Apelson UBGHJ605M User manual

1
UBGHJ603
UBGHJ605M
UBGHJ607
GB

2
[02] x 1
[03] x 2
[01] x 1 [04] x 1
[05] x 1 set
[06] x 1
[07] x 4
1 : 1
[08] x 4
[09] x 4
[10] x 1
[11]x 1set

3
UBGHJ603
UBGHJ605M
UBGHJ607
Built-in Gas Hob
Installation
GB
24

4
GB
Let's
get started...
Getting started... 05
Before you start 06
Safety 07
In more detail... 09
Product functions
Operation
Care and maintenance
Troubleshooting
Recycling and disposal
Technical and legal information
10
13
15
15
16
Appendix
Installation
11
23

5
Getting
Started...
Getting started...
GB
Before you start
Safety
06
07

6
Getting started...
GB Before you start
Tools required
Before you start
Check the package and make sure you have all of the parts
listed.
Decide on the appropriate location for your product.
or handling to prevent personal injury or damage to the
product.
ordering replacement parts.
If you sell the appliance, give it away, or leave it behind
when you move house, make sure you also pass on this
manual so that the new owner can become familiar with the
appliance and its safety warnings.
SILICONE
To avoid the risks that are always present when you use
an electrical appliance it is important that this appliance is
installed correctly and that you read the safety instructions
carefully to avoid misuse and hazards. please keep this
instruction booklet for future reference and pass it on to any
future owners. after unpacking the appliance please check
that it is not damaged. If in doubt, do not use the appliance but
contact Customer Services on 0344 800 1128 (UK),
014475261 (Ireland)

7
Getting
started...
GB
Safety
These instructions are for your safety. Please read
through them thoroughly prior to installation and
retain them for future reference.
This appliance complies with all current European
safety legislation, however, the Manufacturer must
emphasise that this compliance does not prevent the
surfaces of the appliance from heating up during use
and remaining hot during its operation.
Accessible parts may become hot during use. Young
children should be kept away. Care should be taken
to avoid touching the appliance (e.g hob, cooker).
The Manufacturer highly recommends that this
appliance be kept out of the reach of babies and
small children.
Children should be supervised to ensure that they do
not play with the appliance.
This appliance is not intended for use by persons
(including children) with reduced physical sensory, or
mental capabilities, or by those who lack experience
and knowledge, unless they have been given
supervision and instruction concerning the use of the
appliance by a person responsible for their safety.
Means for isolating the appliance must be incorated in
the fixed wiring in accordance with the current wiring
regulations. An all-pole disconnection switch having a
contact separation of at least 3 mm in all poles should
be connected in fixed wiring.
• All installation work must be carried out by a
qualified Gas Safe registered engineer.
• This appliance must be installed correctly by a
manufacturer’s instructions.

8
Getting started...
GB Safety
We also recommend that great care be taken during use
and cleaning. Read the cleaning and maintenance
sections for this appliance carefully.
A steam cleaner is not to be used.
The appliance is not intended to be operated by
means of external timer or separated remote-
control system.
The appliance is for domestic use only.
When a cooking zone has been on for a long time, the
surface remains hot for some time afterwards so do not
touch the metal surface.
Do not leave hot oils or fats unattended as they may catch
light.
The Manufacturer declines all liability for personal or
material damage as a result of misuse or incorrect
installation of this appliance.
Damaged power cables should be replaced by a
competent person or qualified electriaian
Make sure that the power cord is not caught under or in
the appliance and avoid damage to the power cable.
Do not allow the electric cables to touch the hot parts of
the appliance.
Do not install the appliance outdoors in a damp place or
in an area which may be prone to water leaks such as
under or near a sink unit. In the event of a water leak
allow the machine to dry naturally.
Please dispose of the packing material carefully.
Do not use flammable sprays in close vicinity to the
appliance
Do not store detergents or flammable materials beneath
the hob

9
In more detail...
In more
detail...
GB
Product functions
Operation 11
Care and maintenance
Troubleshooting 15
Recycling and disposal
Technical and legal information 16
10
13
15

10
GB
IE
In more detail...
GB
Product functions
Control elements
Caution: This diagram may be slightly different from the layout of the appliance.
Operation
• 4 x Burners: Four zones of cooking.
• Flame safety device (FSD): Stops the gas supply to the gas hob when
the ame goes out.
• auto - ignition
• LPG conversion kit supplied.
Reference Description Qty Reference Description Qty
A Auxiliary burner 1 D Panel 1
B Semi-rapid burner 2 E Burner Cap 5
C Wok burner 1 F Pan Support 4
E
F
B D
E
A
C
F

11
In
more
detail...
GB
Operation
Caution
• If there is no electric current you can light the burners with
piezo electric spark gas ignitor.
• The burners can only be lit with safety thermocouples when
the knob is on MAXIMUM.
Operation
Use of the burners
> Automatic electric “ON” switch for burners with safety device
(thermocouples)
:
•
counter-clockwise direction so that the knob is at MAXIMUM.
•
Once the burner is lit, keep the knob pressed in for about 10 seconds
goes out when the knob is let go, repeat the operation.
On the control panel (g.4) to the left of every knob there is a diagram to
indicate the burner to which the knob in question refers. The burners can
be switched on in several ways, according to the type of appliance and its
individual features.

12
GB
IE
In more detail...
GB Operation
NOTE:
>
Burner Minimum Diameter Maximum Diameter
Wok 240mm 280mm
Medium (semi-rapid) 140mm 180mm
Small (auxiliary) 120mm 140mm
WARNING
If you use a saucepan that is smaller than the recommended diameter
the ame will spread beyond the bottom of the vessel, causing the
handle to overheat.
Never leave empty pot or pans over a lit burner.
Do not use tools for gill cooking on gas on glass hobs.
The use of a gas cooking appliance produces heat and humidity in the
place where it is installed.
Therefore, you need to ensure the place is well ventilated, keeping the
natural ventilation openings clear and using a mechanical ventilation
device/ ue or electric fan.
Intensive or prolonged use of the appliance may require additional
ventilation, such as opening a nearby window or increased ventilation
efency obtained by increasing the power of the mechanical ventilators,
where applicable.
Advice for the best use of the burner:
When boiling point is reached, turn the knob to MINIMUM.
Always use pans with a lid .
>
>
>
>

13
In
more
detail...
GB
Care and maintenance
Appliance cleanliness
>
>
>
:
Warning
Always switch off the electricity supply before
performing maintenance work. In the event of a fault,
contact customer services.
Caution
• Use soapy water and a cloth for cleaning. Never
use abrasive powders.
• Avoid banging pots and pans down on the hob.
• Do not leave any empty pan on the heating zone.
FUSE
OFF
>
Cleaning the hob panel.
Regularly wipe over the hob top with a soft cloth well rung out in warm water
to which a little washing up liquid has been added. Avoid use of the following:
1) Household detergent and bleaches. 2) Soap impregnated scouring pads.
3) Steel wool. 4) Bath/sink stain removers.
Cleaning the pan supports.
If washing them by hand, take care when drying them as the enameling and
dieing process occasionally leaves rough edges. If necessary remove
stuborn stains using a paste cleaner.
Cleaning the burners.
The burner caps and crowns can be renoved for cleaning. Wash the burn-
er caps and crowns using hot soapy water and remove marks using a mild
paste cleaner.
A well moistened soap impregnated steel sool pad can be used with caution
if the marks are particularly difcult to remove. After cleaning make sure to
dry using a soft cloth.
Note: It is very important to keep the thermocouples and the ignition candles
in a clean condition to prevent problems lighting and maintaining a ame on
the burners.
The appliance should be cleaned after use.
Wipe the inner and outer surface of the appliance and its accessories
with wet cloth.
Any liquid overowing from the pan must always be removed with
a cloth.
The surface of the hob may be easily cleaned as follows

14
GB
IE
In more detail...
GB
Replacement of parts
Warning
Always switch off the electricity supply before
performing maintenance work. In the event of a fault,
contact customer services.
Care and maintenance
FUSE
OFF

15
In
more
detail...
GB
Troubleshooting
The following circumstances may not be a problem. Do not contact the
If your appliance is still not functioning properly after making the above
checks, please contact customer services.
1. Check that the mains supply has not been switched off.
2. Check that the fuse in the spur has not blown.
3. Ensure that the burner components are not excessively soiled as
this can lead to ignition problems.
Do not take the appliance apart yourself, as you may damage the hob.
Before calling After Sales Service, please do the following:
1. Check that the appliance is correctly connected.
2. Read the failure text above. If you are still unable to solve the
problem, switch off the appliance, do not try to take it apart
and call customer services.
Troubleshooting
Recyling and disposal
Environmental protection
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice.
The symbol on the product or its packaging indicates that this
product cannot be treated as normal household waste. This
product must be handed over to an electric and electronic
equipment collection point for recycling.
On ensuring that this product is disposed of correctly, you will help to
avoid possible negative consequences for the environment and public
health, which could occur if this product is not handled correctly. To receive
more detailed information about recycling this product, contact your local
government, domestic waste disposal services or the outlet where the
product was bought.

16
GB
IE
In more detail...
GB Technical and legal
information
Technical data
Power Supply V/Hz 220-240 Vac 50Hz
Gas Pressure mbar G20-20mbar
G30-28~30 / 37mbar
External Dimensions HxDxW mm 110x510x590
NG (G20 20mbar)
Injector Dia. (mm) and kW
LPG(G30 28~30/37mbar)
Injector Dia. (mm) and kW
Gas Category Dia kW Dia kW
Wok Burner 1.24 3.0 0.88 3.0
Semi rapid burner 0.98 1.75 0.691.75
Auxiliary burner 0.74 1.0 0.511.0
Overall Dimensions:
Width: 590mm Depth: 510mm
Cut-out Dimensions
Width: 555mm Depth: 475mm

17
In more detail...
GB
Technical and legal
information
All installation work must be carried out by a
Before connecting the mains supply ensure that
the mains voltage corresponds to the voltage on
the rating plate inside the cooker hood.
Warning: THIS APPLIANCE MUST
BE EARTHED.
Mains Supply could be connected to the Mains Voltage by Direct
Connection
Direct Connection
If the appliance is being connected directly to the mains an
omnipolar circuit-breaker must be installed with a minimum
opening of 3mm between contacts.
If the cable is damaged or to be replaced, the operation must be
avoid any accidents.
The installer must ensure that the correct electrical connection has
been made and that it complies with wiring diagram.
The cable must not be bent or compressed.
The cable must be checked regularly and replaced by authorized
technicians only.
DOUBLE POLE SWITCHED
FUSED SPUR OUTLET
USE A 3AMP FUSE
FUSE ON

18
GB
IE
In more detail...
GB
Electrical Requirements
Any permanent electrical installation must comply with the latest
I.E.E. Regulations and local electricity company regulations. For
roll of the National Inspection Council for Electrical Installation
Contracting (NICEIC) should undertake the electrical installation.
Electrical Connection
Before connecting the mains supply ensure that the mains
voltage corresponds to the voltage on the rating plate inside
the appliance.
WARNING: THIS APPLIANCE MUST BE EARTHED
The appliance is supplied with a 3-core mains cable and must be
connected to the electricity supply via a double pole switch having
a 3mm minimum contact gap on each connector.
For UK only
A Switched Fused Connection Unit to BS 1363 Part 4 is
recommended.
The fuse must be rated at 3 Amps.
The wires in the mains lead are coloured in accordance with the
following code:
Brown = L - Live
Blue = N - Neutral
Green/Yellow = - Earth
The connection point must be placed in a position adjacent to the
appliance so as to be readily accessible for an engineer in the
event of a breakdown.
Disconnect the appliance from the mains supply before
carrying out any kind of maintenance or cleaning.
Technical and legal
information

19
In
more
detail...
GB
Installation Guidelines
Gas Supply Requirements (UK and ROI)
This installation must comply with the Gas Safety Regulations 1984.
The connection to the gas supply must comply with all current
regulations in force.
We are not legally able to offer advice on the installation of gas
appliances to non Gas Safe registered personnel.
Ventilation
All rooms require a window or equivalent (e.g. a door) which can be
opened. Some rooms require a permanent vent or extractor in addition
to a window (see below).
This unit must not be used in a room which is less than 5m3.
The following table details the requirements based on the kitchen
volume (L x W x H) in m3.
The above requirements also allow use of a gas oven and grill but if
there are any other fuel burning appliances in the same room, consult
the relevant British Standard (BS5440) or Gas Safe manual.
The above requirements also allow use of a gas oven and grill but if
there are any other fuel burning appliances in the same room, consult
the relevant British Standard (BS440) or Gas Safe document.
What you should do if you smell gas?
Switch off the gas supply
Open doors and windows
Call Transco 0800 111 999
Room Volume (m3)A ir vent required (cm3)
5 100
6 to 10
6 to 10
50
No permanent vent required if a
door opens to the outside
11 or more None required
Technical and legal
information
A

20
GB
IE
In more detail...
GB
Gas connection
Changing the nozzles
NOTE: The LPG nozzles are provided in a separate bag marked “LPG” and
if they are changed and the natural gas jets retained then the label should be
changed to “NATURAL”.
Lift up the burners and unscrew the nozzle using an dedicated tool and
replace the nozzles with those designed for LPG gas supply.
Caution
The hob installation and burner changes must be
carried out by a competent person. ie a Gas Safe
02
[08] x4
x1 [08]
01
[11]x1set
x1
Technical and legal
information
should mark the appliance to show which injectors are being used.
Note: When the injectors have been changed the gas technician
(see table on page 16)
[11]