
4 kg
Dimension
440 x 240 x 44 mm
Maximum resolution
1080P@60Hz
Maximum Pixel Clock
225 MHz
HDMI cable distance
10 meters
Baud rate
9600 bps; 8 data bits, 1 stop bit, no parity
Ethernet protocol
HTTP, DHCP, TCP/IP, ICMP (ping)
Program control
Web server, GUI application
Serial control port
RS-232 (DB9), RS-485 (1x5 screw terminal)
Remote control
Portable remote control, IR receiver/blaster

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
5
Web server
LAN, RJ-45
4.0 Front/Rear Panels
4.0.1 Front Panel
Figure 4-1 CLN-SW-6x1-M Front Panel
4.0.2 Button Descriptions
• Button 1: VGA + audio
• Button 2: YPbPr + audio
• Button 3: DVI + audio
• Buttons 4 ~ 6: HDMI inputs (4, 5 and 6)
• Aspect Ration
Full
Figure 4.2: Aspect ratio Full
1:1
Figure 4.3: Aspect ratio 1:1

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
6
Figure 4.4: Aspect ratio 1:1
• Resolutions: To set the output resolution to 720P or 1080P
• IR: IR receiver can receive signals from the remote control

HDMI-8x8 Matrix Switch
6
4.0.3 Rear Panel
Figure 4-5 CLN-6x1-M Rear Panel
- Power: 90 to 250 50/60Hz
- IR Rx: Used to connect the IR receiver cable for IR control
- IR EXT port: This is used to connect the IR receiver cable for the matrix
remote control
- Input: HDMI 1~4
- Output: RJ-45 (1~4). HDBT-1-Rs-II-POE receiver is needed on each
output
- RS-232: Remote control or GUI over serial communication.
- RS-485: Allow multiple units to be controlled.
- LAN: Access the web server
- DIP Switch 8 pin and 2 pin DIP switches for configuration
8 pin DIP Switch
• Pins 1-5: ID
• Pin 6: Master/slave
• Pin 7: RS-232/LAN
• Pin8: IP Reset
2 pin DIP switch (RS-485 termintor): RS-485 terminator for On/Off
- VGA output: The resolution will match the HDMI output
- Audio output: Can be connected to the speakers
- HDMI output: Output is encrypted with HDCP

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
8
- Inputs 1~6 modular cards
o Input 1: VGA + audio
o Input 2: YPbPr + audio
o Input 3: DVI + audio
o Inputs 4 ~ 6: HDMI inputs (4, 5 and 6)
VGA E-DDC assignment
DVI connector assignment
HDMI Type A connector assignment

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
9
Audio inputs ports: VGA, YPbPr and DVI inputs can be companied with discrete
audio inputs
5.0 Connections
Figure 4.6: Connection diagram
5.1 I/O Connections
Use a HDMI cable to connect any HDMI devices to the Matrix. Use a CATx cable to
connect the HDBT-1-Rs-II-POE to the output (RJ-45)

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
10
Figure 5.1: Input connections
Figure 5.2: Output connection
5.3 IR EXT Connection
An IR receiver cable is provided to extend the IR receiver to a more convenient
location.

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
11
Figure5.5: IR extension connection
5.4 Remote Communications
Use the supplied RS-232 cable to connect the computer’s serial port (COM1 or COM2)
to the RS-232 port of the CLN-SW-4x4-HDBT to enable remote control via serial
interface.
Figure 5.6: RS-232 and Control PC connection
5.5 LAN Connection
CLN-SW-4x4-HDBT also supports a LAN port that allows you to control the switch
through browser.
Figure 5.7: LAN port and Control PC Connection

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
12
5.6 Serial Communication
The CLN-SW-4x4-HDBT has standard RS-232 and RS-485 communication ports.
5.6.1 RS-232 Pin out
Pin No.
Leg
Description
1
N/u
Null
2
Tx
Send
3
Rx
Receive
4
N/u
Null
5
Gnd
Ground
6
N/u
Null
7
N/u
Null
8
N/u
Null
9
N/u
Null
Figure 5.8

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
13
Figure 5.9
Figure 5.10
5.6.2 RS-485 Pin out
Figure 5.11 RS-485 port
Pin 1 Tx (+): Tx (+) – Trasmitted Data +
Pin 2 Tx (-): Tx (-) – Transmtted Data –
Pin3 GND: Ground
Pin4 Rx (+): Rx (+) – Received Data +
Pin5 Rx (-): Rx (-) – Received Data –
Note: RS-232/485 baud rates are 9600bps, no odd or een, 8 bit , 1 bit stop (9600,
N, 8, 1)

HDMI-8x8 Matrix Switch
11
5.6.4 DIP Switch (8 pins)
Figure 5.12: DIP Switch
Dip switch pins 1 to 5: Down position (ON) is “0”, the up position (OFF) is “1”. The
default value is “ON”
Dip switch pin 6: Master/slave (enable/disable). Only the master can be controlled
by the external controller, the others switches in the system must be slave.
• ON: RS-485 is the master in the serial chain and RS-232/LAN is enabled
• OFF: RS-485 is the slave in the serial chain and RS-232/LAN is disabled
Dip switch pin 7: Switch between RS-232 or LAN connection. The default value is
“OFF”
• ON: RS-232
• OFF: LAN
Dip switch Pin 8: Resets the web server IP address to 192.168.0.3, the default value
is “OFF”.
To reset the IP address
1. Set Pin 8 to ON and restart the matrix
2. After the matrix starts, shut it down again after 10 seconds
3. Set Pin 8 to OFF, then power on the matrix, the IP address will be set to
default value: 192.168.0.3
5.6.5 DIP Switch (2 pins)

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
15
Figure 5.16: 2 positio DIP switch
RS-485 terminator DIP switch:
ON: RS-485 terminator ON
OFF: RS-85 terminator OFF
5.6.6 Device ID Settings
When multiple matrices are connected to a single PC, or when multiple matrices are
serially connected, the device ID determines which matrix is to be controlled. This
can be set by using the On/Off switches on the real panel.

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
16

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
17
6.0 Switcher Application Software
6.1 Software Introduction
The <AV Matrix> matrix control software is used in many different Apantac
products.
6.1.1 Software Description
The <AV Matrix> is a matrix testing application. The operating environment is as
follows,
- Windos 7/98/2000/NT/XP/Vista
- 32 MB RAM
- 10 MB of Hard Disk
- CD-ROM
- At least one serial port
6.1.2 Software Installation
Double click on the AV Matrix.msi in the CD to install the software, click “Next”, and
follow the instructions on screen.

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
18
Figure 6.1: AV Matrix Installation Window
6.1.3 Connect switch and PC
1. Turn off CLN-SW-6x1-M
2. Connect the RS-232 to the PC’s RS-232 port
3. Make sure the DIP switches on the rear panel are set to Master
6.2 Configuration
Once the installation is complete, click on the <AV Matrix> Icon to launch the
application. In the “Options” dialogbox, select the comport and baud rate, then
click “OK”.
Figure 6.2: Matrix Option Dialog

CLN-SW-6x1-M
APANTAC LLC, 7470 SW BRIDGEPORT ROAD, PORTLAND, OR 97224
[e-mail], TEL: [phone], FAX: [phone]
19
Figure 6.3: AV Matrix application main window
Note: The device ID is based on the DIP switch on the rear panel
Slide the scroll bar on the lower left area of thw main window to view all contents,
including ID, Name, Audio, Video, Input, Output, Presets, VI Plug, AI Plug, VO Plug,
AO Plug, EDID Type, Volume and etc.
6.2.1 Communication Protocol
Communication protocol: See Apendix A
6.3 LAN Web Interface
Launch the browser on the PC, type in the IP address, http://192.168.0.3 to log into
the AV Matrix control configuration.