APRILIA CAPONORD 1200 Guide

MANUALE STAZIONE DI SERVIZIO
2Q000020
CAPONORD 1200

MANUALE
STAZIONE DI
SERVIZIO
CAPONORD 1200
THE VALUE OF SERVICE
As a result of continuous updates and specific technical training programmes for Aprilia products, only
Aprilia Official Network mechanics know this vehicle fully and have the specific tools necessary to carry
out maintenance and repair operations correctly.
Thereliabilityofthevehiclealsodependsonitsmechanicalconditions.Checkingthevehiclebeforeriding
it, its regular maintenance and the use of original Aprilia spare parts only are essential factors!
For information on the nearest Official Dealer and/or Service Centre consult our website:
www.aprilia.com
Only by requesting aprilia original spare parts can you be sure of purchasing products that were
developed and tested during the actual vehicle design stage. All aprilia original spare parts undergo
quality control procedures to guarantee reliability and durability.
Thedescriptionsandimagesinthispublicationaregivenforillustrativepurposesonlyandarenotbinding.
While the basic characteristics as described and illustrated in this booklet remain unchanged, Piaggio &
C.S.p.A. reservesthe right,at anytime andwithout beingrequired toupdate thispublication beforehand,
to make any changes to components, parts or accessories, which it considers necessary to improve the
product or which are required for manufacturing or construction reasons.
Notallversions/modelsshowninthispublicationareavailableinallcountries.Theavailabilityofindividual
models should be confirmed with the official aprilia sales network.
The Aprilia trademark is the property of Piaggio & C. S.p.A.
© Copyright 2013 - Piaggio & C. S.p.A. All rights reserved. Reproduction of this publication in whole or
in part is prohibited.
Piaggio & C. S.p.A. Viale Rinaldo Piaggio, 25 - 56025 PONTEDERA (PI), Italy
www.piaggio.com

MANUALE STAZIONE DI
SERVIZIO
CAPONORD 1200
This manual provides the main information to carry out regular maintenance operations on your vehicle.
This manual is intended to aprilia Dealers and their qualified mechanics; several concepts have been
deliberately omitted as they are considered unnecessary. As it is not possible to include complete
mechanical notions in this manual, users should have basic mechanical knowledge or minimum
knowledge about the procedures involved when repairing scooters. Without this knowledge, repairing or
checking the vehicle may be inefficient or even dangerous. As the vehicle repair and check procedures
are not described in detail, be extremely cautious so as not to damage components or injure individuals.
In order to optimise customer satisfaction when using our vehicles, aprilia s.p.a. commits itself to
continually improve its products and the relative documentation. The main technical modifications and
changes in repair procedures are communicated to all aprilia Sales Outlets and its International
Subsidiaries.These changeswill beintroduced inthe subsequenteditions ofthe manual.In caseof need
or further queries on repair and check procedures, consult aprilia CUSTOMER DEPARTMENT, which
will be prepared to provide any information on the subject and any further communications on updates
and technical changes related to the vehicle.
NOTE Provides key information to make the procedure easier to understand and carry out.
CAUTION Refers to specific procedures to carry out for preventing damages to the vehicle.
WARNING Refers to specific procedures to carry out to prevent injuries to the repairer.
Personal safety Failure to completely observe these instructions will result in serious risk of personal
injury.
Safeguarding the environment Sectionsmarked with thissymbol indicatethe correctuse of thevehicle
to prevent damaging the environment.

Vehicle intactness The incomplete or non-observance of these regulations leads to the risk of serious
damage to the vehicle and sometimes even the invalidity of the guarantee

INDEX OF TOPICS
CHARACTERISTICS CHAR
SPECIAL TOOLS S-TOOLS
MAINTENANCE MAIN
TROUBLESHOOTING TROUBL
ELECTRICAL SYSTEM ELE SYS
ENGINE FROM VEHICLE ENG VE
ENGINE ENG
POWER SUPPLY P SUPP
SUSPENSIONS SUSP
CHASSIS CHAS
BRAKING SYSTEM BRAK SYS
CLUTCH SYSTEM CLU SYS
COOLING SYSTEM COOL SYS
BODYWORK BODYW
PRE-DELIVERY PRE DE

INDEX OF TOPICS
CHARACTERISTICS CHAR

Rules
Safety rules
Carbon monoxide
If you need to keep the engine running while working on the vehicle, please ensure that you do so in
an open or very well ventilated area. Never run the engine in an enclosed area. If you do work in an
enclosed area, make sure to use a fume extraction system.
CAUTION
EXHAUSTEMISSIONS CONTAINCARBONMONOXIDE, APOISONOUSGASWHICHCANCAUSE
LOSS OF CONSCIOUSNESS AND EVEN DEATH.
Fuel
CAUTION
THE FUEL USED TO POWER INTERNAL COMBUSTION ENGINES IS HIGHLY FLAMMABLE AND
MAY BE EXPLOSIVE UNDER CERTAIN CONDITIONS. IT IS THEREFORE RECOMMENDED TO
CARRY OUT REFUELLING AND MAINTENANCE PROCEDURES IN A VENTILATED AREA WITH
THE ENGINE SWITCHED OFF. DO NOT SMOKE DURING REFUELLING AND NEAR FUEL VA-
POURS, AVOIDING ANY CONTACT WITH NAKED FLAMES, SPARKS OR OTHER SOURCES
WHICH MAY CAUSE THEM TO IGNITE OR EXPLODE.
DO NOT DISPERSE FUEL IN THE ENVIRONMENT.
KEEP OUT OF THE REACH OF CHILDREN
Hot components
The engine and the exhaust system components become very hot and remain hot for some time after
the engine has been switched off. When handling these components, wear insulating gloves or wait
until the engine and the exhaust system have cooled down.
Coolant
The coolant contains ethylene glycol which, under certain conditions, can become flammable.
When it burns, ethylene glycol produces an invisible flame which however can cause burns.
CAUTION
TAKE CARE NOT TO POUR COOLANT ONTO HOT ENGINE OR EXHAUST SYSTEM COMPO-
NENTS; THE FLUID MAY CATCH FIRE AND BURN WITH INVISIBLE FLAMES. WHEN CARRYING
OUT MAINTENANCE OPERATIONS, IT IS ADVISABLE TO WEAR LATEX GLOVES. EVEN
THOUGH IT IS TOXIC, COOLANT HAS A SWEET FLAVOUR WHICH MAKES IT VERY ATTRAC-
TIVE TO ANIMALS. NEVER LEAVE THE COOLANT IN OPEN CONTAINERS IN AREAS ACCES-
SIBLE TO ANIMALS AS THEY MAY DRINK IT.
Characteristics CAPONORD 1200
CHAR - 8

KEEP OUT OF THE REACH OF CHILDREN
DO NOT REMOVE THE RADIATOR CAP WHEN THE ENGINE IS STILL HOT. THE COOLANT IS
UNDER PRESSURE AND MAY CAUSE BURNS.
Used engine oil and transmission oil
CAUTION
IT IS ADVISABLE TO WEAR PROTECTIVE IMPERMEABLE GLOVES WHEN SERVICING THE VE-
HICLE.
THE ENGINE OR GEARBOX OIL MAY CAUSE SERIOUS INJURIES TO THE SKIN IF HANDLED
FOR PROLONGED PERIODS OF TIME AND ON A REGULAR BASIS.
WASH YOUR HANDS CAREFULLY AFTER HANDLING OIL.
HAND THE OIL OVER TO OR HAVE IT COLLECTED BY THE NEAREST USED OIL RECYCLING
COMPANY OR THE SUPPLIER.
DO NOT DISPOSE OF OIL IN THE ENVIRONMENT
KEEP OUT OF THE REACH OF CHILDREN
Brake and clutch fluid
BRAKE AND CLUTCH FLUIDS CAN DAMAGE THE PLASTIC OR RUBBER PAINTED SURFACES.
WHEN SERVICING THE BRAKING SYSTEM OR THE CLUTCH SYSTEM, PROTECT THESE COM-
PONENTS WITH A CLEAN CLOTH. ALWAYS WEAR PROTECTIVE GOGGLES WHEN SERVICING
THESE SYSTEMS. BRAKE AND CLUTCH FLUIDS ARE EXTREMELY HARMFUL FOR YOUR
EYES. IN THE EVENT OF ACCIDENTAL CONTACT WITH THE EYES, RINSE THEM IMMEDIATELY
WITH ABUNDANT COLD, CLEAN WATER AND SEEK MEDICAL ADVICE.
KEEP OUT OF THE REACH OF CHILDREN
Battery electrolyte and hydrogen gas
CAUTION
THE BATTERY ELECTROLYTE IS TOXIC, CORROSIVE AND AS IT CONTAINS SULPHURIC ACID,
IT CAN CAUSE BURNS WHEN IN CONTACT WITH THE SKIN. WHEN HANDLING BATTERY
ELECTROLYTE, WEAR TIGHT-FITTING GLOVES AND PROTECTIVE APPAREL. IN THE EVENT
OF SKIN CONTACT WITH THE ELECTROLYTIC FLUID, RINSE WELL WITH PLENTY OF CLEAN
WATER. IT IS PARTICULARLY IMPORTANT TO PROTECT YOUR EYES BECAUSE EVEN TINY
AMOUNTSOFBATTERY ACID MAY CAUSEBLINDNESS.IFTHEFLUIDGETSIN CONTACT WITH
YOUR EYES, WASH WITH ABUNDANT WATER FOR FIFTEEN MINUTES AND CONSULT AN EYE
SPECIALIST IMMEDIATELY. THE BATTERY RELEASES EXPLOSIVE GASES; KEEP IT AWAY
FROM FLAMES, SPARKS, CIGARETTES OR ANY OTHER HEAT SOURCES. ENSURE ADE-
QUATE VENTILATION WHEN SERVICING OR RECHARGING THE BATTERY.
KEEP OUT OF THE REACH OF CHILDREN
BATTERY LIQUID IS CORROSIVE. DO NOT POUR IT OR SPILL IT, PARTICULARLY ON PLASTIC
COMPONENTS. ENSURE THAT THE ELECTROLYTIC ACID IS COMPATIBLE WITH THE BAT-
TERY TO BE ACTIVATED.
Maintenance rules
GENERAL PRECAUTIONS AND INFORMATION
When repairing, dismantling and reassembling the vehicle, follow the recommendations given below
carefully.
CAPONORD 1200 Characteristics
CHAR - 9

BEFORE DISASSEMBLING COMPONENTS
•Beforedismantling components, removedirt, mud,dust and foreignbodies fromthe vehicle.
Use the special tools designed for this bike, as required.
COMPONENTS REMOVAL
•Donot loosen and/ortighten screwsand nutsusing pliers or any othertools thanthe specific
wrench.
•Mark positions on all connection joints (pipes, cables etc.) before separating them, and
identify them with distinctive symbols.
•Each component needs to be clearly marked to enable identification during reassembly.
•Clean and wash the dismantled components carefully using a low-flammability detergent.
•Keep mated parts together since they have "adjusted" to each other due to normal wear.
•Some components must be used together or replaced completely.
•Keep away from heat sources.
REASSEMBLING COMPONENTS
CAUTION
BEARINGS MUST ROTATE FREELY, WITHOUT JAMMING AND/OR NOISE, OTHERWISE, THEY
NEED TO BE REPLACED.
•Only use ORIGINAL Aprilia SPARE PARTS.
•Comply with lubricant and consumables use guidelines.
•Lubricate parts (whenever possible) before reassembling them.
•Whentighteningnuts andscrews,start eitherfromthecomponents withthelargest diameter
or from the innermost components, proceeding diagonally. Tighten nuts and screws in suc-
cessive steps before applying the tightening torque.
•Always replace self-locking nuts, washers, sealing rings, circlips, O-rings (OR), cotter pins
and screws with new parts if the thread is damaged.
•When assembling the bearings, make sure to lubricate them well.
•Check that each component is assembled correctly.
•After a repair or routine maintenance, carry out pre-ride checks and test the vehicle on
private grounds or in an area with low traffic.
•Clean all mating surfaces, oil seal rims and gaskets before refitting. Smear a thin layer of
lithium-based grease on the oil seal rims. Reassemble oil seals and bearings with the brand
or batch number facing outward (visible side).
ELECTRICAL CONNECTORS
Electric connectors must be disconnected as described below; failure to comply with this procedure
causes irreparable damage to both the connector and the wiring harness:
Press the relative safety clips, if applicable.
•Grip the two connectors and disconnect them by pulling them in opposite directions.
Characteristics CAPONORD 1200
CHAR - 10

•If any signs of dirt, rust, moisture, etc. are noted, clean the inside of the connector carefully
with a jet of compressed air.
•Ensure that the cables are correctly fastened to the internal connector terminals.
•Then connect the two connectors, ensuring that they couple correctly (if fitted with clips, you
will hear them "click" into place).
CAUTION
DO NOT DISCONNECT CONNECTORS BY PULLING THE CABLES.
NOTE
THE TWO CONNECTORS CAN ONLY BE CONNECTED IN ONE DIRECTION: CONNECT THEM
THE RIGHT WAY ROUND.
TIGHTENING TORQUES
CAUTION
IN THE EVENT THAT A SELFBRAKING NUT IS UNSCREWED, IT IS NECESSARY TO REPLACE
IT WITH A NEW ONE.
CAUTION
REMEMBERTHATTHE TIGHTENING TORQUES FORALLFASTENINGELEMENTSONWHEELS,
BRAKES, WHEEL AXLES AND ANY OTHER SUSPENSION COMPONENTS PLAY A KEY ROLE
IN ENSURING VEHICLE SAFETY AND MUST COMPLY WITH SPECIFIED VALUES. CHECK THE
TIGHTENING TORQUES OF FASTENING ELEMENTS ON A REGULAR BASIS AND ALWAYS USE
A TORQUE WRENCH TO REASSEMBLE THESE COMPONENTS. FAILURE TO COMPLY WITH
THESE RECOMMENDATIONS MAY CAUSE ONE OF THESE COMPONENTS TO LOOSEN OR
EVEN DETACH, CAUSING A WHEEL TO LOCK OR COMPROMISING VEHICLE HANDLING. THIS
MAY LEAD TO FALLS, WITH THE RISK OF SERIOUS INJURY OR DEATH.
Running-in
Runningthe engine in correctly is essential forensuring enginelongevity andfunctionality. Twistyroads
and gradients are ideal for running in the engine, brakes and suspension effectively. Vary your riding
speed during the running in period. This ensures that components operate in "loaded" conditions and
then "unloaded" conditions, allowing the engine components to cool.
CAUTION
THE FULL PERFORMANCE OF THE VEHICLE IS ONLY AVAILABLE AFTER THE SERVICE AT
THE END OF THE RUNNING IN PERIOD.
Follow these guidelines:
•Do not twist the throttle grip abruptly and completely when the engine is working at a low
revs, either during or after run-in.
•During the first 100 Km (62 miles) use the brakes gently, avoiding sudden or prolonged
braking. That is to permit the adequate adjustment of the pad friction material to the brake
discs.
AFTER THE SPECIFIED MILEAGE, TAKE YOUR VEHICLE TO AN Official Aprilia Dealer FOR THE
CHECKS INDICATED IN THE "AFTER-RUN-IN" TABLE IN THE SCHEDULED MAINTENANCE
SECTION TO AVOID INJURING YOURSELF, OTHERS AND /OR DAMAGING THE VEHICLE.
CAPONORD 1200 Characteristics
CHAR - 11

Vehicle identification
Write down the chassis and engine number in the specific space in this booklet. The chassis number
is handy when purchasing spare parts.
CAUTION
THE MODIFICATION OF THE IDENTIFICATION CODES IS A SERIOUS PUNISHABLE CRIME.
HOWEVER, THE LIMITED WARRANTY FOR NEW VEHICLES WILL BE VOID IF THE VEHICLE
IDENTIFICATION NUMBER (VIN) HAS BEEN MODIFIED OR NOT PROMPTLY DETERMINED.
This number consists of numbers and letters, as in the example shown below.
ZD4VKA000YSXXXXXX
KEY:
ZD4: WMI (World manufacturer identifier) code;
VK: model;
A00: version variation;
0: free digit
Y: year of manufacture
S: production plant (S= Scorzè);
XXXXXX: serial number (6 digits);
ENGINE NUMBER
The engine number is printed on the base of the
engine crankcase, left hand side.
Engine No. ....................
CHASSIS NUMBER
The chassis number is stamped on the right side of the headstock.
Chassis No. ....................
Dimensions and mass
DIMENSIONS
Specification Desc./Quantity
Max. length 2245 mm (88.38 in)
Max. width (at hand guards) 1000 mm (39.37 in)
Max. height (fully extracted windshield) 1440 mm (56.69 in)
Saddle height 870 mm (34.25 in)
Wheelbase 1555 mm (61.22 in)
Kerb weight (Caponord 1200) 251 kg (553.36 lb)
Kerb weight (Caponord 1200 Travel Pack) 265 kg (584.22 lb)
Characteristics CAPONORD 1200
CHAR - 12

Specification Desc./Quantity
Dry weight (without fuel) (Caponord 1200) 233 kg (513.68 lb)
Dry weight (without fuel) (Caponord 1200 Travel Pack) 247 kg (544.54 lb)
Engine
ENGINE
Specification Desc./Quantity
Model M558M
Type 90° longitudinal V-twin, 4-stroke, 4 valves per cylinder, 2 over-
head camshafts.
No. of cylinders 2
Total engine capacity 1197 cm³ (73.05 cu in)
Bore / stroke 106 x 67.8 mm (4.17 x 2.67 in)
Compression ratio 12.0 +/- 0.5: 1
Electric Starter
Engine idle speed 1450 ± 100 rpm
Clutch Multiple-disk, oil-bathed clutch with control on the left side of
the handlebar
Lubrication Wet crankcase. Pressure system regulated by a trochoidal
pump with oil radiator.
Air filter Sponge.
Cooling Fluid
GEARBOX
Specification Desc./Quantity
Type Mechanical, 6 speeds with foot lever on the left hand side of
the engine
Transmission
GEAR RATIOS
Specification Desc./Quantity
Gear ratio Gear primary drive 40/69
1st gear ratio 14/36 (secondary)
2nd gear ratio 17/32 (secondary)
3rd gear ratio 20/30 (secondary)
4th gear ratio 22/28 (secondary)
5th gear ratio 23/26 (secondary)
6th gear ratio 24/25 (secondary)
Final drive gear ratio 17/42
Capacities
CAPACITY
Specification Desc./Quantity
Fuel tank (reserve included) 24 l (5.28 UK gal; 6.34 US gal)
Fuel reserve 4 l (0.88 UK gal; 1.06 US gal)
Engine oil 3.1 l (without oil filter change) (0.68 UK gal; 0.82 US gal)
3.35 l (with oil filter change) (0.74 UK gal; 0.88 US gal)
Coolant 2.5 l (0.55 UK gal; 0.66 US gal)
Seats 2
Maximum weight limit 460 kg (1014.12 lb)
CAPONORD 1200 Characteristics
CHAR - 13

Drive chain
DRIVE CHAIN
Specification Desc./Quantity
Type Endless (without master link) and with sealed links. No. of links
112
Model 525 ZRPK
Electrical system
ELECTRICAL SYSTEM
Specification Desc./Quantity
Battery VTX14-BS 12 V - 12 Ampere/hour
Main fuses 30A
Secondary fuses 7.5 A; 10 A; 15 A
Alternator (permanent magnet type) 13 V - 690 W at 6000 rpm
SPARK PLUGS
Specification Desc./Quantity
Standard spark plugs NGK CR8EKB
Spark plug electrode gap 0.6 - 0.7 mm (0.024 - 0.028 in)
Resistance 5 kOhm
WARNING LIGHTS
Specification Desc./Quantity
Turn indicators LED
High beam light LED
Fuel reserve LED
Cruise control warning light LED
Gear in neutral LED
General warning LED
ABS LED
ATC LED
BULBS
Specification Desc./Quantity
Low-/ high beam light 12V - 55W H11
Front daylight running lights 12V - 5W
Turn indicators 12V - 10W (White light)
Rear daylight running light / stop light LED
Licence plate light 12V - 5W
Multifunction display lighting LED
Frame and suspensions
CHASSIS
Specification Desc./Quantity
Type Component chassis (bolted). Die-cast aluminium plates and
high-strength steel tubular chassis.
Steering inclination angle 24°
Trail with suspension fully extended (without load) 128 mm (5.04 in)
SUSPENSION
Specification Desc./Quantity
Front (Caponord 1200) Sachs telescopic "UPSIDE-DOWN" (upside-down stanchions)
fork with full-adjustable stanchions with 43mm diameter (ad-
Characteristics CAPONORD 1200
CHAR - 14

Specification Desc./Quantity
justment of hydraulic brake extended on left stanchion and
compression on right stanchion and of spring preload on both)
Front (Caponord 1200 Travel Pack) Sachs telescopic "UPSIDE-DOWN" (upside-down stanchions)
fork with stanchions with 43mm diameter, hydraulic braking
dynamic adjustment during extension and compression (semi-
active Aprilia Dynamic Damping technology) on left stanchion;
and of spring preload on right stanchion, manually adjustable
Travel 170 mm (6.69 in)
Rear (Caponord 1200) Oscillating swingarm connected with cantilever type link to a
Sachs single shock absorber, with adjustment of hydraulic
braking during extension and spring preload with knob.
Rear (Caponord 1200 Travel Pack) Oscillating swingarm connected with cantilever type link to a
Sachs single shock absorber, with adjustment of hydraulic
braking during extension and compression (semi-active Aprilia
Dynamic Damping technology) with "piggy-back" tank and au-
tomated management (or manually on instrument panel) of
spring preload via electro-hydraulic system.
Wheel travel 150 mm (5.90 in)
SIZES A AND B
Specification Desc./Quantity
Size B 129.2 mm (5.07 in)
Size A 519 ± 2 mm (20.43 ± 0.07 in)
Brakes
BRAKES
Specification Desc./Quantity
Front Double floating disc, Ø 320 mm (12.60 in), radially-mounted
calliper with four Ø 32 mm (1.26 in) pistons and two calliper
pads
Rear 240 mm (9.45 in) diam. disc brake with 35 mm (1.38 in) diam.
single piston calliper
Wheels and tyres
WHEEL RIMS
Specification Desc./Quantity
Type Light alloy rims with extractable bolt
Front 3.50 x 17"
Rear 6.00 x 17"
TYRES
Specification Desc./Quantity
Tyre type (standard) DUNLOP QUALIFIER II
CAPONORD 1200 Characteristics
CHAR - 15

Specification Desc./Quantity
Front tyre 120/70 ZR17" (58W)
Front tyre pressure rider only: 2.4 bar (240 kPa) (34.81 PSI)
rider + passenger: 2.5 bar (250 kPa) (36.26 PSI)
Rear tyre 180/55 ZR17" (73W)
Rear tyre pressure rider only: 2.6 bar (260 kPa) (37.71 PSI)
rider + passenger: 2.8 bar (280 kPa) (40.61 PSI)
Supply
FUEL SYSTEM
Specification Desc./Quantity
Type Electronic injection (Multipoint)
Throttle valve diameter Ø 52 mm (2.05 in)
Fuel Premium unleaded petrol, minimum octane rating 95 (NORM)
and 85 (NOMM)
Tightening Torques
Chassis
Front side
FRONT BRAKE CALLIPER
pos. Description Type Quantity Torque Notes
1 Callipers fastening screws M10x55 4 50 ± 7.5 Nm (36.88 ± 5.53
lb ft) -
Characteristics CAPONORD 1200
CHAR - 16

FRONT BRAKE PUMP
pos. Description Type Quantity Torque Notes
1 Brake pump fixing screws M6 2 10± 1,5 Nm (7.37±1.10 lb
ft) -
CAPONORD 1200 Characteristics
CHAR - 17

CONTROLS HANDLEBAR
pos. Description Type Quantity Torque Notes
1 Upper U-bolt fixing screw M8x25 4 25±3.75Nm(18.44±2.76
lb ft) -
2 Anti-vibration weight fastening screws - 2 20 ± 3 Nm (14.75 ± 2.21 lb
ft) -
CLUTCH CONTROL
pos. Description Type Quantity Torque Notes
1 Clutch pump fixing screws M6 2 10± 1,5 Nm (7.37±1.10 lb
ft) -
2 Throttle control fixing screws M6 3 10 Nm (7.37 lb ft) -
Characteristics CAPONORD 1200
CHAR - 18

INSTRUMENT SUPPORT
Pos. Description Type Quantity Torque Notes
1 Instrument panel to trellis fixing screws M8x25 4 25 ± 5 Nm (18.43 ± 3.68 lb
ft) -
COOLING SYSTEM
pos. Description Type Quantity Torque Notes
1 Electric fan fastener screw M4x45 6 3 Nm (2.21 lb ft) -
CAPONORD 1200 Characteristics
CHAR - 19

pos. Description Type Quantity Torque Notes
2 Flanged TE screw fastening left Ra-
diator to trellis M6x25 1 10 Nm (7.37 lb ft) -
3 Flanged TE screw fastening expan-
sion tank M6x20 3 10 Nm (7.37 lb ft) -
TOP FAIRING_WINDSHIELD
Pos. Description Type Quantity Torque Notes
1 Windshield on support fastener
screw M6x18 4 10 Nm (7.37 lb ft) -
2 Bracket retainer screw M6x25 4 10 Nm (7.37 lb ft) -
Characteristics CAPONORD 1200
CHAR - 20