Aprilaire Z10IDT Setup guide

SPECIFICATIONS
Communications 2.4 MHz
Wireless range 35 feet
Temperature
measurement
range/accuracy
Accuracy: ±2°F (40°F to 105°F), ±5°F
outside of this range
Range: -40°F to 125°F
Humidity
measurement
range/accuracy
Accuracy: ±5% RH between 20% and
80% RH
Range: 0.5% to 99.5% RH
Battery life Approximately 1 year
Battery type Lithium CR2032 type
FEATURES
WHEN USED WITH APRILAIRE MODEL S86WMUPR
THERMOSTAT:
• Sensor controlled scheduling – heat/cool calls can
be controlled by averaging inputs from all sensors, or
control a scheduled event with a specic individual
sensor input.
• Pair up to 8 indoor temperature sensors with your
AprilAire thermostat.
BATTERY REPLACEMENT
1. Slide the backing
plate down to
remove from
sensor.
2. Remove battery.
3. Replace battery
with lithium
CR2032 type.
4. Replace backing
plate on sensor.
MOUNTING THE WIRELESS
INDOOR SENSOR
NOTE: Pair sensor with Wi-Fi thermostat before mounting.
The sensor should be mounted:
• On an interior wall, in a frequently occupied space.
• Within 35 feet of thermostat.
• Approximately 5 feet above the oor.
• At least 18” from the outside wall.
Do not mount the sensor:
• Behind doors, in corners or other dead air spaces.
• In direct sunlight, near lighting xtures, or other
appliances that give off heat.
• On an outside or unconditioned area wall.
• In the ow of a supply register, in stairwells, or near
outside doors.
• On a wall with concealed pipes or ductwork.
PAIRING THE SENSOR TO THE
S86WMUPR THERMOSTAT
1. On the thermostat, navigate
to wireless sensor settings:
Menu > Settings > Installer
Settings (press and hold
UP and DOWN 5 seconds)
> Wireless Sensors > Add.
2. On the sensor, press and
hold the pairing button 5
seconds (the red indicator
on the front of the sensor
will start ashing).
3. On the thermostat, select Continue and wait for the
pairing process to complete.
LOW BATTERY DISPLAY
When the battery gets below 30% life left the sensor will
ash the LED once every 10 seconds. The connected/
paired device will display sensor low battery screen
(see your thermostat or connected device manual).
DIMENSIONS
Sensor
INSTALLATION AND
OPERATOR’S MANUAL
Model Z10IDT
Wireless Indoor Temperature
and Humidity Sensor
READ AND SAVE THESE INSTRUCTIONS
1.79” 0.53”
1.79”
BACKING
PLATE
SENSOR
BATTERY
PAIRING
BUTTON
90-2709
90-2706
90-2706
1
2

SENSOR LED AND BUTTON
FUNCTIONALITY
LED INDICATOR
LED STATUS
Flashes once per
second
Connectivity status (pairing
mode). NOTE: The sensor exits
pairing mode after 30 seconds.
Flashes once per
10 seconds Battery low power status.
BUTTON FUNCTION
Press and hold 5 seconds Enter pairing mode.
TROUBLESHOOTING
If the wireless sensor is experiencing connection issues
with the thermostat, verify the following:
1. Connect the thermostat to a Wi-Fi network to verify
the latest rmware is installed. The latest rmware
will automatically install once connected to Wi-Fi.
2. On the sensor, press and release the pairing button
once. This will send updated information to the
thermostat.
3. On the thermostat, navigate to wireless settings:
Menu > Settings > Installer Settings (press and hold
UP and DOWN 5 seconds) > Wireless Sensors > View.
4. Note the RSSI value located within the View Sensor
screen. The RSSI value should be greater than
-70 dBm (see illustration below).
a. If the RSSI value is less than -70 dBm, relocate the
sensor and repeat steps 2-4.
b. If the RSSI is greater than -70 dBm and
connection issues persist, contact AprilAire
customer support at 800.334.6011.
IC WARNING
This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s
licence-exempt RSS(s). Operation is subject to the following two
conditions: (1) This device may not cause interference. (2) This device must
accept any interference, including interference that may cause undesired
operation of the device
法语警告语句
Cet appareil contient des émetteurs / récepteurs exemptés de licence
conformes aux RSS (RSS) d’Innovation, Sciences et Développement économique
Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet
appareil ne doit pas causer d’interférences. (2) Cet appareil doit accepter
toutes les interférences, y compris celles susceptibles de provoquer un
fonctionnement indésirable de l’appareil
FIVE YEAR LIMITED WARRANTY
Your AprilAire® Wireless Indoor Temperature and Humidity Sensor is expressly
warranted for ve (5) years from date of installation to be free from defects
in materials or workmanship.
AprilAire’s exclusive obligation under this warranty shall be to supply, without
charge, a replacement for any sensor which is found to be defective within
such ve (5) year period and which is returned, together with the date of
installation, no later than thirty (30) days after said ve (5) year period by
you to either your original supplier or to AprilAire, Madison, Wisconsin 53701.
THIS WARRANTY SHALL NOT OBLIGATE APRILAIRE FOR ANY LABOR COSTS AND
SHALL NOT APPLY TO DEFECTS IN WORKMANSHIP OR MATERIALS FURNISHED BY
YOUR INSTALLER AS CONTRASTED TO DEFECTS IN THE SENSOR ITSELF.
IMPLIED WARRANTIES OF MERCHANTABILITY OF FITNESS FOR A PARTICULAR PURPOSE
SHALL BE LIMITED IN DURATION TO THE AFORESAID FIVE YEAR PERIOD. APRILAIRE’S
LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, OTHER THAN DAMAGES
FOR PERSONAL INJURIES, RESULTING FROM ANY BREACH OF THE AFORESAID IMPLIED
WARRANTIES OR THE ABOVE LIMITED WARRANTY IS EXPRESSLY EXCLUDED. THIS
LIMITED WARRANTY IS VOID IF DEFECT(S) RESULT FROM FAILURE TO HAVE THIS SENSOR
INSTALLED BY A QUALIFIED HEATING AND AIR CONDITIONING CONTRACTOR. IF THE
LIMITED WARRANTY IS VOID DUE TO FAILURE TO USE A QUALIFIED CONTRACTOR, ALL
DISCLAIMERS OF IMPLIED WARRANTIES SHALL BE EFFECTIVE UPON INSTALLATION.
Some states do not allow limitations on how long an implied warranty lasts
or the exclusion or limitation of incidental or consequential damages, so the
above exclusions or limitations may not apply to you.
This warranty gives you specic legal rights and you may also have other
rights which vary from state to state.
This equipment if installed in strict accordance with the manufacturer’s
instructions, complies with the limits for a Class B computing device pursuant
to Subpart J of Part 15 of FCC Rules.
WARRANTY REGISTRATION
Visit us on-line at aprilaire.com to register your AprilAire product. If you do
not have on-line access, please mail a postcard with your name, address,
phone number, product purchased and date of purchase to: AprilAire, P.O.
BOX 1467, Madison, WI 53701
Your warranty registration information will not be sold or shared outside
of this company.
FCC AND ISED COMPLIANCE
STATEMENTS
Contains FCC ID: 2AUXB-DSBC070
Contains IC: 25658-DSB070
This device complies with Part 15 of the FCC Rules and with Innovation, Science
and Economic Development Canada’s License-exempt RSS standard(s).
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference
that may cause undesired operation.
Changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
FCC Interference Statement – Part 15.105 (b)
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
To comply with FCC and Innovation, Science and Economic Development
Canada’s RF exposure limits for general population/uncontrolled exposure, the
antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be operating in
conjunction with any other antenna or transmitter, except in accordance
with FCC multi-transmitter product procedures.
B2209932B • 61002193 • 02.23
© 2023 AprilAire | aprilairepartners.com | 800.334.6011
AprilAire reserves the right to change specications without notice.
90-2709
-110 -100 -90
Weak
Connection
Strength
Strong
Connection
Strength
-80 -70 -60 -50 -40 -30 -20 -10