Appsys ProAudio ADX-8 User manual

ADX-8
Extender for ADAT® and TOSLINK® optical
audio connections over Cat5
User s Manual

User s Manual
1. DESCRIPTION
1.1. Foreword
With the ADX-8 Extender, digital audio data can be losslessly transmitted over
large distances (up to 100 m / 328 ft.), using standard Cat5 network cable as the
transport medium.
Example usages
Extending ADAT connections in the recording studio (Digital Multicore)
Connect your PC in the oce room to your hi-fi system in your living room
Transmit digital audio data to a distant building or room (e.g. your summer
house or your hobby room)
Advantages
Lossless transmission over digital connection (similar to professional studio
equipment standard AES/EBU)
Cheap installation using standard low-cost network cabling
Eliminates hum and other noise due to galvanic isolation
Compatible with all audio formats which can be sent over TOSLINK
Quality product “Made in Switzerland“
1.2. Box Contents
ADX-8 Sender (TOSLINK in to Cat5 out)
ADX-8 Receiver (Cat5 in to TOSLINK out)
Wide-range AC power adapter (country specific plug)
This manual
2. SETUP
2.1. Precautions
Use the Cat network cable ONLY to connect the ADX-8
devices together. NEVER connect it to network devices, as this
could result in damage of both the ADX-8 and/or the network
device.
2

ADX-8
2.2. Connection scheme
Connect the supplied AC adaptor (power supply) to the sender (labeled “DC IN“)
Connect the output of your audio signal source (soundcard, ADAT source
CD/DVD player...) to the optical input of the sender (labeled “TOSLINK In“) using
a standard TOSLINK optical cable
Connect the sender (Port “Cat5 Out“) to the receiver (Port “Cat5 In“), using a
standard 1:1 Cat5 (or better) network cable.
Connect the receiver s output (labeled “TOSLINK Out“) to the optical input of
your playback device (amplifier, receiver or likewise), using a standard TOSLINK
optical cable. For ADAT transmission, the playback device may need to have its
wordclock source set to its optical input. Please consult the instructions for your
playback device for more information.
The ADX-8 Extender is now ready to operate.
3

User s Manual
3. SPECIFICATIONS
Model number ADX-8
Input/Outputs Optical connector, F05 Type
TO LINK® compatible
Maximum distance between sender and receiver 100 m (328 ft.)
upported audio formats •ADAT Lightpipe ®
•/PDIF ® (up to 96kHz / 24 bit)
•Dolby Digital ® 5.1 (AC-3)
•DT ®
•all other TO LINK compatible formats up to 13.2
MBit/s (NRZ-encoding)
Pinout Cat5 cable 1 (orange/white) DATA+
2 (orange) DATA–
3 (green/white) NC
4 (blue/white) +12V
5 (blue) +12V
6 (green) NC
7 (brown/white) GND
8 (brown) GND
Power supply 9-15V DC 100mA, Polarity: Center Positive
Plug: ID=2.5mm OD=5mm Length=9mm
4. APPENDIX
4.1. Warranty
We oer a full two (2) year warranty from the date of purchase. Within this period,
we repair or exchange your device free of charge in case of any defect*. If you
experience any problems, please contact us first. We try hard to solve your
problem as soon as possible, even after the warranty period.
* Not covered by the warranty are any damages resulting out of improper use,
willful damage, normal wear-out (especially of the connectors) or connection with
incompatible devices.
4.2. Manufacturer contact
Appsys ProAudio
Rolf Eichenseher
Bullingerstr. 63 / BK241
CH-8004 Zürich
Switzerland
www.appsys.ch
[email protected]h
Phone: [phone]
Mobile: [phone]
4

ADX-8
4.3. FCC Compliance
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
This equipment has been verified to comply with the limits for a class B computing
device, pursuant to FCC Rules. In order to maintain compliance with FCC
regulations, shielded cables must be used with this equipment. Operation with
non-approved equipment or unshielded cables is likely to result in interference to
radio and TV reception. The user is cautioned that changes and modifications
made to the equipment without the approval of manufacturer could void the user’s
authority to operate this equipment.
4.4. Recycling
According to EU directive 2002/96/EU, electronic devices with a
crossed-out dustbin may not be disposed into normal domestic
waste. Please return the products back for environment-friendly
recycling, we ll refund you the shipping fees.
4. . About this document
Rev. Changes
6 Reformatted document
Added FCC compliance statement
All trademarks mentioned in this document are property of the respective owners.
All information provided here is subject to change without prior notice.
Document Revision: 6 · 2019-11-21
Copyright © 2010-2019 Appsys ProAudio · Printed in Switzerland
5